Subscribe to Our Youtube Channel
Related Manuals for USX-MOUNT WFL009-01
Summary of Contents for USX-MOUNT WFL009-01
- Page 1 WFL009-01 INSTRUCTION MANUAL For 37-86" TV If you have any questions along the way, just give us a call 1-800-460-0956 or mail to customerservice@x-mount.com. We’re ready to help! USA-A0...
- Page 2 CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS. Before getting started, let’s check below lists to make sure it is just right for you! MAX:600mm/23.6" (MIN:200mm/7.87") Check your TV No - This mount is NOT compatible. VESA is within MAX:400mm/15.7"...
-
Page 3: Side View
TV INTERFACE MAX:600mm/23.6" MIN:200mm/7.87" MAX:400mm/15.7" 430mm/16.93" MIN:100mm/3.94" SIDE VIEW WALL PLATE 31mm/1.22" 651mm/25.63" 610.6mm/24" 535.6mm/20" 433.6mm/16" 331.6mm/12" 229.6mm/8" 158mm/6.22" 222mm/8.74" 12.5mm/0.5" 26mm/1"... - Page 4 WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
- Page 5 Parts and Hardware for STEP 2 Wall plate(Left) Lag Bolt M8x60mm M8 Washer Allen Key M5x8mm Bolt Wall plate(Right) Contact us at telephone 1-800-460-0956 (USA) or mail to customerservice@x-mount.com. to have these additional pieces shipped directly to you. Concrete Wall Anchor 4pcs...
- Page 6 1-1 Select TV Screws...
- Page 7 1-2 Figure out the suitable position of brackets HIGH MOUNTING HOLES LOW MOUNTING HOLES TV BRACKETS MUST BE LEVEL INSTALL UP/DOWN IF NEEDED...
- Page 8 1-4 Attach the TV Plate 1-3 Need Spacer? No, choose suitable screws and washers. Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle.
- Page 9 Assemble Wall plate Wall plate unit...
- Page 10 CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ●...
- Page 11 3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. 4. Install wall plate using lag bolts and washers .
- Page 12 CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly unit directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the wall plate unit on the wall at your desired height. Level the wall plate and mark the hole locations.
- Page 13 3. Insert anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using lag bolts and washers .Tighten the lag bolts only until they are pulled firmly against the wall plate. CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
- Page 14 Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly. 132lbs.(60kg)
- Page 15 Choose proper bracket section to hang pre-assembled TV unit on the TV plate at your desired position, fasten the TV brackets with the plate by tighteningthe safety screws. CAUTION: This step must require 2 or more people to finish.
- Page 16 Option 1: Choose bracket section 1 to hang TV unit on the TV plate. Option 2: Choose bracket section 2 to hang TV unit on the TV plate. Option 3: Choose bracket section 3 to hang TV unit on the TV plate. Option 1 Option 2 Option 3...
- Page 17 Pull down the straps...
Need help?
Do you have a question about the WFL009-01 and is the answer not in the manual?
Questions and answers