Summary of Contents for Barnstead International 1085 Series
Page 1
Type S108500 SAFE-T S10 Explosion Proof Stirrer OPERATION MANUAL SERIES 1085 UL Listed for Class I, Group C and D Hazardous Locations Model # Voltage Description S108525 100-120 10.5” X 10.5” (26.7 cm X 26.7 cm) UL Listed Ceramic Top LT1085X1 •...
Safety Information This manual contains important operating and Alert Signals safety information. You must carefully read and understand the contents of this manual prior to Warning the use of this equipment. Warnings alert you to a possibility of per- sonal injury. Your Barnstead|Thermolyne S108525 SAFE-T S10 Explosion-Proof Stirrer (UL Listed for Class I, Group C and D Hazardous Locations) has been...
AFETY NFORMATION Summary of Hazardous Atmospheres Chemicals/atmospheres designated as Class I, Group C and Group D in accordance with the National Electric Code, National Fire Protection Association (NFPA 70).* GROUP CHEMICAL/ATMOSPHERE IGNITION TEMPERATURES Acetaldehyde 175°C, 347°F Diethyl Ether 160°C, 320°F Warning Ethylene 450°C, 842°F...
Introduction Intended Use The S108525 SAFE-T S10 Stirrer is UL listed Note and has been designed to meet OSHA and The S108525 SAFE-T S10 Stirrer is other safety standards. It is intended for stirring UL listed explosion-proof for Class I, Division I, Group C and D locations in atmospheres which have an ignition temper- where flammable gases or vapors...
General Specifications SAFE-T S10 Stirrer for Hazardous Locations Model # S108525 Class Division Groups C and D Dimensions: Top Plate 10.5” x 10.5” (26.7 x 26.7 cm) Overall (W x H x D) 11.0” x 8.13” x 14.5” (27.9 x 20.8 x 36.8 cm) Weight 27 lb.
Installation Site Selection Caution Install the SAFE-T S10 Stirrer on a level, sturdy To reduce the risk of fire or explo- surface and allow space for ventilation. sion, do not install where the marked operating temperature The electrical specifications are located on the exceeds the ignition temperature of back of the stirrer.
Operation Stirring Speed Specifications Warning Speed range : 60 to1200 rpm Due to the nature of this product, operator (Maximum speed is dependent on the viscosity safety will be endangered should mainte- of the solution.) nance or servicing be performed on it. If maintenance or servicing is needed, the Stability of the stirring speed setting (4 liter stirrer must be returned to the factory.
PERATION Overcurrent Protection Warning The stirring motor in the SAFE-T S10 is equipped To prevent ignition of hazardous atmos- with an overcurrent protection device. In the pheres, the aluminum explosion-proof event that this device would be activated, the stir- enclosure chambers must be kept closed ring motor will shut off.
If maintenance or servicing is needed, the stirrer must be returned to the factory. Disconnect the unit from the supply circuit and any installation mountings and call Barnstead International cus- tomer service (1-800-553-0039 or 1-563-556- 2241). General Cleaning Instructions Wipe exterior surfaces with a slightly dampened cloth containing a mild soap solution.
All parts listed herein may be ordered from the Barnstead International dealer from whom you purchased this unit or can be obtained promptly from the factory. When service or replacement parts are needed we ask that you check first with your dealer.
USE OR PERFORMANCE OF ANY PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE), ANY THEORY OF STRICT LIABILITY OR REGULATORY ACTION. The name of the authorized Barnstead International dealer nearest you may be obtained by calling 1-800-446-6060 (563-556-2241) or writing to: 2555 Kerper Boulevard P.O.