The Maintenance section contains the In addition, the Scotsman ICELINQ® app allows users instructions and schedules for the sanitation and to connect to the machine via Bluetooth® to monitor, cleaning of the machine.
MC1448, MC1848, MC2148 Remote Cooled User Manual Installation: Product Specifications Location Limitations Warranty Information This ice system is made up of three parts, the ice The warranty statement for this product is provided making machine, or head; the remote condenser; and separately from this manual.
Scotsman. • 32=Electrical code. -32=208-230/60/1, -3= 208- 230/60/3 Scotsman reserves the right to make design changes and/or improvements at any time. Specifications and • A=series revision code. design are subject to change without notice.
The ice making head’s and the remote condenser’s listed condensers include a headmaster valve. refrigeration circuits must be connected. They are designed to be connected Scotsman refrigerant Ratings include the remote condenser motor, as it tubing, supplied in kits of liquid and discharge tubes.
MC1448, MC1848, MC2148 Remote Cooled User Manual Condenser and Machine Layouts .88 DIA. ELECTRICAL 29.50 in INLET 74.9 cm DISCHARGE LINE 1/2" MALE CPLG. 2.75 LIQUID LINE 3/8" MALE CPLG. 38.47 in 97.7 cm Cond. Fins 32.32 in 82.1 cm 35.72 in 90.7 cm AIR FLOW...
A triple head filter is recommended. Either the In addition, this product is designed to automatically Scotsman SSM3 taste and odor filter system, or the vary the amount of water purged based on the purity ADS-AP3 AquaPatrol system.
MC1448, MC1848, MC2148 Remote Cooled User Manual Panel Removal 1. Locate and disengage the two quarter turn captured screws at the bottom of the front panel. 2. Pull the front panel out at the bottom. 3. Lift the front panel up and off the machine. 4.
Use the following for planning the placement of the Configurations that do NOT meet these requirements condenser relative to the ice machine must receive prior written authorization from Scotsman. Location Limits - condenser location must not exceed ANY of the following limits: Do NOT: •...
MC1448, MC1848, MC2148 Remote Cooled User Manual For The Installer: Remote Condenser Locate the condenser as near as possible to the Meet all applicable building codes. interior location of the ice machine. Roof Attachment Spacing. Some unique installations have a ceiling Install and attach the remote condenser to the roof over the top of the condenser fan.
MC1448, MC1848, MC2148 Remote Cooled User Manual Line Set Routing and Brazing Do not connect the refrigerant tubing until all Note: Be sure tube and stubs are round, dress with routing and forming of the tubing is complete. swage tool if needed. Final connections requires brazing, steps must 8.
MC1448, MC1848, MC2148 Remote Cooled User Manual Plumbing Requirements Drains All models require connection to cold, potable water. A hand actuated valve within site of the machine All models require drain tubing to be attached to them. is required. There is a single 3/8” FPT inlet water There is a single ¾”...
MC1448, MC1848, MC2148 Remote Cooled User Manual Electrical The machine is not supplied with a power cord, the 1. Remove the junction box cover and route the machine must be hard-wired. power cord through the access hole and properly attach the power supply wires to the leads in the The dataplate on the back of the cabinet details junction box.
MC1448, MC1848, MC2148 Remote Cooled User Manual Final Check List: 1. Is the unit located indoors in a controlled Lower Light and Switch Panel environment? This user accessible panel provides important 2. Is the condenser located where it can receive operational information and duplicates the lights and adequate cooling air? switches on the controller.
MC1448, MC1848, MC2148 Remote Cooled User Manual Initial Start Up 1. Remove front and left side panels. Check machine 10. The display shows an H. for any packing or wires rubbing moving parts. The hot gas valves open and the harvest assist Note location of control board in upper left corner mechanisms are activated.
MC1448, MC1848, MC2148 Remote Cooled User Manual Adjustments Bridge Thickness - For the Service Tech Only Ice Bridge Thickness Measurement 1. Push and hold Off till the machine stops. Note: Indentations may be deeper on MC0322 and MC0330 1/8-3/16” 2. Remove evaporator cover. bridge 3.
The machine will fill up to that level and when it shuts process and then resume ice making. off the Bin Full indicator light will be On. Scan QR code to download the Scotsman ICELINQ™ App: Control Options Connect to this machine via Bluetooth to access additional machine operations, view error information, adjust settings, and initiate self-guided cleaning.
Preparing to Clean: cleaning solution of 6oz of Scotsman Clear 1 scale remover with 9 cups (72oz) of 105-115° F potable 1. Remove the front panel.
Page 20
18. Push and release the “ON” button to resume ice making. Want more detail? Scan QR Code to download the Scotsman IcelinQ™ App to connect to this machine via Bluetooth and access the self-guided cleaning process. Exterior Panels Fingerprints, dust and grease will require cleaning with a good quality stainless steel cleaner.
If so, remove the ice and the machine All Prodigy ELITE® models are Bluetooth® enabled should start in a few minutes. and are compatible with the Scotsman ICELINQ® app, available on both the Apple App Store and To Manually Reset the machine.
Page 22
SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 www.scotsman-ice.com 800-726-8762 17-3737-04...