Table of Contents
Advertisement
How to maintain your automatic ice-maker
How to maintain your automatic ice-maker
Please do periodic maintenance to prevent the occurrence of water
scale, mold, etc. Please remove water when not making ice.
Water supply tank / Purification filter
For once-a-week
If mould forms easily with certain types of water, clean about 2 or 3 times a week.
Take off the lid
and wash with
water.
(Temperature
tolerance
approx 60
For once-a-month
Water supply pump
Remove pipe
Pipe
from tank.
Water tank
Turn the pump
and take out.
Water suppl y pump
Take out the pipe,
Turn the cap and remove,
Pipe
Take out the impeller
and wash with water.
Impeller
※
The impeller is made with a
※
magneti c materi a l . Cl e an thoroughl y
with water, making sure there
Cap
are no substances on it.
Return parts by following the reverse procedure.
Water supply pipe
For once-a-month
Take out
the water
Water suppl y
supply tank.
tank
Water suppl y
pipe
Cleaning the ice-making tray (rinsing)
Take ice out of the
ice storage container,
close the freezer door.
Fill water supply tank
with water, put back
in original position.
Notice
Do not use washing agents such as kitchen detergents, benzene or bleach to clean the water filter. It will cause ice to have an odor.
●
If you use a bleach to clean your water supply tank or lid, please follow product directions carefully.
●
Assemble the water supply pump properly and firmly. If it is not assembled properly, it may not make ice or it may make a loud sound.
●
Please attach the lid of water supply tank securely. If the lid is not attached properly, the lid may be out and the water supply tank will fall.
●
Purification filter
o
C)
Pointers for assembling the water supply pump
If it is not assembled properly, it may not make ice or it may make
a loud sound. Please check on the following.
Turn
②
Turn
Pipe
Water supply tank
Take out the
Hose part
water supply pipe
and wash with
running water.
Water receptacl e
Water receptacl e
The water receptacle
and hose part
cannot be removed.
Press
panel at inner back of freezer compartment.)
●
Take out
ice cubes.
●
Repeat
Remove the Freezing Case (upper) discard water and ice.
Do not throw out the noise prevention mat.
Do not use a dishwasher or dryer
※
because it may cause deformation.
Remove filter and wash with water.
Normally, it does not need replacing.
Please replace for the following reasons:
If something other than water was put in
●
and the opening got blocked.
If it is damaged.
●
If mould, etc. is forming.
●
The claw on the cap ( )
Impeller
is turned to put onto the
protruding part ( ) of
the water supply pump.
Check to make sure that
※
①
the impeller is inside.
Attach the water supply
Water supply tank
pump properly to the
water supply tank by
turning and attaching.
Insert the pipe into the
water supply tank opening,
Connect the pipe to the
water supply pump.
Check to make sure that there are no substances
※
at the connection point of the two pipes.
Water suppl y pi p e
Facet A
Facet B
Return the water supply tank and, if does not
sit in properly, re-set the water supply pipe.
If removal or assembly are not done correctly,
a problem such as a water leakage will occur.
for about 5 seconds (at temperature adjustment
The stop ice-maker light (red) will blink for about 1 minute.
(It rinses the ice-maker tray with water from the water supply tank.)
When light stops blinking, it will return to the previous indication.
2 or 3 times.
To buy another filter, please
inquire at the store where
you bought your unit.
①
②
Return back to
original positions.
Make sure to i n sert the water
supply pipe properly so that
there's no di f ference i n surface
l e vel between facet A and facet B i s .
Freezing Case
(upper)
13
Advertisement
Table of Contents
