Specifications; Specification - Evince ELITE EV-ELT-948-1.0 Owner's Manual

SPECIFICATION

All units are factory programmed to the below specifications. Alteration should only be done by a factory trained technician or after consultation with one of our technical
representatives if you have any questions please contact:
Evince® Direct Phone Number: 951.734.7400
Service Related Matters: customerservice@Evincewater.com
General questions: info@Evincewater.com
Evince® Elite Automatic Water Refiners: Elite Series 1"

Specifications

Optional - High Efficiency
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
Factory Settings - Standard Capacity
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
Optional - High Capacity
Sodium Used - Per Regeneration
Water Used - Regeneration
Hardness Removal - Grains
Tank #1 EV-C12 - Cubic Feet
Tank #2 EV-UHC100 - Cubic Feet
EV-Macro Filtration Included:
EV-Clarification Included:
EV-Gold Filter included:
Tank Size
Tank Jacket / Media Loaded
Brine Tank / Cabinet Size (Inches)
Sodium Storage Capacity
Flow Rate @ 15 psi Pressure Drop
Flow Rate @ 25 psi Pressure Drop
Back Wash Flow Rate
Shipping Weight
Regeneration Type
Maximum Efficiency
Plumbing Connections
Media Type
Electrical Requirements
Water Temperature
Water Pressure
Note: Evince® Systems can be installed into homes and small commercial applications with up to 1.25" plumbing. Optional 1.25"
connections available upon request.
EV-ELT-TT-948-1.0 EV-ELT-TT-1054-1.0
3.0 lbs 4.5 lbs
92.2 gal 120.9 gal
13,000 19,500
6.0 lbs 9.0 lbs
106.5 gal 143.9 gal
19,000 28,500
12.0 lbs 18.0 lbs
109.6 gal 147.9 gal
27,000 40,500
1.0 ft 1.5 ft
1.0 ft 1.5 ft
Yes Yes
Yes Yes
Yes in Tank 2 Yes in Tank 2
9x48 10x54
Yes Yes
18.7 x 34 18.7 x 34
240 lbs 240 lbs
11.6 gpm 11.8 gpm
15.8 gpm 15.9 gpm
2.0 gpm 2.4 gpm
122 lbs 155 lbs
Dynamic Regeneration
4,333 grains /lb sodium
Includes 1" 90°Elbows & 1" Straight NPT
EV-Macro Filtration - Tank 1 and 2
EV-C12 Ultra Refiner - Tank 1
EV-Clarification - Tank 1 and 2
EV-Gold Filter - Tank 2
EV-UHC100 Hydro Conditioning - Tank 2
Input 120V 60 Hz - Output 12V 650mA
Min 39 - Max. 100 degrees Fahrenheit
Min. 20 - Max. 125 psi
EV-ELT-TT-1252-1.0 EV-ELT-TT-1354-1.0
6.0 lbs 7.5 lbs
164.9 gal 171.3 gal
26,000 32,500
12.0 lbs 15.0 lbs
190.7 gal 196.7 gal
38,000 47,500
24.0 lbs 30.0 lbs
196.8 gal 202.48 gal
54,000 67,500
2.0 ft 2.5 ft3
2.0 ft 2.5 ft3
Yes Yes
Yes Yes
Yes in Tank 2 Yes in Tank 2
12x52 13x54
No No
18.7 x 34 18.7 x 34
240 lbs 240 lbs
12.8 gpm 13.0 gpm
17.1 gpm 17.2 gpm
3.5 gpm 4.0 gpm
172 lbs 208 lbs
Working Temperature: This unit must be
operated at temperatures between 40°F and
110°F (4°C - 43°C).
Working Pressure: This water refiner must
be operated on pressures
between 30 psi to 125 psi. If the water
pressure is higher than 125 PSI, use a
pressure reducing valve in the water supply
line to the refiner.
Voltage = 120V / 60 Hz
Pipe Size = 3/4", 1" and 1.25"
• At the stated service flow rates, the
pressure drop through these devices will
not exceed 15 psig.
• The manufacturer reserves the right
to make product improvements which
may deviate from the specifications
and descriptions stated herein, without
obligation to change previously
manufactured products or to note the
change.
* Do not use water that is microbiologically
unsafe without adequate disinfection
before or after the system.
Peak flow rates intended for intermittent
use only (10 minutes or less) and are for
residential applications only. Do not use
peak flow rate for commercial applications
or for a continuous rate when treated
water supplies are geothermal heat pump,
swimming pool, etc.
For satisfactory operation, the pumping rate
of the well system must equal or exceed
indicated backwash flow rate.
All units come with plastic bypass
Maximum Iron = 1.5 ppm
Maximum Hydrogen Sulfide = 0.0 ppm
Maximum Manganese = .75 ppm
pH = 6.5 to 8.5
5