Bosch EXACT 12V-6-670 Original Instructions Manual page 17

Battery charge indicator (yellow LED)
Re- Meaning
chargeable
battery
charge
indicator (4)
Flashing Charge the battery:
light + sound You can only drive in a few more screws.
Continuous There is not enough capacity left to drive in
light + sound another screw or the power tool has over-
loaded:
The power tool can no longer be switched
on.
– Remove the battery and replace it with a
battery that is fully charged.
Flashing The power tool has overheated and
switched itself off:
light
– Wait a short while for the light to stop
flashing before switching the power tool
on again.
When the rechargeable battery (7) is inserted and the on/off
switch (8) is pressed, the battery charge indicator (4) dis-
plays the battery's state of charge for 5 seconds.
Rechargeable battery charge
indicator (4)
Green
Yellow
Red
Operating and storage conditions
The power tool is suitable only for operation at enclosed
work sites.
To ensure smooth operation, the permitted ambient temper-
ature should be between 0 °C and +45 °C, at a permitted rel-
ative humidity of between 20 and 90 %, free of condensa-
tion.
Configuring the power tool
You can configure various settings on the power tool (e.g. ro-
tational speed, screwing stage, repeat protection) using
BOSCH EXACT Configurator software of version 5.2 or
higher. The power tool must be connected to a PC via its
USB port in order to do this. Use a USB cable for this:
USB 2.0 Type A/Micro-USB 2.0 Type B
– Double-shielded
– Max. length 1 m
Note: Follow all the safety instructions and information in
the software manual.
Changing the tool (see figure B)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
Bosch Power Tools
Inserting the Application Tool
Only use application tools with the matching shank (1/4"
hexagon).
– Pull the sleeve of the quick-change chuck forwards.
– Place the application tool into the tool holder (10) and re-
lease the quick-change chuck again.
Removing the application tool
– Pull the sleeve of the quick-change chuck forwards.
– Take the application tool out of the tool holder(10) and
release the quick-change chuck again.
Operation
Starting Operation
Always set the rotational direction using the rotational direc-
tion switch (5) before starting the power tool:
The power tool will not start if the rotational direction switch
(5) is in the centre (lock-off button).
Setting the rotational direction (see figure C)
– Clockwise: To drive in screws, press the rotational direc-
tion switch (5) through as far as possible to the left.
– Anti-clockwise: To loosen or unscrew screws, press the
rotational direction switch (5) through as far as possible
Capacity
to the right.
Switching on/off
60–100 %
30–60 %
0–30 %
– To switch on the power tool, press the on/off switch (8)
down fully.
– The power tool will switch off automatically when the
set torque is reached.
If the on/off switch (8) is released too early, the pre-
u
set torque will not be reached.
Temperature Dependent Overload Protection
In the event of overload, the power tool switches off until it
returns to the optimum operating temperature range. Re-
lease the on/off switch (8) and switch the power tool back
on to continue working.
The power tool is not operated at optimum efficiency at rota-
tional speeds lower than 50 %. This may cause the temperat-
ure dependent overload protection to be activated sooner.
Set the output speed higher than 50 % or reduce the max-
imum torque used if you have problems with these settings.
Practical advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
Setting the torque (see figure D)
The torque depends on the spring preload of the shut-off
clutch. The shut-off clutch is triggered upon reaching the set
torque, both in clockwise and anticlockwise rotation.
The screwdrivers have a torque-dependent
shut-off clutch that can be set to a value in the
specified range. The clutch is triggered when
the set torque is reached.
1 609 92A 7DK | (24.11.2022)
English | 17