Related Manuals for AcSiP EK-AI7933CLD
Summary of Contents for AcSiP EK-AI7933CLD
- Page 1 EK-AI7933CLD User Guide Version 912-13903 Doc No Date 2022/11/14 AcSiP Technology Corp www.acsip.com.tw...
- Page 2 Revised Contents Revised By Version 2022/04/29 Initial Version Ivan 2022/08/25 Add FCC Statement Ivan 2022/09/26 Modify Hardware Features Ivan 2022/10/20 Add EVK Schematic Ivan 2022/11/14 Modify Hardware Features Ivan Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 1 /33...
-
Page 3: Table Of Contents
INDEX Introduction ..................4 General Description ......................4 Get started with the HDK ..............5 Configuring the EK-AI7933CLD ..................5 Installing the FTDI drivers on Microsoft Windows ............6 Hardware Features ................8 Features Description ....................... 8 Hardware Feature Configuration ............10 Microcontroller ...................... - Page 4 Table 5 GPIO pin multi-function definition ................17 Figure 1. Front view of EK-AI7933CLD ..................4 Figure 2. Jumpers and connectors on the EK-AI7933CLD ............5 Figure 3. COM port associated with the EK-AI7933CLD ............. 7 Figure 4. Default power jumper plot ..................10 Figure 5.
-
Page 5: Introduction
SRAM/ROM memory. The module also supports rich peripheral interfaces, including USB2.0, SDIO, SPI master, I2C, I2S, IR input, UART, AUXADC, PWM, and GPIOs. These features are used to download and debug a project on EK-AI7933CLD. The front view of the EK-AI7933CLD including AI7933CLD module in Figure 1. -
Page 6: Get Started With The Hdk
1) CON8 transfer USB interface to UART interface, can debug through UART, transmit, and receive a signal form PC. 2) CON8 is a USB 5V power for EK-AI7933CLD, or you can use external 5V power at J1. 3) CON6 is a USB OTG function com port. -
Page 7: Installing The Ftdi Drivers On Microsoft Windows
2.2 Installing the FTDI drivers on Microsoft Windows To configure the EK-AI7933CLD: 1) Connect the EK-AI7933CLD CON8 to the computer using a micro-USB cable. 2) Check your PC is x86 or x64 system. And download and install FTDI Windows serial port driver from Here. - Page 8 PRODUCT USER GUIDE www.acsip.com.tw Due to the com port numbers (COMx) are different at different PC. As red block in Figure 3. showed, means “CM33 UART”. Figure 3. COM port associated with the EK-AI7933CLD Product Name EK-AI7933CLD Version Doc No...
-
Page 9: Hardware Features
PRODUCT USER GUIDE www.acsip.com.tw 3. Hardware Features This section provides the main supported features of the EK-AI7933CLD. The detailed description of the features is provided in the upcoming sections. 3.1 Features Description 3.1.1 Technology and Package • AI7933CLD LGA-104 module, 32mm X 32mm X 2.7mm (Typ.) 3.1.2 Power Management and Clock Source... - Page 10 Channel assessment and WB RSSI for AFH • Supports BT/Wi-Fi coexistence 3.1.7 Miscellaneous • Embedded eFuse to store specific device information and RF calibration data • Advanced TDD mode Wi-Fi/Bluetooth coexistence scheme Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 9 /33...
-
Page 11: Hardware Feature Configuration
EK-AI7933CLD supports two types of power supply. 1) Power up with a micro-USB connector. An on-board switching regulator provides voltage of 3.3V for the EK-AI7933CLD, if the power is supplied from an on-board micro-USB connector CON8 (Figure 2). This supply can be isolated from the switching regulator using the jumpers. - Page 12 Table 1 Jumper settings for system power input through USB connection Jumper Usage Comments Use external power source to supply 5V voltage to EK-AI7933CLD External 5V power supply PCB. Pin 1 is 5V source. Pin2 is GND. DC-5V transfer to DC-3V3 current...
