Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Besantek BST-MT298
Summary of Contents for Besantek BST-MT298
- Page 1 VOLTAGE / CONTINUITY TESTER IP65 INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
Index Page 1. Introduction......2. Safety notes......3. Features........4. Specifications......5. Instrument layout...... 6. Measurement......7. Maintenance......9-10... -
Page 3: Introduction
1. Introduction Note This voltage/continuity tester has been designed and tested according to CE Safety Requirements for Electronic Measuring Apparatus, EN 61010-1, EN 61243-3, EN 61326-1 and other safety standards. Follow all warnings to ensure safe operation. Warning Read "Safety Notes" (next page) before using the voltage/continuity tester. -
Page 4: Safety Notes
2. Safety notes ● Read the following safety information carefully before attempting to operate or service the voltage tester. ● Use the voltage tester only as specified in this manual. Otherwise, the protection provided by the voltage tester may be impaired. -
Page 5: Features
3. Features ● 2000-count digital display (LCD type). ● Test leads positioned at 19mm apart. ● Interchangeable probe tip for 2mm and 4mm. ● Polarity test. ● Audible continuity test. ● Auto sensing function for: voltage (AC/DC), Ω, diode. ● Measurement function: ACV/DCV: 1000V Resistance: 2000Ω... -
Page 6: Specifications
4. Specifications Range Resolution Accuracy 1000V ±(1.3%rdg+5dgt) Range Resolution Accuracy 1000V ±(1.0%rdg+2dgt) Resistance Range Resolution Accuracy 2000Ω 1Ω ±(2.0%rdg+8dgt) Frequency Range Resolution Accuracy 30~1kHz 1Hz ±(0.5%rdg+3dgt) Continuity Buzzer sounds <200Ω... - Page 7 Voltage protection 1100V AC / DC 100V~1000V Phase rotation test measure between 2 phases, range instrument in hand Diode test 0.1~1.5V(Resolution:0.1V) Response time < 0.5s Operating temperature & 0°C ~ 40°C 80% R.H. Max. humidity Storage temperature & -10°C ~ 50°C 80% R.H. Max. humidity Probe distance 19mm apart...
-
Page 8: Instrument Layout
5. Instrument layout (1) Rubberized injection housing (2) Flashlight button (3) L2+, Red test probe (4) L1, Black test probe (5) LCD (6) Battery cover (7) Red protective cover (8) Black protective cover... -
Page 9: Measurement
6. Measurement ※ The bargraph shows the major level indication, the LCD also shows the digital reading. Before proceeding with measurement, read the safety note. WARNING! Each test 600V voltage above can only last for 1 minute. The interval between each test should be at least 5 minutes. - Page 10 3. When the battery is good, to connect the any one of test probes with a Phase Lin Point. ● How to turn off the voltage/continuity tester Separate the probes and do not touch any device, then the LCD will show “O.L.” (resistance over 2000Ω) and it will turn off after 10 seconds later.
- Page 11 In the presence of Phase (U>100V), the “ ” symbol glows. In certain cases, the “ ” symbol may light up in the presence of static charges. ● CONTINUITY TEST Performing a continuity test: Connect the test leads to the component or circuit under test.
- Page 12 ● PHASE ROTATION TEST Hold the tester's body firmly and the testing power supply sure be over 100V AC voltage (phase to phase) provided the neutral is earthed. To contact with both test electrodes (probe tips) to two phases of the three-phase power supply.
-
Page 13: Maintenance
7. Maintenance Battery replacement: When the batteries drain, change new batteries as follows: (1) Remove the screw from the battery cover. (2) Take away the battery cover and replace with new batteries. (3) Reinstall the battery cover and the screw. -11-... - Page 14 Cleaning and Storage: WARNING To avoid electrical shock or damage to the meter, do not get water inside the case. Periodically wipe the case with a damp cloth and detergent. Do not use abrasives or solvents. If the meter is not used for over 30 days, remove the batteries for storage.
Need help?
Do you have a question about the BST-MT298 and is the answer not in the manual?
Questions and answers