TEKTELIC Communications Kona T0004893 Technical Reference Manual

TEKTELIC Communications Kona T0004893 Technical Reference Manual

Lora iot all-in-one home sensor
Hide thumbs Also See for Kona T0004893:
Table of Contents

Advertisement

Quick Links

TEKTELIC C
I
.
OMMUNICATIONS
NC
Kona Home Sensor
Technical Reference Manual
Document Type: Technical Reference Manual
Document Number: T0005370_TRM
Document Version: 1.2
Product Name: Kona LoRa IoT All-in-One Home Sensor
Product Codes: T0004893
, T0004885
, T0004895
, T0004896
†Only applicable to module revisions above Rev C. Some new features are not backward
compatible with modules Rev C and below. Module revisions above Rev C only include Base and
PIR models (Base model and External Connector model Rev C have been merged into a single
Base model Rev D).
PROPRIETARY:
The information contained in this document is the property of TEKTELIC Communications Inc. Except as specifically
authorized in writing by TEKTELIC, the holder of this document shall keep all information contained herein
confidential, and shall protect the same in whole or in part from disclosure to all third parties.
© 2018 TEKTELIC Communications Inc., all rights reserved.
All products, names, and services are trademarks and registered trademarks of their respective companies.
DISCLAIMER:
Material contained in this document is subject to change without notice. The material herein is solely for
information purposes and does not represent a commitment by TEKTELIC or its representatives. TEKTELIC has
prepared the information contained in this document solely for use by its employees, agents, and customers.
Dissemination of this information and/or concepts to other parties is prohibited without the prior written consent
of TEKTELIC. In no event will TEKTELIC be liable for any incidental or consequential damage in connection with the
furnishing, performance or use of this material.
TEKTELIC reserves the right to revise this publication in accordance with formal change control procedures defined
by TEKTELIC.
TEKTELIC Communications Inc.
th
7657 10
Street NE
Calgary, AB, Canada T2E 8X2
Phone: (403) 338-6900

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Kona T0004893 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TEKTELIC Communications Kona T0004893

  • Page 1 Base model Rev D). PROPRIETARY: The information contained in this document is the property of TEKTELIC Communications Inc. Except as specifically authorized in writing by TEKTELIC, the holder of this document shall keep all information contained herein confidential, and shall protect the same in whole or in part from disclosure to all third parties.
  • Page 2 Home Sensor modules above Rev C. Oct 31, 2018 R. Nikjah Made a minor correction for PIR config registers. April 3, 2019 R. Nikjah Fixed typos. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 2 of 35...
  • Page 3: Table Of Contents

    3.4.8 Moisture Configuration................... 30 Sensor Command and Control ..................33 3.5.1 LoRaMAC Region ..................... 33 3.5.2 Command Examples ....................34 References ............................ 35 Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 3 of 35...
  • Page 4: List Of Tables

    Table 3-21: Default Values of Moisture Transducer Configuration Registers ......31 Table 3-22: Sensor Command & Control Register ............... 33 Table 3-23: LoRaMAC Regions and Region Numbers ..............33 Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 4 of 35...
  • Page 5: List Of Figures

    List of Figures Figure 2-1: The frame format in an UL payload................9 Figure 3-1: Format of a DL message.................... 11 Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 5 of 35...
  • Page 6: Acronyms And Glossary

    RFU ......reserved for future use RH ....... relative humidity RMS ......root mean square RO ....... read-only R/W ......read/write Rx ....... receiver Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 6 of 35...
  • Page 7 ....The sensing element attached to the Home Sensor, e.g. PIR transducer, humidity transducer. TRM ......technical reference manual Tx ........ transmitter UL ....... uplink Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 7 of 35...
  • Page 8: Overview

    Formation spreadsheet [2] for a thorough tool to build any UL or DL payload by varying parameter values, toggling read/write actions, and enabling/disabling different fields as desired. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 8 of 35...
  • Page 9: Ul Data Format

    0x04 Counter Number Moisture 0x09 0x00 Digital 0x00: Dry 0xFF: Wet Motion Detected 0x0A 0x00 Digital 0x00: No motion (PIR) 0xFF: Motion detected Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 9 of 35...
  • Page 10: Example Ul Payloads

    0x ���� ���� ( Motion Event Count ) = 0x 00 02 = 2 motion events 0x ���� ���� ( Break­in ) = 0x FF = break-in detected Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 10 of 35...
  • Page 11: Dl Command Format

    When a write command is sent to the Sensor, the Sensor will immediately respond with a CRC32 of the entire DL payload as the first 4 bytes of the UL frame. Note: Undefined bits/addresses are RFU and ignored. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 11 of 35...
  • Page 12: Lorawan Commissioning

    Note 2: Registers 0x02, 0x04, and 0x05 cannot be read back in some regions if the DR number is too small. For example, in the NA region, the maximum payload size with DR0 is 11 bytes. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 12 of 35...
  • Page 13: Loramac Configuration

    0x 00 04 (DR0, Tx Power 0―max power, see Table 3-4) 0x13 As per Table 3-5 0x19 0x 00 00 0x1A 0x 00 00 Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 13 of 35...
  • Page 14: Lora Config Examples

    • Set default DR number to 1 and default Tx Power number to 2: o DL payload: { 0x 92 01 02 } Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 14 of 35...
  • Page 15: Sensor Application Configuration