- Page 13 Figure 5. When using RTC mode, please note that remove jumper J2 and plug in jumper J26. Jumper JP5 should be switched to pin2 and pin3. Figure 5. Power up the HDK using an AA or AAA Battery (J25) Product Name EK-AI7933CLD Version Doc No 912-13903...
-
Page 14: Audio
Audio header for left speaker Audio header for right speaker AMIC for left channel (the microphone hole is set at back side of EK-AI7933CLD) AMIC for right channel (the microphone hole is set at back side of EK-AI7933CLD) Audio volume up button Audio volume down button Figure 6 . -
Page 15: Buttons
Force DL mode Press SW5 to trigger strapping mode (download mode…) 4.5 RGB LED As Figure7 showed, the EK-AI7933CLD has on-board RGB LEDs (U54/U56) which be controlled by SPIM interface. Please note that ensure jumper J79 and J80 are connected before using RGB LED function If you want to cascade more RGB LED, you can connect to J78 Figure 7. -
Page 16: Sd Card
4.6 SD Card The EK-AI7933CLD reserve a SD card slot to provide user to save data into a SD card. And note that there are some registers which placed need to be reworked before using SD card. Please refer to figure.6 and switch R756 to R757;... -
Page 17: Extension Connectors
4.7 Extension connectors The EK-AI7933CLD provides similar pin-out extension connectors for various sensor and device connectivity, as shown in Figure.7 and described in Table 4. The board has 46 GPIOs multiplexed with other interfaces. Depending on the use case, user can configure each I/O functionality. - Page 18 GPIO_52 J28 - 11 Note: GPIO_39 is AU_AMP_MUTE by default. When using pin headers J28-29pin, resistor R161 needs to be switched to Location of R160. Table 5 GPIO pin multi-function definition Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14...
- Page 19 0010 MSDC0_DAT1 MSDC0 Data[1] 0011 SPIM0_MOSI SPI0 (Master) Output SDIO_DAT1 0100 UART0_CTS UART0 CTS 0101 DEBUG_3 Debug Signal 3 0110 ANT_SEL3 Antenna Select 3 0111 CM33_GPIO_EINT1 CM33 EINT1 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 18 /33...
- Page 20 0010 SPIM1_SCK SPIM1 (Master) Clock 0011 I2SO_BCK I2SO BCK GPIO_B_1 0100 UART1_RX UART1 RX 0101 DEBUG_7 Debug Signal 7 0110 ANT_SEL4 Antenna Select 4 0111 CM33_GPIO_EINT5 CM33 EINT5 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 19 /33...
- Page 21 BT Debug UART TX 0010 UART0_TX UART0 TX GPIO_B_6 0011 TDMIN_BCK TDMIN BCK 0100 DMIC_DAT0 DMIC DAT0 (AUXADC) 0101 UART1_RX UART1 RX 0110 IR_IN IR RX Input 0111 CM33_GPIO_EINT10 CM33 EINT10 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 20 /33...
- Page 22 External PTA WLAN Active GPIO_B_10 0011 TDMIN_DI TDMIN DI (AUXADC) 0100 DMIC_DAT2 DMIC Data2 0101 DEBUG_14 Debug Signal 14 0110 ANT_SEL10 Antenna Select 10 0111 CM33_GPIO_EINT14 CM33 EINT14 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 21 /33...
- Page 23 0001* ADSP_JTAG_TRST DSP JTAG 0010 CM33_UART_TX CM33 UART TX 0011 UART0_TX UART0 TX GPIO_B_14 0100 SPIM0_CS_N SPIM0 CS 0101 RSVD RSVD 0110 UART1_TX UART1 TX 0111 SPIS_CS_N SPIS_CS_N Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 22 /33...
- Page 24 DSP UART TX 0010 ADSP_JTAG_TCK DSP JTAG 0011 PWM_1 PWM 1 GPIO_R_1 0100 PTA_EXT_IF_WLAN_ACT External PTA WLAN Active 0101 CONN_WF_MCU_TCK Wi-Fi N10 JTAG 0110 CM33_RSVD3 RSVD 0111 CM33_GPIO_EINT22 CM33 EINT22 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 23 /33...
