233621 TRIP - ANC Headphones Manual

1. To turn on the earphone: press the power button for 1 seconds or above until the indicator light is on.
2. To turn off the earphone: press the power button for 3 seconds or above until the indicator light is off.
3. To switch to Noise cancelling mode: double press the power button, make sure NC switch slide to on.

1. When the earphone is off, press the power button for over 1 seconds until the yellow and the white lights blink alternatively and you will hear a voice prompt "Looking for device".
2. Activate the mobile phone Bluetooth, search and connect to the device name"233621 Trip".

1. When the earphone is off, press and hold the power button for over 5 seconds until the yellow and the white lights blink, you hear the voice prompt "Looking for Device".
2. Activate the mobile phone Bluetooth and connect.

Notice: The earphone will be powered off within 10 minutes, if there is no device connected to it. When the headset is in the pairing mode, and if there is no mobile it will prompt "Device not found", and exit the pairing mode. White Led will flash for 5 more minutes before switching on.

1. Manually disconnecting and reconnecting. The earphone will power off automatically if it is not connected to a Bluetooth device within 10 minutes.
2. Bluetooth connection when out of range
   1. The earphone which was out of the Bluetooth range will automatically reconnect if it is back in the range, within 10 minutes of disconnection.
   2. After 10 minutes, the Bluetooth will have to be manually reconnected.
   3. After 20 minutes of disconnection outside the Bluetooth range, the earphone will power off.

1. When bluetooth connected, slide the Noise cancelling switch to On/Off to turn on/off the Noise cancellation.
2. When device power on with bluetooth disconnected, noise cancelling switch slide to on status, double press power button to active "Audio disconnected, Noise cancelling", this will prevent the device power off in 10 min automatically.

1. Double tap: ambient mode on/off.
2. Triple tap: active mobile phone voice assistant.

1. When the battery power is less than 10%, the yellow indicator light will flash with voice prompt.
2. While charging, the yellow indicator light is on.
3. When fully charged, the white indicator light is on.

Notice:

1. Charge the earphone via computer or certified charger (output 5v/200mA), the earphone will be fully charged in 3 hours.
2. If the earphone is automatically turned off due to insufficient power, charge the earphone on time. If the earphone is not charged for a long time, the battery life may be affected.

1. Power on: "Power on".
2. Pairing successful: "Audio connected".
3. Pairing failure: "Device not found".
4. Low battery: "Battery low"(<10%).
5. Bluetooth pairing: "Looking for device".
6. Connection failure: "Audio disconnected".
7. Power off: "Power off".
8. Maximum valume: "Beep".
9. Incoming call when playing music: "Beep Beep" warning when there's incoming call 10. "Beep" voice after hanging up.

1. Press the power button to answer the call.
2. Long Press the power button until you hear the voice prompt, to reject the call.

1. Press the power button to hang up the call.
2. Press the "Volume+"and "Volume-" to adjust the volume

1. Press power button to put the current caller on hold and connect with the incoming call.
2. Long press the power button to continue with the current call and reject the incoming call.
3. While the call is in progress, short press the power button to hang up the ongoing call.

Notice: Some of the mobile phone brands and models may differ in operation. For queries contact sales for support.

1. Press the power button to pause.
2. Short press the "Volume+" button to turn up the volume.
3. Short press the "Volume -" button to turn down the volume.
4. Long press the"Volume +" button to play the next song.
5. Long press the "Volume -" button to play the previous song.