TABLE OF CONTENTS Unpacking your beverage refrigerator...2 Removing the packaging...2 Warranty Registration ...2 Installing your beverage refrigerator...3 Selecting the location...3 Cabinet Clearances ...3 Leveling legs ...3 Grounding method...3 Electrical Requirements...3 Using Your Sentry System™ Control ...4 Dimensions for 3SBARE glass door...5 Recommended Rough in Opening Dimensions for 3SBARE glass door...5...
MANUFACTURER - FILE THE CLAIM WITH THE RETAILER. If the unit was shipped or has been laying on its back for any period of time allow the refrigerator to sit upright for a period of at least 24 hours before plugging in. This will as- sure oil returns to the compressor.
For this reason it is important this area to not be obstructed and be kept clean. Marvel does not rec- ommend the use of custom made grilles as air flow may be restricted because of inadequate openings.
If you are in showcase mode, the lights will be on whether or not the door is open. Warning Alarms Your refrigerator has been fitted with a Sentry System™ refrigeration monitor. This monitor will let you know if your refrigerator is not functioning properly for optimum storage and will alert you in the unlikely event there is an unstable condition.
DIMENSIONS FOR 3SBARE GLASS DOOR Rough In Opening Dimensions, for 3SBARE Glass Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet 15” (38.1 cm) (93.98cm) 16-9/16” (39.52cm) 14-7/8” (37.78cm) 34-1/4” to 34-1/2” (87 to 87.6 cm) 3” to 3-1/4” (7.62 to 8.26cm) depth 37”...
DIMENSIONS FOR 3SBARE GLASS OVERLAY DOOR 13-29/32” (35.33cm) 14-7/8” (37.78cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) Rough In Opening Dimensions for 3SBARE Glass Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 15”...
DIMENSIONS FOR 3SBARE SOLID OVERLAY DOOR Rough In Opening Dimensions for 3SBARE Solid Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 15” (38.1 cm) 37-5/32” (94.39cm) 13-7/8” (35.26cm) 14-7/8” (37.78cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) * Depth dimension may vary depending on 23-1/4”...
25-21/32” (65.15cm) 23-7/8” (60.66cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) Rough In Opening Dimensions for 6SBARE Glass Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 24” (61 cm) DIMENSIONS FOR 6SBARE GLASS DOOR 47”...
DIMENSIONS FOR 6SBARE GLASS OVERLAY DOOR Rough In Opening Dimensions for 6SBARE Glass Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 24” (61 cm) 46-25/32 (118.82cm) 23-1/32” (58.5cm) 23-7/8” (60.66cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) * Depth dimension may vary depending on 24-1/16”...
DIMENSIONS FOR 6SBARE SOLID OVERLAY DOOR 23” (58.42cm) 23-7/8” (60.66cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) Rough In Opening Dimensions for 6SBARE Solid Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 24”...
DIMENSIONS FOR 8SBARE GLASS DOOR Rough In Opening Dimensions for 8SBARE Glass Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet 30” (76.2 cm) (134.54cm) 31-23/32” (80.57cm) 29-7/8” (75.9cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) depth 52-31/32”...
DIMENSIONS FOR 8SBARE GLASS OVERLAY DOOR 29-1/16” (73.81cm) 29-7/8” (75.9cm) 34-1/4” to 34-1/2” (87 to 87.6cm) 3” to 3-1/4” (7.62 to 8.26cm) Rough In Opening Dimensions for 8SBARE Glass Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet depth 30”...
Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side.
Page 15
1/2” (12.7)mm deep. FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS 1-23/32” Typical 4 If your refrigerator has a door lock proceed to Step 7. (38.77cm) Sides If your refrigerator does not have a door lock proceed to Step 9.
Page 16
Install the top hinge pin so the screw head is flush with the top surface of the hinge. If applicable insert key into lock and verify the lock cam works properly with the catch bracket on the front of the refrigerator cabinet. Clearance hole through door gasket channel...
Insert Wine Bottles The wine rack roll-out shelf holds four (4) bottles to ten (10) bottles of wine depending on model. See Figure 13 to 15 for typical wine bottle orientation. Loading Tips and Suggestions Your beverage center comes with sliding glass shelves and (1) wine shelf.
CARE AND CLEANING Condenser The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on adequate ventilation over the coils. Be sure that noth- ing obstructs the required air flow openings in front of the cabinet.
The 3SBARE uses one, 6 watt light tube. The 6SBARE and 8SBARE use two, 6 watt light tubes to illuminate the interior of the refrigerator. The light tube is a very reliable electrical component, but should it not function properly, please call the dealer you purchased your refrigerator from for a re- placement light tube.
• Adjust temperature warmer. (See page 12, “set the desired tempera- ture”). Allow 24 hours for tempera- ture to stabilize. • Contact a qualified Marvel service technician. • Verify cabinet is level, refer to page 3 for leveling instructions. •...
If Service is Required: • If the product is within the first year warranty period please call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, Marvel Customer Service can provide recommendations of service centers in your area.
Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material...
Page 24
Northland-Marvel P .O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011767-EN Rev J 12/05/09 www.marvelrefrigeration.com All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for...