Hover-1 FALCON-1 Operation Manual
Hide thumbs Also See for FALCON-1:

Advertisement

Quick Links

H O V E R B O A R D AT TA C H M E N T
OPERATION MANUAL
H1-F1-BGY

Advertisement

Table of Contents
loading

Summary of Contents for Hover-1 FALCON-1

  • Page 1 H O V E R B O A R D AT TA C H M E N T OPERATION MANUAL H1-F1-BGY...
  • Page 2 HELMETS SAVE LIVES! Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride. Incorrect Fit: Correct Fit: Forehead is exposed and Make sure your helmet vulnerable to serious injury. covers your forehead.
  • Page 3 INTRODUCTION This manual is designed to provide you the information you need for the safe operation and maintenance of your new Falcon-1. Please read it thoroughly before riding your Falcon-1. WARNING Make sure you read this complete manual before riding your Falcon-1.
  • Page 4: Specifications

    FALCON-1 DIAGRAM 1. Seat 2. Fog Blaster & Mount 3. Right Handlebar 4. Handlebar Mount 5. Hook and Loop Strap 6. Left Handlebar 7. Seat Frame 8. Twist Knob 9. Front Frame 10. Foot Rests 11. Caster Wheel 12. Flag 13.
  • Page 5: Parts List

    PARTS LIST 3 Pairs of Hook & Loop Straps with Rubber (1) Seat Protectors (Preassembled) Tool Set: (1) Fog Blaster Wrench Hex Key & Screwdriver (1) Charging Cable (1) Twist Knob (1) Seat Frame (4) M8 Short Screw (1) Fog Blaster Mount (4) M8 Long Screw (1) Front Frame (4) Short Screw...
  • Page 6 ASSEMBLING YOUR FALCON-1 Remove all Falcon-1 contents from the box. Ensure all contents from the “PARTS LIST” section are accounted for. 1. Locate the 2 M8 long screws, 2 large metal washers, and 4 rubber washers. Slide 1 large metal washer and 1 rubber washer onto 1 M8 long screw.
  • Page 7 2. Insert the front frame into the seat frame. Adjust the front frame to the desired length. Secure it in place by inserting the twist knob as shown below. Twist the knob clockwise to tighten it. Make sure the front frame does not move.
  • Page 8 3 Attach the fog blaster to the fog blaster mount as shown below. Screw in the 4 black short screws using the screwdriver at the end of the included hex key. Make sure the 2 larger holes of the fog blaster mount are facing forward.
  • Page 9 6. Assemble the ag by inserting one of the included ag rods into the opening in the ag fabric. Combine the remaining rods together by attaching them at the coupling points. Insert the assembled ag set into the ag tube. Your Falcon-1 is now assembled and should look like the image below.
  • Page 10 ATTACHING THE FALCON-1 TO YOUR HOVERBOARD Carefully follow the instructions on the following pages to attach the Falcon-1 to your hoverboard. Read this entire manual before riding your Falcon-1. Your Falcon-1 must be completely assembled before attaching it to your hoverboard. Please refer to the “ASSEMBLING YOUR FALCON-1”...
  • Page 11 2. Secure your Falcon-1 to your hoverboard using 2 of the included hook and loop straps. With the fastener side facing away from your hoverboard, thread the straps through the outside hole of each handlebar mount. 3. Wrap both straps underneath the hoverboard and pull them through to the other side. The rubber protective straps should be centered underneath the hoverboard, with side B facing the ground (see image below).
  • Page 12 4. WARNING: Ensure that the Falcon-1 is securely attached to the hoverboard, but do not over-tighten the hook & loop straps. 5. When your Falcon-1 is fully assembled, it should look like the image below.
  • Page 13 FOG BLASTER DIAGRAM 1. Charging Port 2. Water Tank 3. Power Button 4. LED Lights & Sound Effects Button 5. Fog Vent & LED Lights USING & MAINTAINING YOUR FOG BLASTER Before using the fog blaster, connect the included charging cable to the fog blaster’s charging port and a USB outlet (Figure 1).
  • Page 14: Before Riding

    FALCON-1 OPERATION It is important that you fully understand all the functions of your Falcon-1. If these functions are not used correctly, you will not have full control of your Hover-1 Falcon-1. Practice using the Falcon-1 at slower speeds in a flat, open area before riding the Falcon-1 in other spaces.
  • Page 15 PRE-RIDE FALCON-1 CHECKLIST Ensure that your Falcon-1 and hoverboard are in proper working order each time you ride. If a part of the Falcon-1 does not function correctly, please contact our Customer Support Center. • Ensure the battery of your hoverboard is fully charged before riding your Falcon-1.
  • Page 16: Safety Precautions

    The first rule of safe riding is to use common sense. The Falcon-1 cannot protect you in a crash, against impact, or from loss of control the way a car can. The Falcon-1 can tip over sideways or pitch you over the front wheel if you don’t ride it properly.
  • Page 17 CAUTION: RIDING IN WET WEATHER It is recommended that you do not ride your Falcon-1 in wet weather, as the electronic components of the hoverboard may be damaged if exposed to water. Stopping distances will be longer in wet conditions.
  • Page 18 2. Due to the nature of this product, the assembly pieces should be checked before every ride to avoid an accident while riding. 3. Do not make sharp turns, as you may drift and overturn the Falcon-1, which can result in injury to yourself and/or damage the unit.
  • Page 19 RIDING YOUR FALCON-1 Ensure your Falcon-1 is fully assembled and correctly attached to your hoverboard with all straps, screws, and nuts secured in place. Ensure your hoverboard is properly maintained as well. Failure to do so may result in damage to the unit, serious bodily harm, or death.
  • Page 20: Warranty

    WARRANTY For warranty information, please visit us at www.hover-1.com. Manufacturer: DGL Group, Ltd. 2045 Lincoln Highway, Edison, NJ 08817 TEL: 732-692-5000...
  • Page 21 @Hover1Rideables @RideHover1 @RideHover1 www.hover-1.com...

This manual is also suitable for:

H1-f1-bgy

Table of Contents