Unitech MS838 User Manual
  1. Manuals
  2. Brands
  3. Unitech Manuals
  4. Barcode Reader
  5. MS838
  6. User manual

Unitech MS838 User Manual

2d handheld scanner
Hide thumbs Also See for MS838:
Table of Contents

Advertisement

Quick Links

2D Handheld Scanner
- MS838 -
User's Manual
Version 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MS838 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Unitech MS838

Summary of Contents for Unitech MS838

  • Page 1 2D Handheld Scanner - MS838 - User's Manual Version 1.1...
  • Page 2 Change Log Date Change Description Version 20210202 first published version 2021/2/25 Update factory default...

  • Page 3: Preface

    –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 4 Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 5 MS838 User’s Manual European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive.
  • Page 6 MS838 User’s Manual Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either...
  • Page 7 MS838 User’s Manual Taiwan NCC Warning Statement 低功率電波輻射性電機管理辦法 第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備 之干擾。 注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響，請妥適使用。 © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 8: Laser Information

    MS838 User’s Manual Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.

  • Page 9: Battery Notice

    It may not be functional anymore. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by your warranty.
  • Page 10 If the connector is damaged, please ensure the connector is being fully repaired before use the unit to avoid causing short circuited. viii © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 11 Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction. *For applicable temperature conditions, please refer to the specification of each product. © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 12: Adapter Notice

    Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.

  • Page 13: Worldwide Support

    MS838 User’s Manual Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...

  • Page 14: Warranty Policy

    The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.

  • Page 15: Table Of Contents

    2.9 Custom Prefix..................31 2.10 Custom Suffix ..................32 2.11 Code ID ....................33 2.12 AIM ID....................34 2.13 Barcode Prefix and Suffix Order Selection .........35 xiii © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 16 A-5 Control Character Set (RS232, USB, VCP ) ........71 Appendix B – Numeric Barcodes ............72 B-1 Data and Edit barcode .................72 © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 17: Chapter 1 - Overview

    MS838 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS838 gift box. If something is missing or damaged, please contact your unitech representative. The standard package contents:  MS838 2D handheld Scanner ...

  • Page 18: Product Detail

    MS838 User’s Manual 1.2 Product Detail LED Indicator Scan Window Trigger Key - 2 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 19: Specifications

    3.7 in. x 2.7 in. x 6.2 in. (L x W x H) Dimension (95 mm x 70 mm x 160 mm) Weight 150g Trigger Switch Life 1 million time - 3 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 20 -10°C to 50°C Storage Temperature -20°C to 60°C Relative Humidity 5%-95% non-condensing IP Rating IP42 Regulatory Approvals CE, FCC, BSMI, VCCII - 4 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 21: Getting Started

    MS838 User’s Manual 1.4 Getting Started To get started with MS838, please connect USB cable to the USB port of a host PC. - 5 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 22: Led Indicator / Beeper Sequence

    Blue Blink Power on Low Tone, Middle Tone, Blue Blink High Tone Transmission error Four Low Tones No Light - 6 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 23: Chapter 2 - Command Settings

    Enable Configuration Function* Disable Configuration Function 2.1.2 Display Version Scan below bar code to display version. Display Version - 7 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 24 Scanning the below barcode can save current parameters as user ’s configuration. Save Scanning the below barcode can restore for saved user ’s configuration. Restore User Configuration - 8 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 25: Data Interface Setting

    MS838 User’s Manual 2.2 Data Interface Setting 2.2.1 USB Device Type USB Keyboard* RS232 USB Virtual Com (driver is needed) - 9 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 26: Usb Keyboard Layout

    MS838 User’s Manual 2.3 USB Keyboard Layout 2.3.1 Control Character Escaping Disable * Enable 2.3.2 Control Character Output Disable Enable - 10 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 27 2.3.3 CR/LF Character Processing (USB Keyboard) Only 0D (CR) line feed * Only 0A(LF) line feed All Covert to 0A (LF)/0D(CR) - 11 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 28 Low * Middle High Custom Sending Speed (2ms ~ 50ms) - 12 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 29 Scan below bar code to send / don’t send non printable characters to the host. Original data* Convert All to Upper Case Convert All to Lower Case Case Inversion - 13 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 30 English (US)* German French Russian (MS) Russian (typewriter) Arabic (101) Spanish Spanish (Latin America) Finnish Japanese Italian 142 Italian - 14 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 31 Polish (Programmers) Dutch (Netherlands) Czech (QWERTZ) Portuguese Portuguese (Brazil) Swedish Turkish Q Turkish F Greek (MS) French (Belgium) - 15 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 32 Please use manual to set up if encountered peculiar characters, then make sure output barcode content correctly. Auto* KOI8-R Code - 16 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 33 When output is GBK/UNICODE, the output mode will compelled to virtual keyboard. English / Latin-1 * GBK (Notepad /excel) UNICODE (Word ) - 17 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 34: Rs232 Interface Configuration

