AND KEEP FOR FUTURE REFERENCE. This instruction manual is designed to help you get a complete understanding of your new Shark Self-Cleaning Brushroll, DuoClean® & Powerfins™ Cordless Vacuum. If you have any questions, please call the customer service line on...
Important Safety Instructions ........4 Assembling your Shark® Vacuum Cleaner ......6 Using Your Lithium ION Power Pack Battery LED battery Power and Charging Indicators .
12 Only use Shark branded filters and ® electrical wiring, and moving parts that accessories. Damage caused by non-Shark potentially present risk to the user. filters and accessories may not be covered Before each use, carefully inspect all parts by the warranty.
Page 5
21 DO NOT use to pick up: BATTERY PACK Liquids 30. The battery is the power source for the Large objects vacuum. Carefully read and follow all Hard or sharp objects (glass, nails, charging instructions. screws, or coins) 31. To prevent unintentional starting, ensure Large quantities of dust (including the vacuum is powered off before picking drywall, fireplace ash, or embers).
ASSEMBLY 1. Insert Wand into Floor Nozzle. 2. Insert Handheld Vacuum into wand. For proper operation, ensure all components are completely connected and clicked into place. Handheld Vacuum with Removable Battery MultiFLEX® Wand DuoClean® PowerFins™ Floor Nozzle s h a r kc l e a n . c o m . a u...
LI-ION BATTERY The Lithium ION Power Pack battery does not come fully charged. Prior to first use, charge completely. During first use, run the battery down until it is completely out of power. This will condition the battery. LED BATTERY POWER AND CHARGING INDICATORS Charging Charge Charge...
CHARGING THE BATTERY USING THE LI-ION CHARGER LI-ION CHARGER IN HANDHELD VACUUM Plug the Li-Ion Charger into a wall outlet. To charge simply plug the charger into the charging port while still attached to the wand. IN THE VACUUM: MULTIFLEX® OUT OF THE VACUUM To put the vacuum in storage mode, press the The battery is removable, press and hold the...
SETTINGS POWER ON/OFF HARD FLOOR SETTING Press power button to turn on or off the vacuum. To vacuum in hard floor mode, press the floor select button until the hard floor icon ( ) illuminates. The brushrolls will spin slowly to clean bare floors and small area rugs.
CLEANING MODES UPRIGHT MODE To clean floors, place foot on floor nozzle and tilt handheld vacuum back. NOTE: Brushrolls will only engage when the handheld vacuum is tilted back. ABOVE-FLOOR HANDHELD ABOVE-FLOOR WITH WAND Press the wand release button and lift the handheld Stand the vacuum upright and press the nozzle vacuum off the wand.
USING THE MULTIFLEX® WAND MULTIFLEX® REACH Press the unlock latch on the back of the wand, Adjust the wand to a lower angle to easily clean then adjust the angle. under furniture. MULTIFLEX® STORAGE (Click) To put the vacuum in storage mode, press the To take the vacuum out of storage mode, press the unlock latch and lift up the handheld vacuum until unlock latch while folding the handheld vacuum...
MAINTAINING YOUR VACUUM EMPTYING THE DUST CUP Press the wand release button to detach the To empty the Dust Cup while it is attached to the handheld vacuum from the wand. handheld vacuum, position the dust cup over a bin and slide the lid release slider forward.
MAINTAINING YOUR VACUUM CLEANING THE FILTERS Regularly rinse and reinstall the filters to maintain your vacuum’s suction power. To clean filters, rinse them with water only. Allow all filters to air-dry completely before reinstalling to prevent liquid from being drawn into electric parts. Clean the pre-motor filters at least once a month and post-motor filter at least once a year.
MAINTAINING YOUR VACUUM FLOOR NOZZLE FLOOR NOZZLE If any hair is wrapped around the brushroll, continue cleaning using the Carpet setting on a bare floor surface, a low-pile carpet, or a small area rug. If some fibres remain wrapped around the brushroll after continued use, carefully remove them.
MAINTAINING YOUR VACUUM CHECKING FOR BLOCKAGES Checking for Blockages in the Handheld Vacuum: 1. Turn off vacuum. 2. Remove the handheld vacuum from the wand. 3. Check all intake openings on the dust cup and remove any debris or blockage. Checking for Blockages in the Wand: Standard Wand: MultiFLEX®...
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of shock and unintended operation, turn off power and remove the Lithium ION Power Pack battery before servicing. Vacuum is not picking up debris. No suction or light suction. Nozzle light is red. (Refer to Checking for Blockages section for more information.) •...
ACCESSORIES COMPATIBLE WITH THE SHARK APEX™ PRO IZ300 & IZ320 MODELS NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap of the box. To order additional accessories, visit sharkninja.com.au or sharkninja.com.nz.
• Removal of blockages. If a blockage does occur please refer to the trouble shooting guide within your Shark Operating manual • Use of parts and accessories that are not genuine Shark components s h a r kc l e a n . c o m . a u...
Need help?
Do you have a question about the Cordless APEX Pro and is the answer not in the manual?
Questions and answers