Advertisement
NOZZLE MIX COMBINATION BURNER
Subject
General Information ................................................................................
Receiving and Inspection ..........................................................................
Capacities ............................................................................................
Dimensions ...........................................................................................
E.
Typical Piping Schematics........................................................................
Installation.............................................................................................
Operation..............................................................................................
Maintenance..........................................................................................
These instructions are intended to serve as guidelines covering the installation, operation, and maintenance of Hauck equipment. While
every attempt has been made to ensure completeness, unforeseen or unspecified applications, details, and variations may preclude
covering every possible contingency. WARNING: TO PREVENT THE POSSIBILITY OF SERIOUS BODILY INJURY, DO NOT USE OR
OPERATE ANY EQUIPMENT OR COMPONENT WITH ANY PARTS REMOVED OR ANY PARTS NOT APPROVED BY THE
MANUFACTURER. Should further information be required or desired or should particular problems arise which are not covered
sufficiently for the purchaser's purpose, contact Hauck Mfg. Co.
HAUCK MANUFACTURING CO., P.O. Box 90 Lebanon, PA 17042-0090 717-272-3051
1/08
NMC200 SERIES
WARNING
These instructions are intended for use only by
experienced,
qualified
personnel.
Adjustment of this equipment and its components,
by unqualified personnel, can result in fire,
explosion, severe personal injury, or even death.
www.hauckburner.com
combustion
start-up
Fax: 717-273-9882
INSTRUCTIONS
Page
2
2
3
4
9
10
12
12
NMC-9
Advertisement
Table of Contents
Related Manuals for Hauck NMC200 Series
Summary of Contents for Hauck NMC200 Series
-
Page 1: Table Of Contents
Operation…………………………………………………………………………………. Maintenance……………………………………………………………………………… These instructions are intended to serve as guidelines covering the installation, operation, and maintenance of Hauck equipment. While every attempt has been made to ensure completeness, unforeseen or unspecified applications, details, and variations may preclude covering every possible contingency. WARNING: TO PREVENT THE POSSIBILITY OF SERIOUS BODILY INJURY, DO NOT USE OR OPERATE ANY EQUIPMENT OR COMPONENT WITH ANY PARTS REMOVED OR ANY PARTS NOT APPROVED BY THE MANUFACTURER. -
Page 2: General Information
NMC burners can be controlled manually or automatically. Automatic control normally employs a Hauck Ratio Regulator for each control zone to maintain air-fuel ratio. An alternate system uses control valves in each of the fuel air lines, linking the valves to a single motor controller. -
Page 3: Capacities
Page 3 NMC-9 C. CAPACITIES... -
Page 4: Dimensions
Page 4 NMC-9 D. DIMENSIONS Figure 1. Dimensions NMC 210 – NMC 240... - Page 5 Page 5 NMC-9 Figure 2. Metric Dimensions NMC 210 – NMC 240...
- Page 6 Page 6 NMC-9 Figure 3. Dimensions NMC 260...
- Page 7 Page 7 NMC-9 Figure 4. Metric Dimensions NMC 260...
-
Page 8: Installation
Page 8 NMC-9 F. INSTALLATION 1. Furnish an opening in the furnace wall slightly larger than the outside dimensions of the refractory tile. Since NMC burners can fire in any position, they can be installed through the roof, walls or bottom of the furnace. IMPORTANT Do not disassemble the tile from the burner mounting assembly to install them separately. - Page 9 Page 9 NMC-9 IMPORTANT NMC210-230 Burners only – If the pilot and secondary air are to be in line, a 45° No. 1 spark ignited gas pilot must be used to avoid interference. Also, NMC220-230 Burners only – If the pilot and secondary air are to be in line, special consideration should be given to the method of installing the secondary line piping.
-
Page 10: Operation
13. Insert the pilot and flame detection system (if used) into the appropriate ports on the mounting plate. The use of a Hauck blast type gas pilot (either spark or manually ignited) is recommended. Ensure that the pilot is placed in the port specifically designated for it.
Need help?
Do you have a question about the NMC200 Series and is the answer not in the manual?
Questions and answers