    MS838 User’s Manual 2.4 RS232 Interface Configuration 2.4.1 Baud Rate 9600 * 4800 19200 38400 57600 115200 - 18 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 35 7 Bit,2 Stop Bit, No Parity 7 Bit,2 Stop it, Even Parity B 7 Bit,2 Stop Bit, Odd Parity - 19 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 36 8 Bit,2 stop Bit, No Parity 8 Bit,2 Stop Bit, Even Parity 8 Bit,2 Stop Bit, Odd Parity - 20 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 37 Mode two or Mode three)”. Do not Replace * Replace Ç Replace Replace ^] Replace ] Replace <GS> - 21 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 38: Scan Mode

    Decoding by pulling the trigger of the scanner when auto sense mode is off. It’s default mode Off * 2.5.2 Auto Sense Mode off The scanner can sense barcode for decoding automatically. - 22 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 39 Use for decode same barcode of interval time, it will decode only one time if not exceeded set time. 750ms* 500ms - 23 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 40: Light Configuration

    MS838 User’s Manual 2.6 Light Configuration 2.6.1 LED Indicator Light On * 2.7 Buzzer Configuration 2.7.1 Volume Setting High * - 24 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 41 MS838 User’s Manual 2.7.2 Prompt Tone Setting On * 2.7.3 Successful Decode Prompt Tone Setting On * - 25 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 42 MS838 User’s Manual 2.7.4 Successful Decode Prompt Audio Frequency Setting (Tone) Custom - 26 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 43 MS838 User’s Manual 2.7.5 Successful Decode Prompt Duration Setting Long * Short - 27 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 44 There will be four consecutive error warning tones if data transmission fails, and a single error warning tone when the unrecognized configuration code is scanned. Low * Middle High - 28 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 45: Prefix And Suffix Configuration

    MS838 User’s Manual 2.8 Prefix and Suffix Configuration 2.8.1 Start Character None* - 29 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 46 MS838 User’s Manual 2.8.2 Terminal Character CR / LF* Enter None - 30 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 47: Custom Prefix

    Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) - 31 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 48: Custom Suffix

    Set Custom Suffix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) - 32 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 49: Code Id

    Set Custom Prefix (Please set up ID Table ,Data, and edit barcode refer to the appendix after scanning.) - 33 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 50: Aim Id

    MS838 User’s Manual 2.12 AIM ID 2.12.1 Output Options Off * Before Switch on After Switch on - 34 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 51: Barcode Prefix And Suffix Order Selection

    Start Character+ Custom Prefix + CODE ID+AIM ID 2.13.2 Suffix Custom Suffix+CODE ID+AIM ID+Terminal Character * CODE ID+AIM ID+Custom Suffix+Terminal Character - 35 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 52: Inverse Color Barcode Selection

    2.14 Inverse Color Barcode Selection (Only 1D/ DataMatrix / Aztec ) Normal Color Inverse Color Both (Normal / Inverse) - 36 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 53: Chapter 3 - Symbology

    (Default is switch on state) Enable All Disable All 3.1.1 Enable / Disable All 1D barcodes Enable All Disable All - 37 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 54: Codabar

    MS838 User’s Manual 3.1.2 Enable / Disable All 2D barcodes Enable All Disable All 3.2 Codabar Enable Disable - 38 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 55 Not Send Codabar Start/Terminal Character * Send Codabar Start/Terminal Character 3.2.2 Set Length Range For Codabar Minimum Length（0~50bit） Maximum Length（0~50bit） - 39 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 56: Code 39

    3.3 Code 39 Enable Disable 3.3.1 Code 39 Parity Check Disable * Enable But Not Transfer Enable & Transfer - 40 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 57 3.3.2 Code 39 Full ASCII Enable Disable * 3.3.3 Set Length Range For Code 39 Minimum Length（0~50bit） Maximum Length（0~50bit） - 41 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 58 MS838 User’s Manual 3.3.4 Code 32 (Enable code39 first ) Enable Disable 3.3.5 Code 32 Prefix Enable Disable - 42 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 59: Interleaved 2 Of 5 (Itf25)

    3.4.1 Interleaved 2 of 5 (ITF25) Check Bit Disable Check Bit * Enable Check and Not Send Check Bit Enable Check & Send Check Bit - 43 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 60 3.4.2 Interleaved 2 of 5 (ITF25) Length Selection Random Length（6-50bit）* 6 Bit 8 Bit 10 Bit 12 Bit 14 Bit 16 Bit - 44 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 61 MS838 User’s Manual 18 Bit 20 Bit 22 Bit 24 Bit - 45 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 62 MS838 User’s Manual 3.4.3 Set Length Range For Interleaved 2 of 5 Minimum Length（0~50bit） Maximum Length（0~50bit） - 46 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 63: Industrial 2 Of 5

    3.5 Industrial 2 of 5 Enable Disable 3.5.1 Set Length Range For Industrial 2 of 5 Minimum Length（0~50bit） Maximum Length（0~50bit） - 47 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 64: Matrix 2 Of 5 (4-24Bit)

