Related Manuals for Doosan G250
Summary of Contents for Doosan G250
- Page 1 Synchronisation G250, G400, G500 OPERATION & MAINTENANCE MANUAL 46553375-EN (02-13) Rev. B © Doosan Company 2012 Original Instructions...
-
Page 2: Table Of Contents
ALARM HANDLING AND LOG LIST ..................27 ..........................27 LARM HANDLING ............................28 LARM LIST ..............................30 OG LIST CHECK SYNCHRONIZATION ....................30 Doosan reserves the right to change any of the above Page 2 of 32... -
Page 3: About This Document
1. About this document General purpose This document is the Operator’s Manual for Doosan PowerSource generators equipped with the synchronization option. The document mainly includes general product information, display readings, push-button and LED functions, alarm handling descriptions and presentation of the log list. -
Page 4: Warnings And Legal Information
Read this document supplied with this machine before operation or service. The installation, wiring and commissioning of Doosan generators with synchronization option can only be performed by personnel who has been duly trained by either Doosan or DEIF. The synchronization option has been developed according to the most common standards in Europe. -
Page 5: Earthing Systems
Synchronization option Operator’s Manual 3. Earthing systems Doosan reserves the right to change any of the above Page 5 of 32... - Page 6 Synchronization option Operator’s Manual Doosan reserves the right to change any of the above Page 6 of 32...
- Page 7 Synchronization option Operator’s Manual Doosan reserves the right to change any of the above Page 7 of 32...
- Page 8 Synchronization option Operator’s Manual Doosan reserves the right to change any of the above Page 8 of 32...
-
Page 9: Display Push-Buttons And Leds
Stop of the gen-set if ‘SEMI-AUTO’ or ‘MANUAL’ is selected. Manual activation of close breaker sequence if ‘SEMI-AUTO’ or ‘MANUAL’ is selected. Manual activation of open breaker sequence if ‘SEMI-AUTO’ or ‘MANUAL’ is selected. Doosan reserves the right to change any of the above Page 9 of 32... - Page 10 Selects MANUAL running mode. Like SEMI, but regulators are OFF. Selects OFF mode. All functions except protections are switched off. TEST Selects TEST RUN of the generator. Check test in Island Lamp test. Doosan reserves the right to change any of the above Page 10 of 32...
- Page 11 Tools Alarm list Silence horn Enter Step backwards GB and MB open / close AUTO mode MANUAL mode SEMI-AUTO mode OFF mode TEST mode Lamp test Doosan reserves the right to change any of the above Page 11 of 32...
-
Page 12: Led Functions
LED indicates that auto mode is selected. LED indicates that manual mode is selected. SEMI LED indicates that SEMI AUTO mode is selected. LED indicates that OFF mode is selected. Doosan reserves the right to change any of the above Page 12 of 32... - Page 13 The display LEDs are indicating as follows: Mini Announciator Engine running Generator frequency/voltage OK Generator breaker ON Mains breaker ON Alarm. AUTO mode Manual mode SEMI-AUTO OFF mode Doosan reserves the right to change any of the above Page 13 of 32...
-
Page 14: Display And Menu Structure
It can always be reached by pushing the BACK push-button 3 times. MAINS FAILURE U- supply 24.1 V 0.00I PF 0 kW 0kVA 0 kvar AGC 200 2009-09-23 08:59:08 Doosan reserves the right to change any of the above Page 14 of 32... - Page 15 Display of measured values according to the selections made during configuration. The views contains up to 20 different windows which can be selected using the push-buttons located on the right hand side of the display. Doosan reserves the right to change any of the above Page 15 of 32...
-
Page 16: Status Line Text
Gen-set running in Auto MAINS P EXPORT Gen-set stopped or running and no other action taking place MAINS P EXPORT SEMI READY MPE AUTO Gen-set stopped in Auto Doosan reserves the right to change any of the above Page 16 of 32... - Page 17 Hz/V OK IN ###s The voltage and frequency of the gen- When the timer runs out it is set is OK allowed to operate the generator breaker Doosan reserves the right to change any of the above Page 17 of 32...
- Page 18 Generator running too fast during synchronizing EXT. START ORDER A planned AMF sequence is activated There is no failure on the mains during this sequence Doosan reserves the right to change any of the above Page 18 of 32...
- Page 19 MAINS FAILURE available below 1000 G –P> Set point : -9.0% Timer: 10.2s Output A: Not used Output B: Not used Doosan reserves the right to change any of the above Page 19 of 32...
-
Page 20: Running Modes
To select another mode after the OFF mode, the password must be entered. Doosan reserves the right to change any of the above Page 20 of 32... -
Page 21: Operation Modes
Parallel Island - Analog, position 1 This mode uses the analog share line to synchronize the generators Always check the controller screen to make sure the mode is effectively activated. Doosan reserves the right to change any of the above Page 21 of 32... - Page 22 Always check the controller screen to make sure the mode is effectively activated. Please note that the mains breaker is not included in the generator supply. This has to be sourced and installed by the customer. Doosan reserves the right to change any of the above Page 22 of 32...
- Page 23 This has to be sourced and installed by the customer. For this mode, the voltage measure switch must be switched to position 2 to have the controller checking the mains voltage and frequency. Doosan reserves the right to change any of the above Page 23 of 32...
- Page 24 This has to be sourced and installed by the customer. For this mode, the voltage measure switch must be switched to position 2 to have the controller checking the mains voltage and frequency. Doosan reserves the right to change any of the above Page 24 of 32...
- Page 25 This has to be sourced and installed by the customer. For this mode, the voltage measure switch must be switched to position 2 to have the controller checking the mains voltage and frequency. Doosan reserves the right to change any of the above Page 25 of 32...
- Page 26 This has to be sourced and installed by the customer. For this mode, the voltage measure switch must be switched to position 2 to have the controller checking the mains voltage and frequency. Doosan reserves the right to change any of the above Page 26 of 32...
-
Page 27: Alarm Handling And Log List
To see the other alarms, use the push-buttons to scroll in the display. To acknowledge an alarm, place the cursor (grey area) over the channel number and then press Doosan reserves the right to change any of the above Page 27 of 32... -
Page 28: Alarm List
Non essential load trip 1880 NEL 3 P> Non essential load trip 1890 NEL 1 P>> Non essential load trip 1900 NEL 2 P>> Non essential load trip Doosan reserves the right to change any of the above Page 28 of 32... - Page 29 7640 EIC oil press. 2 CAN J1939 oil pressure 7650 EIC oil temp. 1 CAN J1939 oil temperature 7660 EIC oil temp. 2 CAN J1939 oil temperature Doosan reserves the right to change any of the above Page 29 of 32...
-
Page 30: Log List
Hint: using an analog voltmeter will make the above check much easier, the digital meters have a refresh time which makes it sometimes difficult to spot the zero volts point. Doosan reserves the right to change any of the above Page 30 of 32... - Page 31 Synchronization option Operator’s Manual Doosan reserves the right to change any of the above Page 31 of 32...
- Page 32 Synchronization option Operator’s Manual Doosan reserves the right to change any of the above Page 32 of 32...
Need help?
Do you have a question about the G250 and is the answer not in the manual?
Questions and answers