SubDude Audio PINWOOFER Installation Instructions Manual
Hide thumbs
Also See for PINWOOFER:
- Instructions manual (15 pages) ,
- Manual (9 pages) ,
- Instructions manual (13 pages)
Table of Contents
Advertisement
Quick Links
Copyright © 2019-2023 SubDude Audio LLC, Idaho, USA. All
Rights Reserved. Reproduction, transmission or
redistribution of this document or its contents without
written permission is prohibited.
Take your time, follow the instructions, relax, and enjoy yourself!
WARNING: Perform installation with your pinball machine turned off and unplugged from AC power.
Advertisement
Table of Contents
Related Manuals for SubDude Audio PINWOOFER
Summary of Contents for SubDude Audio PINWOOFER
- Page 1 Copyright © 2019-2023 SubDude Audio LLC, Idaho, USA. All Rights Reserved. Reproduction, transmission or redistribution of this document or its contents without written permission is prohibited. Take your time, follow the instructions, relax, and enjoy yourself! WARNING: Perform installation with your pinball machine turned off and unplugged from AC power.
- Page 2 PinWoofer JJP KOP Amplifier Installation Instructions...
-
Page 3: Amplifier Placement
Amplifier Placement Remove the Coin Box and replace it with • the amplifier resting as shown. Use only a PinWoofer supplied Amplifier • Mounting Bracket. Aside from being more secure, it will allow you to transport your machine with the amplifier installed into the bracket. -
Page 4: Harness Routing
Remove the Playfield Glass. • Lift the Playfield and prop it up. Remove the backglass. • Feed the Amplifier End of the PinWoofer • Harness down and through the Slack rectangular hole in the right side of the backbox, into the cabinet, then route the... -
Page 5: Power Connection
• Unplug the 10-Pin Factory Connector from J110, if it exists. • Plug the 10-Pin Factory Connector into the JJP Power Board. • Plug the PinWoofer Harness 2- Pin Power Connector into the Power Board. Ground Wire • Plug the Power Board into J110. -
Page 6: Audio Connection
Audio Connection • Your machine has a ground loop isolator already installed. You will re-use it. • Ensure that the Ground Loop Isolator is plugged into the green Motherboard TRS Cable Headphone Jack: Green Motherboard Extension or • This may be a Male-to-Male Headphone Jack Integrated TRS Cable Extension, or it... - Page 7 Connect Backbox Tweeters • Install your new tweeters. PinWoofer JJP Tweeter Pair • Connect the RED_BLK Tweeter Wire Pairs on to each of the left and right Tweeter Connectors as shown. • Note that JJP Tweeter / Backbox Speaker Wire colors may vary from title to title.
- Page 8 Connect Cabinet Speaker • Definitions: SVC – Single Voice Coil DVC – Dual Voice Coil • For DVC, do not alter the factory wires present on your new Cabinet Speaker. • Re-use the RED_BLK Factory Speaker Wires already present in the Harness cabinet.
-
Page 9: Speaker Connections
Unplug them now, taking careful note of their assignment (Sub/Left/Right) as denoted on the PCB. • There are different versions of the JJP Factory Sound Board so the positions of your connectors may vary. • Plug the PinWoofer Harness Speaker Connectors into the Machine Speaker Connectors as shown. • Factory Sound... - Page 10 Amplifier to Harness Connections • Insert the TRS Male Plug on the amplifier end of the PinWoofer Harness into Input TRS Jack. • Plug the 6-Pin Molex Connector into the Speaker Output Header. The Connector tab locks should Power Input Jack Speaker Output Header be facing upward.
- Page 11 When first powering on your PinWoofer Amplifier, adjust the controls as shown: • “Bass Vol” set to “6 o’clock” • All other controls set to “12 o’clock” Master Volume Power Input LED Power Indicator Speaker Output Header Backbox Treble Output TRS Jack...
- Page 12 MIX settings depending on results, and after you have had some experience with your new PinWoofer sound system. 8. Many titles have suggested initial settings at PinWoofer.com in the blog. Visit our blog at https://pinwoofer.com/blog/ or search the game title in the upper right-hand corner of the web...
-
Page 13: End Of Document
End of Document...
Need help?
Do you have a question about the PINWOOFER and is the answer not in the manual?
Questions and answers