Operation; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-SS 405 E Operating Instructions Manual

Turn the clamp lever (14) clockwise to clamp the
saw blade.
5.2.3 Tilting the saw table (Fig. 7)
•
Undo the locking screw (5).
•
Tilt the table (7) to the left until the indicator
(17) points to the required angle value on the
scale (6).
Important: For precision work you should
fi rst carry out a trial cut and then re-adjust
the tilt angle as required.
5.2.4 Clamp-fi tting a coping saw blade (Fig.
6b-6c)
Many commercially available coping saw blades
can also be used with this machine.
•
Remove the saw blade as described in 5.2.2
•
Pass the coping saw blade down through the
table insert (18) and into the bottom holder
(8)
•
Use the supplied Hexagon key (24) to clamp-
fit the saw blade in the holder
•
Insert the saw blade into the top holder (13)
and clamp-fit with the supplied Hexagon key
•
Turn the clamp lever (14) clockwise to clamp
the saw blade

6. Operation

6.1 Please note:
•
Your saw does not cut wood automatically.
For cutting to occur, you have to guide the
wood against the blade.
•
The teeth cut only on the down stroke of the
blade.
•
You have to guide the wood slowly against
the blade because the teeth are very small.
•
Every new user needs a certain training
period. You are certain to break a number of
blades at the beginning.
•
When cutting thick timber, be particularly
careful not to bend or twist the blade. This will
help to prolong blade life.
6.2 On/Off switch (Fig. 3)
•
Press the green button to switch the saw on.
•
Press the red button to switch the machine
off.
•
Please note: The machine is equipped with a
safety switch to prevent it being switched on
again accidentally after a power failure.
Anl_TC_SS_405_E_GB_Korea.indb 10 Anl_TC_SS_405_E_GB_Korea.indb 10
GB
6.3 Blade speed regulator (Fig. 3)
The blade speed regulator allows you to set the
blade speed appropriate to the material to be cut.
6.4 Carrying out internal cuts
1. A feature of this fretsaw is that it allows you to
carry out internal cuts in a panel without
damaging it on the outside or circumference.
Warning! To avoid injury from accidental star-
ting: Before you remove or change the blade,
always set the switch to „0" position and pull
the power plug out of the socket.
2. To carry out internal cuts in a panel: Remove
the blade as described in Section 5.2.2
3. Drill a hole in the panel in question.
4. Place the panel on the saw table with the
drilled hole above the access hole.
5. Install the blade through the hole in the panel
and adjust the blade tension.
6. When you have completed the internal cuts,
remove the blade from the blade holders (as
described in Section 5.2.2) and take the pa-
nel off the table.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
- 10 -
20.07.2022 14:06:30 20.07.2022 14:06:30