- Page 25 USB OTG ID Pin 0001* USB_IDDIG 0010 I2C0_SCL I2C0 Clock 0011 PWM_5 PWM 5 GPIO_R_5 0100 I2C1_SCL I2C1 Clock 0101 RSVD RSVD 0110 DEBUG_0 Debug Signal 0 0111 CM33_GPIO_EINT26 CM33 EINT26 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 24 /33...
- Page 26 0010 CM33_UART_TX CM33 UART TX 0011 PWM_9 PWM 9 GPIO_R_9 0100 I2C0_SDA I2C0 Data 0101 CONN_BGF_MCU_TRST_B I BT N10 JTAG 0110 I2C1_SCL I2C1 Clock 0111 CM33_GPIO_EINT30 CM33 EINT30 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 25 /33...
- Page 27 RSVD 0010* DBSYS_SWCLK_TCLK CM33_SWD (Default) 0011 UART1_RX UART1 RX GPIO_T_1 0100 UART0_RX UART0 RX 0101 DSP_URXD0 DSP UART RX 0110 ANT_SEL3 Antenna Select 3 0111 CM33_GPIO_EINT1 CM33 EINT1 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 26 /33...
- Page 28 SPIM0 SCK 0010 RSVD RSVD 0011 I2C1_SCL I2C1 Clock CONN_WF_MCU_AICE_ GPIO_T_5 0100 Wi-Fi N10 SWD TCKC 0101 PWM_1 PWM 1 0110 ANT_SEL7 Antenna Select 7 0111 RSVD RSVD Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 27 /33...
- Page 29 CM33 UART TX (default) 0010 RSVD RSVD 0011 KEYPAD_KPCOL_0 KEYPAD_KPCOL_0 KPCOL_0 0100 DSP_UTXD0 DSP UART TX 0101 PWM_5 PWM 5 0110 ANT_SEL11 Antenna Select 11 0111 AUDIO_DEBUG_IN_2 AUDIO_DEBUG_IN_2 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 28 /33...
- Page 30 SPIM0 MOSI 0010 CM33_UART_RX CM33 UART RX 0011 KEYPAD_KPCOL_2 KEYPAD_KPCOL_2 CONN_BGF_MCU_AICE_ KPCOL_2 0100 BT N10 SWD TCKC 0101 PWM_7 PWM 7 0110 UART1_TX UART1 TX 0111 AUDIO_DEBUG_IN_4 AUDIO_DEBUG_IN_4 Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 29 /33...
-
Page 31: Rtc
Power Management Unit (PMU). In retention mode, the PMU is turned off while the RTC module remains powered on. The RTC module only consumes 3µA in retention mode. Product Name EK-AI7933CLD Version Doc No 912-13903... -
Page 32: Federal Communication Commission Interference Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANA Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14... - Page 33 The end user manual shall include all required regulatory information/warning as show in this manual. Limited module procedures Not applicable Trace antenna designs Not applicable RF exposure considerations Product Name EK-AI7933CLD Version Doc No 912-13903 Date 2022/11/14 Page 32 /33...
-
Page 34: Evk Schematic
The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. 6. EVK Schematic The following figure is the Schematic of EK-AI7933CLD Product Name EK-AI7933CLD Version... - Page 35 Block Diagram 5F No.5 Tai-Yuan 1st St. 5F No.5 Tai-Yuan 1st St. 5F No.5 Tai-Yuan 1st St. MediaTek Inc. MediaTek Inc. MediaTek Inc. Chupei City, Hsinchu County 30265, Taiwan, R.O.C. Chupei City, Hsinchu County 30265, Taiwan, R.O.C. Chupei City, Hsinchu County 30265, Taiwan, R.O.C. Title Title Title...
