Table of Contents
Advertisement
How to maintain your automatic ice-maker
Please periodically clean to prevent the occurrence of water
scale, mold, etc. Please remove water when not making ice.
Water supply tank / Purification filter
For once-a-week
If mold forms easily in the certain types of water, clean about 2 or 3 times a week.
Take off the lid
and wash with
water.
(Temperature
tolerance
approx 60
For once-a-month
Water supply pump
Pipe
Water tank
Water suppl y pump
Take out the pipe,
Turn the cap and remove,
Pipe
Take out the impeller
and wash with water.
Impeller
※
The impeller is made with a
※
magneti c materi a l . Cl e an thoroughl y
with water, making sure there
Cap
are no substances on it.
Return parts by following the reverse procedure.
For once-a-month
Water supply pipe
Take out
the water
Water suppl y
supply tank.
tank
Water suppl y
pipe
Cleaning the ice-making tray (rinsing)
Take ice out of the
ice storage container,
close the freezer door.
Fill water supply tank
with water, put back
in original position.
Notice
Do not use washing agents such as kitchen detergents, benzene or bleach to clean the water filter. It will cause ice to have an odor.
●
If you use a bleach to clean your water supply tank or lid, please follow product directions carefully.
●
Assemble the water supply pump properly and firmly. If it is not assembled properly, it may not make ice or it may make a loud sound.
●
18
Please attach the lid of water supply tank securely. If the lid is not attached properly, the lid may be out and the water supply tank will fall.
●
Purification filter
o
C)
Pointers for assembling the water supply pump
Remove it from
tank.
If it is not assembled properly, it may not make ice or it may make
a loud sound. Please check on the following.
Turn the pump
Turn
and take out.
Turn
Pipe
Hose part
Water receptacl e
Water receptacl e
Take out
ice cubes.
Do not use a dishwasher or dryer
※
because it may cause deformation.
Remove and wash with water.
Normally, it does not need replacing.
Please replace for the following reasons:
If something other than water was put in
●
and the opening got blocked.
If it is damaged.
●
If mold, etc. is forming.
●
The claw on the cap ( )
Impeller
is turned to put onto the
protruding part ( ) of
the water supply pump.
※
①
②
Attach the water supply
Water supply tank
pump properly to the
water supply tank by
turning and attaching.
Insert the pipe into the
water supply tank opening,
Connect the pipe to the
water supply pump.
Check to make sure that there are no substances
※
Water supply tank
at the connection point of the two pipes.
Water suppl y pi p e
Take out the
water supply pipe
and wash with
Facet A
running water.
Facet B
The water receptacle
Return the water supply tank and, if does not
and hose part
sit in properly, re-set the water supply pipe.
cannot be removed.
If removal or assembly are not done correctly,
a problem such as a water leakage will occur.
Touch
for about 5 seconds.
and
will blink for about 1 minute.
The stop ice-maker light (red) will blink for about 1 minute.
●
(It rinses the ice-maker tray with water from the water supply tank.)
When light stops blinking, it will return to the previous indication.
●
Repeat
2 or 3 times.
Remove the Freezing Case (upper) discard water and ice.
Do not throw out noise reduction mat (same as p.11)
To buy another filter, please
inquire at the store where
you bought your unit.
①
②
Check to make sure that
the impeller is inside.
Return back to
original positions.
Make sure to i n sert the water
supply pipe properly so that
there's no di f ference i n surface
l e vel between facet A and facet B i s .
Freezing Case
(upper)
Advertisement
Table of Contents
