Advertisement
Quick Links
Advertisement
Related Manuals for Hover-1 KART
Summary of Contents for Hover-1 KART
- Page 1 KART OPERATION MANUAL HY-BUGGY...
- Page 2 HELMETS SAVE LIVES! Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you ride. Incorrect Fit: Correct Fit: Forehead is exposed and Make sure your helmet vulnerable to serious injury. covers your forehead.
- Page 3 INTRODUCTION This manual provides you the information you need for the safe operation and maintenance of your Hover-1 Kart. Please read it thoroughly before riding your Hover-1 Kart. WARNING Make sure you read this complete manual before riding your Hover-1 Kart. Even if you are an experienced rider, it is important that you read this manual to ensure your safety.
-
Page 4: Specifications
HOVER-1 KART DIAGRAM 1. Seat 2. Handlebars 3. Handlebar Mounts 4. Hook and Loop Strap 5. Seat Frame 6. Lockers 7. Front Frame 8. Foot Rests 9. Front Wheel 10. Flag 11. Flag Tube SPECIFICATIONS Compatibility: Most 6.5” hoverboards Max Supported Weight: Refer to your hoverboard’s manual... - Page 5 PARTS LIST (1) Wrench (1) Seat (2) Hex Keys (1) Seat Frame (2) Lockers (1) Front Frame (2) 8 X 38 Screws (4) M6 X 16 Screws (1) Left Handlebar (2) 8 mm Nuts (4) 6 mm Nuts (1) Right Handlebar (4) Metal Washers (2) Hook and Loop Straps (1) Flag Set...
- Page 6 ASSEMBLING YOUR HOVER-1 KART Remove all Hover-1 Kart contents from the box. Ensure all contents from the “PARTS LIST” section are accounted for. 1. Check the foam pads located underneath the handlebar mounts to ensure they are securely attached. After riding for a while, they may wear down and fall o . You can replace the foam pads with the included spare foam pads if needed.
- Page 7 2. Insert the left and right handlebar mounts into the seat frame as shown below. Align the holes of the handlebar mounts with the holes in the seat frame. Align the hole of the ag tube with the hole in the seat frame on either side.
- Page 8 Twist the nuts on clockwise. Hold the 6 mm nuts still with the wrench while turning the screws clockwise with the larger hex key to tighten the screws. Make sure all 4 screws are tightly secured. 5. Your Hover-1 Kart is now assembled and should look like the image below.
- Page 9 Carefully follow the instructions on the following pages to attach the Hover-1 Kart to your hoverboard. Read this entire manual before riding your Hover-1 Kart. Your Hover-1 Kart should be completely assembled prior to attaching it to your hoverboard. Please refer to the “ASSEMBLING YOUR HOVER-1 KART” section of the manual for assembly instructions.
- Page 10 2. Secure your Hover-1 Buggy to your hoverboard using 2 of the included hook and loop straps. With the fastener side facing away from your hoverboard, thread the straps through the outside hole of each handlebar mount. 3. Wrap the straps underneath the hoverboard and pull them through to the other side. Insert the straps into the rear hole of the handlebar mounts.
- Page 11 4. Assemble the ag by inserting one of the included ag rods into the opening in the ag fabric. Combine the remaining rods together by inserting them into each other at the coupling points. Insert the assembled ag set into the ag tube as shown below.
- Page 12 5. Your fully assembled Hover-1 Kart should be attached to your hoverboard as shown below.
-
Page 13: Before Riding
It is important that you fully understand all the functions of your Hover-1 Kart. If these functions are not used correctly, you will not have full control of your Hover-1 Kart. Practice using the Hover-1 Kart at slower speeds in a at, open area before riding the Hover-1 Kart in other spaces. WARNING Do not ride a Hover-1 Kart with a part that is damaged. - Page 14 PRE-RIDE HOVER-1 KART CHECKLIST Ensure that your Hover-1 Kart and hoverboard are in proper working order each time you ride. If a part of the Hover-1 Kart does not function correctly, please contact our Customer Support Center. • Ensure the battery of your hoverboard is fully charged before riding your Hover-1 Kart.
-
Page 15: Safety Precautions
The rst rule of safe riding is to use common sense. The Hover-1 Kart cannot protect you in a crash, against impact, or from loss of control the way a car can. The Hover-1 Kart can tip over sideways or pitch you over the front wheel if you don’t ride it properly. - Page 16 CAUTION: RIDING IN WET WEATHER It is not recommened that you ride your Hover-1 Kart in wet weather, as the electronic components of the hoverboard may be damaged if exposed to water. Stopping distances will be longer in wet conditions.
- Page 17 2. The assembly pieces should be checked before every ride to avoid an accident while riding. 3. Do not make sharp turns, as you may drift and overturn the Hover-1 Kart, which can result in injury to yourself and/or damage the unit.
- Page 18 RIDING YOUR HOVER-1 KART Ensure your Hover-1 Kart is fully assembled and correctly attached to your hoverboard with all straps, screws, and nuts secured in place. Ensure your hoverboard is properly maintained. Failure to do so may result in damage to the unit, serious bodily harm, or death.
-
Page 19: Warranty
WARRANTY For warranty information, please visit us at www.hover-1.com. Manufacturer: DGL Group, Ltd. 2045 Lincoln Highway, Edison, NJ 08817 TEL: 732-692-5000... - Page 20 @Hover1Rideables @RideHover1 @RideHover1 www.hover-1.com...
Need help?
Do you have a question about the KART and is the answer not in the manual?
Questions and answers