Shark CORDLESS STRATOS IZ800 Series Quick Start Manual page 2

Please be sure to read and save the warnings on other side prior to using your unit.
How to set up the Shark IZ800 Series Shark
Vacuum with DuoClean
SETTING UP YOUR UNIT
1. Insert Wand into Floor Nozzle.
2. Insert Handheld Vacuum into wand.
3. Remove Odor Neutralizer Technology Dial from
bag. Flip up the dial handle, align the teal arrows,
then insert the dial into the nozzle. Using the
handle, rotate the dial until it clicks into the desired
intensity setting.
4. After reading it, remove the sticker from the hand
vacuum's digital screen.
For proper operation, ensure all components are
completely connected and clicked into place.
Handheld Vacuum with
Removable Battery
IZ800 Series
MultiFLEX®
DuoClean® PowerFins™
Floor Nozzle
CLEANING THE FILTERS
Regularly rinse and replace the filters to maintain
your vacuum's suction power and to maximize the
effectiveness of odor neutralization.
To clean filters, rinse them with water only. Allow
all filters to air-dry completely for up to 48 hours
before reinstalling to prevent liquid from being
drawn into electric parts.
Clean the pre-motor filters at least once a month and
post-motor filter at least once a year. Tap off loose dirt
between washes when needed. More frequent cleaning
may sometimes be necessary with heavy use.
IMPORTANT: DO NOT use soap when cleaning the filters. Use water
only. The vacuum will not have suction if the post-motor filter is not
installed. Ensure that all filters are installed before using.
QUICK START GUIDE
, PowerFins
®
2.
(Click)
Wand
1.
(Click)
ESSENTIAL MAINTENANCE ESSENTIAL MAINTENANCE
STRATOS
®
, HairPro , and Odor Neutralizer Technology.
™ ™
POWER ON/OFF
Press power button to turn vacuum
on or off.
NOTE: The unit will not turn on if the charger is
connected. Unplug the charger before turning
on vacuum power.
INSTALL ODOR DIAL IN NOZZLE
ODOR DIAL
To install the dial, align the teal
arrow on the dial with the teal arrow
on the nozzle, then insert the dial
into the nozzle. Rotate the dial
counterclockwise until it clicks into
an intensity setting to engage. Rotate
further to change the intensity setting.
For IZ862H only
CLEANING THE SENSORS
Hand Vacuum Display Panel
Fig. 1
Air path
Dust cup
Battery
CLEAN SENSE IQ SENSORS
Fig. 2
IQ logos-
both sides
Cordless MultiFLEX
™ ®
SETTINGS
SUCTION POWER MODES
Press the ( ) button to toggle
between ECO, Clean Sense IQ, and
Boost modes. To save battery power,
select ECO mode. For everyday
cleaning power, select Clean Sense
IQ mode. For an extra burst of power,
select Boost mode.
CLEAN SENSE IQ CLEAN INDICATOR
CLEAN INDICATOR
The Clean Indicator visually confirms
when floors are clean. When the unit
senses heavy debris, suction will
increase for more cleaning power.
When the debris is cleared, suction will
decrease. The clean indicator displays
the level of debris detected. For best
results, continue cleaning until the
indicator returns to its lowest level
before moving to the next area.
Make sure to clean the sensors
inside the hand vacuum regularly,
as hair and other debris may build
up and obstruct them. If the sensors
are partially obstructed, Clean
Sense IQ mode will not adjust suction levels as
expected. If the sensors are completely obstructed,
the F0 error code will appear and the Clean Sense
IQ icon will flash on the hand vacuum display panel.
To clean the sensors:
1. Turn off power and remove the hand vacuum.
2. Locate the sensors inside the nozzle of the hand
vacuum. The sensors are on the interior walls
of the nozzle, about 3 inches down the air path,
aligned with the IQ logos (Fig.2) on the exterior.
3. Gently wipe the sensors with a microfiber
cloth and remove all hair and debris.
4. Turn on power and verify that the unit is
functioning normally.
SUCTION MODE DISPLAY LIGHTS
ECO
Clean Sense IQ
Boost