    3.6 Matrix 2 of 5 (4-24bit) Enable Disable 3.6.1 Set Length Range For Matrix 2 of 5 Minimum Length（0~50bit） Maximum Length（0~50bit） - 48 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 65: Code 93

    MS838 User’s Manual 3.7 Code 93 Enable Disable 3.7.1 Set Length Range For Code 93 Minimum Length（0~50bit） Maximum Length（0~50bit） - 49 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 66: Code 11

    MS838 User’s Manual 3.8 Code 11 Enable Disable 3.8.1 Code 11 Parity Check Output Enable Disable * - 50 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 67 3.8.2 Code 11 Parity Selection Disable * 1 Bit 2 Bit 3.8.3 Set Length Range For Code 11 Minimum Length（0~50bit） Maximum Length（0~50bit） - 51 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 68: Code 128

    MS838 User’s Manual 3.9 Code 128 Enable Disable 3.9.1 Set Length Range For Code 128 Minimum Length（0~50bit） Maximum Length（0~50bit） - 52 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 69: Gs1-128

    MS838 User’s Manual 3.10 GS1-128 Enable Disable 3.11 UPC-A Enable Disable - 53 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 70 Not send UPC-A Check Bit 3.11.2 UPC-A Convert to EAN-13 Disable UPC-A convert to EAN-13 * Enable UPC-A convert to EAN-13 - 54 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 71: Upc-E

    3.12 UPC-E Enable Disable 3.12.1 UPC-E Check Bit Send UPC-E Check Bit * Not send UPC-E Check Bit - 55 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 72 MS838 User’s Manual 3.12.2 UPC-E Expand to UPC-A Enable Disable * - 56 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 73: Ean/Jan-8

    3.13 EAN/JAN-8 Enable Disable 3.13.1 EAN-8 Convert to EAN-13 Disable EAN-8 convert to EAN-13 Enable EAN-8 convert to EAN-13 - 57 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 74: Ean/Jan-13

    3.14 EAN/JAN-13 Enable Disable 3.14.1 UPC/EAN/JAN Add on code Ignore UPC/EAN/JAN * Decode UPC/EAN/JAN Custom UPC/EAN/JANA add on code - 58 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 75 MS838 User’s Manual 3.14.2 EAN13 Convert to ISBN Enable Disable * 3.14.3 EAN13 Convert to ISSN Enable Disable * - 59 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 76: Gs1 Databar (Rss14)

    3.15 GS1 DataBar (RSS14) Enable Disable 3.15.1 GS1 DataBar Limited Enable Disable 3.15.2 GS1 DataBar Expanded Enable Disable - 60 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 77: Pdf417

    MS838 User’s Manual 3.16 PDF417 Enable Disable 3.17 Micro PDF417 Enable Disable - 61 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 78: Qr Code

    MS838 User’s Manual 3.18 QR Code Enable Disable 3.19 QR Code URL Link Enable Disable - 62 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 79: Micro Qr

    MS838 User’s Manual 3.20 Micro QR Enable Disable 3.21 Data Matrix Enable Disable - 63 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 80: Aztec Code

    MS838 User’s Manual 3.22 Aztec Code Enable Disable - 64 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 81: Appendix A - Ascii Character Sets

    48  30  0  80  50  P  112  70  p  49  31  1  81  51  Q  113  71  q  - 65 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 82 125  7D  }  62  3E  >  94  5E  ^  126  7E  ~  63  3F  ?  95  5F  _  - 66 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 83: Barcode Type Id Table

    Aztec Code  7A  z  DataMatrix  75  u  PDF417  72  r  Micro PDF417  53  S  QR Code  51  Q  Micro QR Code  51  Q  - 67 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 84: Aim Id Table

    ]Em  UPC‐A/ UPC‐E  m：0，3  ISBN  ]X0  ISSN  ]X0  Aztec Code  ]z0  DataMatrix  ]dm  m: 0~6  PDF417 / Micro PDF417  ]Lm  m: 0~5  QR Code / Micro QR Code  ]Qm  m: 0~6  - 68 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 85: Control Character Set (Usb Keyboard Mode)

    F2  Ctrl+W  24  18  F3  Ctrl+X  25  19  F4  Ctrl+Y  26  1A  F5  Ctrl+Z  27  1B  F6  Ctrl+[  - 69 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 86 MS838 User’s Manual 28  1C  F7  Ctrl+\  29  1D  F8  Ctrl+]  30  1E  F9  Ctrl+^  31  1F  F10  Ctrl+_  - 70 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 87: Control Character Set (Rs232, Usb, Vcp )

    13  0D  CR  29  1D  GS  14  0E  SO  30  1E  RS  15  0F  SI  31  1F  US  - 71 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

  • Page 88: Appendix B - Numeric Barcodes

    MS838 User’s Manual Appendix B – Numeric Barcodes B-1 Data and Edit barcode - 72 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 89 MS838 User’s Manual - 73 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
  • Page 90 Cancel current setting Cancel a string of data from previous read Cancel the data from previous read Save - 74 - © 2021 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.

Table of Contents

Save PDF