- Page 36 Base Stamp U66A SDIO_DAT3 GPIO_R_0 SDIO_DAT3 GPIO_R_0 SDIO_DAT2 GPIO_R_1 SDIO_DAT2 GPIO_R_1 SDIO_DAT1 GPIO_R_2 SDIO_DAT1 GPIO_R_2 SDIO_DAT0 GPIO_R_3 SDIO_DAT0 GPIO_R_3 SDIO_CMD GPIO_R_4 SDIO_CMD GPIO_R_4 SDIO_CLK GPIO_R_5 SDIO_CLK GPIO_R_5 GPIO_R_6 GPIO_R_6 GPIO_R_7 GPIO_R_7 GPIO_R_8 GPIO_R_8 GPIO_R_9 GPIO_R_9 GPIO_B_0 GPIO_B_0 GPIO_R_10 GPIO_R_10 GPIO_R_11 GPIO_B_1 GPIO_B_1 GPIO_R_11...
- Page 37 Arduino pin holder IC_VCCIO DC_DC_3V3 R1775 R/0ohm/0201 I2C1 SCL GPIO_B_8 EXUSB_5V R1776 R/0ohm/0201 I2C1 SDA GPIO_B_7 KEY_SYSRST_B R1777 R/0ohm/0201 C_SDIO_CLK R1778 R/0ohm/0201 MISO C_SDIO_DAT0 R1779 R/0ohm/0201 MOSI C_SDIO_DAT1 R1780 R/0ohm/0201 C_SDIO_CMD R1781 R/0ohm/0201 C_SDIO_DAT2 R1782 R/0ohm/0201 C_SDIO_DAT3 CON8 CON10 R1783 R/0ohm/0201 R/0ohm/0201 GPIO_B_5...
- Page 38 Extra USB 5V Power DC to DC 3.3V VCCIO Switch EXUSB_5V DC_DC_3V3 R/0/Ohm/0402 Silkscreen TOP Base_3V3 "Only for power supply " IC_VCCIO Base_1V8 EXUSB_5V VCCIO18 HEADER 3X1 W IP252012S-2R2ML PHYLDO_OUT CON8 JP3/DIP/P2.54 LX/SW UCE01SB3020-99R Reserve for EXT 5V HEADER 3X1 USB/5P/SMD/UCE01SB3020-99R PolyFuse-SSMD1812P110TF/16 R/0/Ohm/0402...
- Page 39 RTC Interrupt DIP1/P2.54 R736 PMU_EN_RTC_M PMU_EN_RTC EXT_PMU_EN R/300/Ohm/0402 R737 R/1M/Ohm/0402 R738 RTC_EVT R/10K/0402/1% RTC_EVT Max. input 1.8V R0402 R739 R/0/ohm/0201 R0201 Silkscreen TOP SW 4 "RTC interrupt" SW -PUSHBUTTON SW 4P/DIP/FLAT RTC_Reset V_2AA_B_I Strap (mode selection) IC_VCCIO R760 NC/10K/0402/1% R0402 GPIO_B_6 R761 NC/10K/0402/1%...
- Page 40 Main chip audio part Audio power plan Volumn key pad Level shift circuit KPROW0 KPROW2 IC_VCCIO USB_3V3 DIP1/P2.54 DIP1/P2.54 R/0/ohm/0402 EXUSB_5V Audio_VCC_5V R0402 R0402 C/0.1uF/0201 R/0/ohm/0402 R/0/ohm/0402 C0201 C0201 C/0.1uF/0201 C/0.1uF/0201 R/0/ohm/0402 AU_AMP_MUTE IOVL1 IOVC1 AU_AMP_SD SW 2 SW 3 AVCC IOVL2 IOVC2...
- Page 41 GPIO USB CON KPROW0 CON6 KPROW2 UCE01SB3020-99R R746 R/0/ohm/0402 USB/5P/SMD/UCE01SB3020-99R C_SDIO_CLK USB_IDDIG SDIO_CLK GPIO_R_5 D481 MSDC0_CLK USB_DP_P0 R747 NC/R/0/ohm/0402 A_USB_DP USB_DM_P0 Co-Pad A_USB_DM USB_ID_C R145 R/0ohm/0201 R/0ohm/0201 GPIO_T_6 KEY_SYSRST_B R147 R/0ohm/0201 R/0ohm/0201 R0201 GPIO_T_8 USB0_D+ R748 R/0/ohm/0402 R149 R/0ohm/0201 R100 R/0ohm/0201 AZ1045-02F R/0ohm/0201...