TABLE OF CONTENTS Unpacking your refrigerator...2 Removing the packaging...2 Warranty Registration...2 Installing your refrigerator...3 Selecting the location...3 Cabinet Clearances...3 Outdoor Installation...3 Leveling legs...3 Grounding method...3 Electrical Requirements...3 Connecting the water supply...4 Using Your Refrigerator...5 Setting the temperature control...5 Defrosting instructions...5 Dimensions For 6CiM and 6OCiM Solid Door...
MANUFACTURER - FILE THE CLAIM WITH THE RETAILER. If the unit was shipped or has been laying on its back for any period of time allow the refrigerator to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor.
For this reason it is important this area to not be obstructed and be kept clean. Marvel does not rec- ommend the use of custom made grilles as air flow may be restricted because of inadequate openings.
Attach the supplied water line adapter (Figure 4) to the water valve inlet on the back of the refrigerator (See Figure 3). Be sure the rubber washer is in place in the inlet valve nut. Bend the 1/4” copper tubing to suit your installation being sure not to kink the tubing.
The higher the number you select, the cooler the temperature. (See figure 5). After loading the refrigerator allow at least 24 hours for your refrigerator to reach a new temperature setting. The refrigerator section temperature of the unit can be ad- justed using the adjusting slide located in the left side and rear of the refrigeration section.
DIMENSIONS FOR MODEL 6CiM SOLID OVERLAY DOOR (60.66cm) Recommended Rough in Opening Dimensions, 6CiM Solid Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet 24” (61 cm) 46-27/32” (119.02cm) 23-7/8” 34-1/4” to 34-1/2” 87 to 87.6cm) 3” to 3-1/4” 7.62 to 8.26cm) depth 24-1/16”...
Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side.
Page 10
3/32” (2.4mm) Diameter. Pilot Hole Softwood 5/64 (2.0mm) Diameter. Pilot Hole Table A If your refrigerator has a door lock proceed to Step 7. If your refrigerator does not have a door lock proceed to Step 9. Step 7: Mark and drill lock hole.
Install the top hinge pin so the screw head is flush with the top surface of the hinge. If applicable insert key into lock and verify the lock cam works properly with the catch bracket on the front of the refrigerator cabinet. Top hinge pin Top door hinge...
TROUBLESHOOTING YOUR REFRIGERATOR Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshoot- ing guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call.
Page 13
Items on door shelf sometimes freeze. TROUBLESHOOTING YOUR REFRIGERATOR Possible Cause • Control set too warm or cold • Temperature control slide in the refrigerator section too far open or closed. • Airflow to front grille blocked. • Excessive usage or prolonged door openings.
2 blinks, pause, 3 blinks, pause; repeated pattern. If Service is Required: • If the product is within the first year warranty period please call Marvel Customer Service at 800.223.3900 for directions on how to obtain war- ranty coverage in your area. •...
Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material...
Page 16
Northland-Marvel P .O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011768-EN Rev F 11/10/09 www.marvelrefrigeration.com All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for...
Need help?
Do you have a question about the 60CIM-SS-F and is the answer not in the manual?
Questions and answers