Subscribe to Our Youtube Channel
Related Manuals for Besantek BST-IT706
Summary of Contents for Besantek BST-IT706
- Page 1 5kV HIGH VOLTAGE INSULATION TESTER INSTRUCTION MANUAL Test Equipment Depot - 800.517.8431 99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com...
-
Page 2: Table Of Contents
Index Page 1. Safety Precautions..........2. Overview..............3. Features..............4. Specifications............5. Connections............6. Instrument layout............ 7. Measuring procedure..........7-14 8. Charge..............9. Maintenance & repair..........10. Interface connection and operation....... 17-24... -
Page 3: Safety Precautions
1. Safety Precautions Electricity can cause severe injuries even with low voltages or currents. Therefore it is extremely important that you read the following information before using your high voltage insulation tester. a. This Instrument must only be used and operated by a competent trained person and in strict accordance with the instructions. -
Page 4: Overview
g. Rated environmental conditions: (1) Indoor use. (2) Installation Category IV . (3) Pollution Degree 2. (4) Altitude up to 2000 meters. (5) Relative humidity 80% max. (6) Ambient temperature 0 ° C~40 ° h. Observe the international Electrical Symbols listed below : lnl Meter is protected throughout by double insulation or �... -
Page 5: Features
3. Features ● 2 Lines × 16 Characters LCD ● Microprocessor-controlled ● Tests insulation resistance up to 10 TΩ ● 4 Insulation test voltages: 500V, 1000V, 2500V, 5000V ● AC/DC Voltmeter ● Short-circuit current up to 5mA ● PI (Polarization Index) indication ●... -
Page 6: Specifications
4. Specifications Test Voltage 500V, 1000V, 2500V, 5000V 1TΩ / 500V 2TΩ / 1000V Insulation resistance 5TΩ / 2500V 10TΩ / 5000V 0~100GΩ / 500V 0~200GΩ / 1000V ±(5.0%rdg + 5dgt) 0~500GΩ / 2500V 0~1000GΩ / 5000V Accuracy 100G~1TΩ / 500V 200G~2TΩ... -
Page 9: Measuring Procedure
7. Measuring procedure This tester provide five main functions and four minor functions: Main Functions: 500V voltage insulation resistance test. 1kV voltage insulation resistance test. 2.5kV voltage insulation resistance test. 5kV voltage insulation resistance test. AC/DC voltage measurement. Minor functions: Function 1 ─... - Page 11 5. Read the test value from LCD display. 6. To store the data, press @ ( ENTER/SAVE ) ; LCD displays the picture shown in below: 5451..J/0. 5KI.. 8916 00:35 & Note: When do the insulation test, always connect the test leads to the ob j ect we want to measure before pressing the TEST button.
- Page 16 (G) Introduction of other functions 1. Dielectric absorption ratio (DAR): Ratio of insulation resistance between 1-min and 30-sec 1-min insulation resistance DAR : 30-sec insulation resistance 2. Polarization index (PI): Ratio of insulation resistance between 10-min and 1-min 10-min insulation resistance PI : 1-min insulation resistance Lower insulation resistance tested takes longer test...
-
Page 17: Charge
8. Battery replacement When "Low Battery" info shows on the LCD. Disconnect the test leads from the 5kV high voltage insulation tester, and turn off the power. Replace with new Alkaline batteries.(1.5V "C" × 8) -15-... -
Page 18: Maintenance & Repair
9. Maintenance & repair (A) To avoid and electric-shock or device damage, do not wet inner part of the tester. (B) Avoid the tester from being dropped down that would damage or disconnect devices apart. (C) Wipe the tester surface with soft, dry cloth and mild detergent. -
Page 19: Interface Connection And Operation
10. Data Transmission Interface connection and operation (A) 5KV Insulation Tester Installation Steps: 1. This 5KV Insulation Tester Installation program will be installed on the computer automatically. 2. Click the “Next” key to set. 3. If you want to install a different folder, click Browse, and select another folder. - Page 20 4. Click the “Next” key. 5. It will show the information of all files are Installing to your personal computer. -18- Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 TestEquipmentDepot.co...
- Page 21 6. It will show the information of Insulation tester has been successfully installed and then click “Finish” key. (Note: If your personal computer system is Windows 7, it will indicate the driver automatically. It’s necessary to install the driver if your computer system is not windows 7, then the driver is in the compact disk (CD).
- Page 26 ⑤ Click the "Chart Display" button to see the chart, as the figure is below: This Chart Display can also show Resistance and Current diagram by clicking the dot ⑥ Click the "Save Log" button to the file, as the figure is below: -24-...
- Page 27 Test Equipment Depot - 800.517.8431 99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com...
- Page 28 T05A...
Need help?
Do you have a question about the BST-IT706 and is the answer not in the manual?
Questions and answers