Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ultra Power UP1350W Touch
Summary of Contents for Ultra Power UP1350W Touch
- Page 1 UP1350W UP1350W INSTRUCTION MANUAL 1350W 1350W...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction....................Special Features..................Warning and Safety Notes................ Lithium Battery Connection Diagram............Operation Diagram - Homepage............. Operation Diagram - Setting, Start, Complete......... Battery Resistance Meter................. Lithium Battery Meter................System Set up..................Program....................Error Message..................Warranty and Service................ -
Page 3: Introduction
INTRODUCTION Thank you for purchasing UP300W Touch charger by Ultra Power. This product is a rapid charger with a high performance microprocessor and specialized operating software. Please read this entire instruction manual completely and attentively before using this product, as it covers a wide range of information on operation and safety. -
Page 4: Special Features
SPECIAL FEATURES Optimized Operating Software UP1350W Touch features the AUTO function that set the feeding current during the process of charging or discharging. Especially for lithium batteries, it can prevent the overcharging which may lead to an explosion. It can disconnect the circuit automatically and alarm once detecting any malfunction. - Page 5 SPECIAL FEATURES Terminal Voltage Control(TVC) The charger allows user to change the end voltage. Battery Internal Resistance Meter The user can check battery's total internal resistance and each cell's internal resistance. LiPo Battery Meter The user can check battery's total voltage, the highest voltage, the lowest voltage and each cell's voltage.
-
Page 6: Warning And Safety Notes
WARNING AND SAFTEY NOTE These warnings and safety notes are particularly important. Please follow the instructions for maximum safety; otherwise the charger and the battery can be damaged or at worst it can cause a fire. Also read the chapter before you begin. Never leave the charger unsupervised when it is connected to its power supply. - Page 7 WARNING AND SAFTEY NOTE Batteries installed in a device or which are electrically linked to other components Batteries that are not expressly stated by the manufacturer to be suitable for the currents the charger delivers during the charge process Please bear in mind the following points before commencing charging: Did you select the appropriate program suitable for the type of battery you are charging?
- Page 8 WARNING AND SAFTEY NOTE Charging During charge process, a specific quantity of electrical energy is fed into the battery. The charge quantity is calculated by multiplying charge current by charge time. The maximum permissible charge current varies depending on the battery type or its performance, and can be found in the information by the battery manufacturer.
- Page 9 WARNING AND SAFTEY NOTE Discharging The main purpose of discharging is to clean the residual capacity of the battery, or to reduce the battery' voltage to a defined level. The same attention should be paid to the discharging process as the charging process.
-
Page 10: Lithium Battery Connection Diagram
LITHIUM BATTERY CONNECTION DIAGRAM UP1350W Touch charger come with the built in switch mode power You can connect an external power supply (11-30V) or 12V car battery to the DC input socket. PLEASE NOTE: The charger MUST be powered before you connect a... - Page 11 6. When charging is finished disconnect the balance lead from the board, then disconnect the battery main leads from the charging lead. This diagram shows the correct way to connect your battery to the UP1350W Touch while charging in the balance charge program mode only. WARNING:...
-
Page 12: Operation Diagram - Homepage
OPERATION DIAGRAM - HOMEPAGE BATTERY TYPE ① LiPo LiFe LiIon NiMH LiHV (NiCd) SYSTEM PROGRAM BATT. IR BATT. V ② ③ ④ ① Battery Type selection buttons - Select which battery type you want charge ② SYSTEM - System setting, safety protection and charger parameter settings are here. -
Page 13: Operation Diagram - Setting, Start, Complete
OPERATION DIAGRAM - SETTING, START, COMPLETE Here are the detailed procedures to make the charger work. All the screens and operations will take Channel 1 and LiPo battery as example. 1. Battery type There are 3 Li-xx battery types in BATTERY TYPE battery type area. - Page 14 OPERATION DIAGRAM - SETTING, START, STOP Charging Program Depends on different battery type, the operation programs are different. Batt Operation Description Type Program This charging mode is for charging LiPo/LiFe/LiIon battery in normal mode. CHARGE This mode is for discharging LiPo/LiFe/LiIon battery. DISCHARGE This program is for charging or discharging lithium battery which will not be STORAGE...
- Page 15 OPERATION DIAGRAM - SETTING, START, STOP If you want change termination voltage level, please touch “MORE” to go to termination voltage level setting page. ITEM SELECTION DESCRIPTION LiPo 4.18-4.3V/Cell This is the voltage level that UP300AC Touch will stop TERMINAL charging the battery.
- Page 16 OPERATION DIAGRAM - SETTING, START, STOP LiPo 3.0-3.3V/Cell LiFe 2.6-2.9V/Cell Lilon 2.9-3.2V/Cell This is the voltage level that UP300AC Touch will stop END VOLT LiHV 3.1-3.4V/Cell discharging the battery, and is shown as volts PER CELL in DISCHARGE NiMH 0.1-1.1V/Cell the pack (not total pack voltage).
-
Page 17: Battery Resistance Meter
BATTERY RESISTANCE METER The user can check battery's total resistance, the highest resistance, the lowest resistance and each cell's resistance. Please connect the battery to the charger main battery lead to battery socket and balance wires to balance socket. BATTERY TYPE BATTERY IR 4mΩ... -
Page 18: Lithium Battery Meter
LITHIUM BATTERY METER The user can check lithium battery's total voltage, the highest voltage, the lowest voltage and each cell's voltage; and can check Nickel and Pb battery's total voltage. Touch “BATT. METER” to enter voltage meter program. BATTERY TYPE LiPo LiFe LiIon... -
Page 19: System Set Up
SYSTEM SET UP You can change SYSTEM SETTING, SAFETY OPTION settings when you enter to setting program by touch "SYSTEM". BATTERY TYPE SYSTEM BUZZER LiPo LiFe LiIon LCD LIGHT REST TIME 10min NiMH LiHV (NiCd) DISCHARGE POWER OPTION REGENERATIVE SYSTEM PROGRAM BATT. - Page 20 SYSTEM SET UP SYSTEM SYSTEM \ REGENERATIVE BUZZER WARNING: 1. USE BATTERY SOURCE LCD LIGHT REST TIME 2. JUST FOR 6P/12P Pb 10min DISCHARGE ENABLE DISABLE POWER OPTION REGENERATIVE SAFETY ABOUT BACK BACK OPTION ITEM SELECTION DESCRIPTION CAPACITY ENABLE/DISABLE CUT OFF SYSTEM SYSTEM \ SAFETY SETTING BUZZER...
-
Page 21: Program
PROGRAM BATTERY TYPE PROGRAM LiPo 2S LiPo 2S 2.0 / -1.0A 2.0 / -1.0A LiPo LiFe LiIon LiPo 2S LiPo 2S NiMH 2.0 / -1.0A 2.0 / -1.0A LiHV (NiCd) LiPo 2S LiPo 2S 2.0 / -1.0A 2.0 / -1.0A SYSTEM PROGRAM BATT. -
Page 22: Error Message
ERROR MESSAGE ERROR MESSAGE It incorporates a variety of functions for the systems to verify processes and the state of the electronics. In case of an error the screen will display the cause of error and emit an audible sound. ERROR MESSAGE EXPLANATION "... -
Page 23: Warranty And Service
WARRANTY AND SERVICE Thank you for purchasing UP1350W Touch charger by Ultra Power. We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. - Page 24 Manufactured by Ultra Power Technology Limited www.ultrapower.hk E-mail: info@ultrapower.hk...