How-To" Maintenance; Preparation For Storage - Makita G1100 User Manual

G1100(US)_GU1835 2004.2.6 1:04 PM ページ14

9. "HOW-TO" MAINTENANCE

(See Fig. 5 5 )
1. ENGINE OIL CHANGE (See Fig. 5 5 -q q )
Change engine oil every 50 hours.
■ ■
(For new engine, change oil after 20 hours.)
(a) Drain oil by removing the drain plug and the oil
filler cap while the engine is warm.
q OIL DRAIN PLUG
(b) Reinstall the drain plug and fill the engine with oil
until it reaches the upper level on the oil filler cap.
Use fresh and high quality lubricating oil to the
■ ■
US
specified level as directed on page 6.
If contaminated or deteriorated oil is used or the
GB
quantity of the engine oil is not sufficient, the
GB
engine damage will result and its life will be
GB greatly shortened.
GB
2. SERVICING THE AIR CLEANER
GB
(See Fig. 5 5 -w w )
GB
Maintaining an air cleaner in proper condition is
very important.
GB
Dirt induced through improperly installed,
GB
improperly serviced or inadequate elements
GB
damages and wears out engines. Keep the
element always clean.
GB
(a) Unhook the cover and remove the cleaner element.
GB
q ELEMENT
GB w AIR CLEANER COVER
GB
(b) Paper element: Clean by tapping gently to
remove dirt and blow off dust. Never use oil.
GB
Clean paper element every 50 hours of
GB
operation, and replace element every 200 hours
or once a year.
(c) Urethane form : Wash the element with fresh
water. Squeeze out the water then dry the
element. (Do not twist.)
3. CLEANING AND ADJUSTING
SPARK PLUG (See Fig. 5 5 -e e ,r r )
q SPARK PLUG
w PLUG WRENCH
(a) If the plug is contaminated with carbon, remove
it using a plug cleaner or wire brush.
(b) Adjust the electrode gap to 0.6 to 0.7 mm
(0.024 to 0.028 in.).
Spark plug
14
5. CHECKING CARBON BRUSH

10. PREPARATION FOR STORAGE

(See Fig. 6 6 )
BMR4A (NGK)
(See Fig. 5 5 -t t )
If the brush become excessively worn, its contact
pressure with the slip ring changes and causes a
roughened surface on the slip ring, resulting in
irregular generator performance.
Check the brush every 500 hours or if generator
performance is irregular.
If the brush is 5 mm (0.2 in.) long or less, replace it
with a new one.
q BRUSH HOLDER
w BRUSH
e 5 mm
r M5 BOLT : 1 pc.
(a) Remove the brush cover.
(b) Disconnect the wire connector and remove the
brush.
(c) Carefully note the brush direction and relative
position with the slip ring when installing new
brush.
The following procedures should be followed
prior to storage of your generator for periods of 6
months or longer.
Drain fuel from fuel tank carefully by
■ ■
disconnecting the fuel line.
Gasoline left in the fuel tank will eventually
deteriorate making engine-starting difficult.
When draining fuel from the fuel tank, use the
■ ■
hand pomp and set it into the refilling port.
(See Fig. 6-q)
Remove the drain screw of the carburetor.
■ ■
(See Fig. 6-w)
q DRAIN SCREW
Change engine oil.
■ ■
Check for loose bolts and screws, tighten
■ ■
them if necessary.
Clean generator thoroughly with oiled cloth.
■ ■
Spray with preservative if available. NEVER
USE WATER TO CLEAN GENERATOR !
Pull starter handle until resistance is felt,
■ ■
leaving handle in that position.
Store generator in a well ventilated, low
■ ■
humidity area.