    PIR reports. 0x29 Ticks per External Ticks between External Input reports. A Input Tx value of 0 disables periodic External Input reports. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 15 of 35...
  • Page 16: Table 3-7: Default Values Of Periodic Transmission Configuration Registers

    ▪ Reg 22 and Reg 23 with their write bits set to true ▪ Temperature Ticks set to 1 (one) ▪ RH Ticks set to 2 (two) Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 16 of 35...
  • Page 17: Reed Switch Configuration

    High or Open), falling-edge triggered (High or Open to Closed or Low) or both. An attempt to set the Mode to 0x00 (i.e. to disable both rising and falling edges) is ignored by the Sensor. Application Example: Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 17 of 35...
  • Page 18: Table 3-9: Default Values Of Reed Switch Configuration Registers

    • Have Reed Switch be triggered only on rising edges: o DL payload: { 0x AA 01 } ▪ Reg 2A with write bit set to true Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 18 of 35...
  • Page 19: External Input Configuration

    • Door Open/Close detection would use both rising and falling triggers to detect when the door was opened and when it was closed. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 19 of 35...
  • Page 20: Table 3-11: Default Values Of External Input Configuration Registers

    3.4.3.5 Example DL Messages In the following example payloads, the Command Field is boldfaced: • Have External Input be triggered only on falling edges: Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 20 of 35...
  • Page 21: Accelerometer Configuration

    0x34 Mode Bit 0: Break-In Threshold On/Off Bit 1: Impact Threshold On/Off Bit 7: Power On/Off Other bits are ignored. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 21 of 35...
  • Page 22 The accelerator can be powered on/off to tune power usage (battery life) for end-user application. Additionally, Impact and Break-In thresholds can be enabled/disabled. Disabling a threshold prevents the Sensor from generating the applicable accelerometer event. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 22 of 35...
  • Page 23: Table 3-13: Default Values Of Accelerometer Configuration Registers

    DL payload: { 0x B4 82 B2 02 } ▪ Reg 34 and Reg 32 with their write bits set to true Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 23 of 35...
  • Page 24: Temperature/Rh Threshold Configuration

    Sample period of MCU temperature Period: Idle transducer: Idle state (seconds) 0x41 MCU Temp Sample Sample period of MCU temperature Period: Active transducer: Active state (seconds) Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 24 of 35...
  • Page 25 Thresholds Enabled bit is set. 3.4.5.6 Default Configuration Table 3-15 shows the default values for the Temperature/RH threshold configuration registers. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 25 of 35...
  • Page 26: Light Sensing Configuration

    The sensing element light pipe is visible on the top surface of the Home Sensor. The orientation of the Home Sensor relative to the light source Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 26 of 35...
  • Page 27: Table 3-16: Light Transducer Configuration Registers

    Table 3-17 shows the default values for the light transducer configuration registers. Table 3-17: Default Values of Light Transducer Configuration Registers Sample Period 0 (disabled) Threshold 1 (darkest threshold) Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 27 of 35...
  • Page 28: Motion Transducer Configuration

    Mode Bit 0: Motion State to Tx Bit 1: Motion Event Count to Tx Bit 7: PIR Sensor Enabled/Disabled Other bits are ignored. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 28 of 35...
  • Page 29: Table 3-19: Default Values Of Motion Transducer Configuration Registers

    Table 3-19: Default Values of Motion Transducer Configuration Registers Grace Period 300 seconds (5 minutes) Threshold Threshold Period 15 seconds Mode 0x81 (State Enabled, Event Count Disabled, Motion Enabled) Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 29 of 35...
  • Page 30: Moisture Configuration

    Sensor in the event of a leak, however it results in higher battery usage than a larger sample period. Supported Sample Periods are as follows: • 1: 16 seconds Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 30 of 35...
  • Page 31: Table 3-21: Default Values Of Moisture Transducer Configuration Registers

    Table 3-21 shows the default values for the moisture transducer configuration registers. Table 3-21: Default Values of Moisture Transducer Configuration Registers Sample Period 2 (32 seconds) Threshold Enable/Disable Disabled (De-initialized) Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 31 of 35...
  • Page 32 Every 60 samples, if humidity changes by more than 10% (up or down–not user configurable), the moisture detector gets recalibrated for a new dryness baseline. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 32 of 35...
  • Page 33: Sensor Command And Control

    Table 3-23. Table 3-23: LoRaMAC Regions and Region Numbers LoRaMAC Region Region Number EU868 NA915 AS923 Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 33 of 35...
  • Page 34: Command Examples

    DL payload: { 0x F0 00 01 } • Get FW version, and reset App Config to factory defaults o DL payload: { 0x 71 F2 0A} Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2 TEKTELIC Communications Inc. Confidential Page 34 of 35...
  • Page 35: References

    References [1] LoRa Alliance, "LoRaWAN Specification," ver. 1.0.3, Mar 2018. [2] TEKTELIC Communications Inc., "Kona Home Sensor Uplink and Downlink Payload Formation," ver 0.1, Jun 2018. [3] LoRa Alliance, "LoRaWAN 1.1 Regional Parameters," ver. 1.1, rev. B, Jan 2018. Kona LoRa IoT Home Sensor TRM T0005370_TRM Version 1.2...

This manual is also suitable for:

Kona t0004885Kona t0004895Kona t0004896

Table of Contents