Summary of Contents for Weber PL 814
- Page 1 PL 814 / PL814A Safety Device Operating Manual STATUS 12-2016 © Weber Lifttechnik GmbH 15.12.16 IP...
- Page 2 WEBER Lifttechnik GmbH, Fallersleber Straße. 12, D-38154 Königslutter Warranty This description has been created by WEBER Lifttechnik GmbH according to the best of their knowledge. All technical data has been carefully determined and checked and complies with the respective current status.
-
Page 3: Table Of Contents
6.3. Safety device PL814 version 2 for approach and readjustment with open doors ......11 7. Circuit diagram of the control unit ........................12 7.1. Safety circuit ............................. 12 7.2. Digital floor selection ........................13 Appendix: EU-type examination certificate Annex 1 to EU-type examination certificate EU-declaration of conformity Page 3 © Weber Lifttechnik GmbH... -
Page 4: Safety Information
1. Safety information Important preliminary remarks and safety information regarding the control units by Weber Lifttechnik GmbH The following information regarding equipping of our control units mainly contains generally valid statements. This safety information makes no claim regarding completeness. Please find special instructions regarding the handling and adjustment of the respective control unit type in the manuals included in delivery. -
Page 5: Installation And Connection Information
Figure 1: Printed circuit board PL 814 The printed circuit board PL 814 or PL814A is intended for installation in a control cabinet and is snapped on to a support rail on the assembly panel. It is to be protected against soiling, humidity and mechanical damage. -
Page 6: Safety Device Version 1 With Partial Equipping
A partially equipped circuit board can also be used for version 1 applications. For this purpose, the same circuit board is used. The partially equipped circuit board receives the designation PL814A. “6.2. Safety device version 1, partially equipped circuit board See circuit diagram PL814A” Page 6 © Weber Lifttechnik GmbH... -
Page 7: Safety Device Pl814 Version 2 For Approach And Re-Adjustment With Open Doors
PL814 bridges the door switch and the switch for the locking mechanism in the lift control units by Weber Lifttechnik GmbH. The relay –K73 (connection terminal A2) is activated via a control unit output as soon as the control unit and the absolute encoder for the shaft copying system are ready for operation. -
Page 8: Function Test
Recognition of unintentional movement of the lift car with open doors away from the stopping position and the power failure-safe storage of this fault can be executed using the circuit board PL751A, for example, which is type-tested according to EN81-1 9.11.3, EN81-2 9.13.3 or EN81-20 5.6.7.3 and 5.6.7.9. Page 8 © Weber Lifttechnik GmbH... -
Page 9: Circuit Diagram Of The Circuit Board
Weber Lifttechnik GmbH PL 814 Operating Manual 6. Circuit diagram of the circuit board 6.1. Safety device PL814 version 1 for general applications Page 9 © Weber Lifttechnik GmbH... -
Page 10: Safety Device Version 1, Partially Equipped Circuit Board Pl814A
Weber Lifttechnik GmbH PL 814 Operating Manual 6.2. Safety device version 1, partially equipped circuit board PL814A Page 10 © Weber Lifttechnik GmbH... -
Page 11: Safety Device Pl814 Version 2 For Approach And Readjustment With Open Doors
Weber Lifttechnik GmbH PL 814 Operating Manual 6.3. Safety device PL814 version 2 for approach and readjustment with open doors Page 11 © Weber Lifttechnik GmbH... -
Page 12: Circuit Diagram Of The Control Unit
Weber Lifttechnik GmbH PL 814 Operating Manual 7. Circuit diagram of the control unit 7.1. Safety circuit Page 12 © Weber Lifttechnik GmbH... -
Page 13: Digital Floor Selection
Weber Lifttechnik GmbH PL 814 Operating Manual 7.2. Digital floor selection Page 13 © Weber Lifttechnik GmbH...