Lexmark T650dtn Quick Reference
Lexmark t650dtn: quick start
Hide thumbs
Also See for T650dtn:
- User manual (218 pages) ,
- Technical reference manual (140 pages) ,
- Reference (104 pages)
Advertisement
Quick Links
Lexmark™ T65x
Quick Reference
Loading paper and
specialty media
Loading the 250-sheet or
550-sheet tray
1
Pull the tray out.
Note: Do not remove trays while a job prints or while Busy
appears on the display. Doing so may cause a jam.
2
Squeeze the width guide tab inward as shown, and move the
width guide to the correct position for the paper size being
loaded.
3
Unlock the length guide, squeeze the length guide tab inward
as shown, and slide the guide to the correct position for the
paper size being loaded.
Notes:
•
Use the size indicators on the bottom of the tray to help
position the guides.
•
For standard paper sizes, lock the length guide.
4
Flex the sheets back and forth to loosen them, and then fan
them. Do not fold or crease the paper. Straighten the edges on
a level surface.
5
Load the paper.
1
•
For single-sided printing, load the paper print side
facedown with the leading edge of the paper toward the
front of the tray.
Note: For print jobs using an optional StapleSmart
Finisher, place the leading edge of the paper toward the
back of the tray.
•
For two-sided or duplex printing, load the paper faceup
with the leading edge of the paper toward the back of the
tray.
Note: For print jobs using an optional StapleSmart II
Finisher, place the leading edge of the paper toward the
front of the tray.
Note: Notice the maximum fill line on the side of the tray
which indicates the maximum height for loading paper. Do
not overload the tray.
6
If necessary, adjust the paper guides to lightly touch the sides
of the stack, and lock the length guide for the paper sizes
indicated on the tray.
7
Insert the tray.
8
If a different type of paper was loaded than the type previously
loaded in the tray, then change the Paper Type setting for the
tray from the printer control panel.
TM
II
Advertisement
Related Manuals for Lexmark T650dtn
Summary of Contents for Lexmark T650dtn
-
Page 1: Quick Reference
Lexmark™ T65x Quick Reference Loading paper and specialty media Loading the 250-sheet or 550-sheet tray Pull the tray out. Note: Do not remove trays while a job prints or while Busy appears on the display. Doing so may cause a jam. -
Page 2: Loading The 2000-Sheet Tray
Loading the 2000-sheet tray Pull the tray out. Pull up and slide the width guide to the correct position for the paper size being loaded. Unlock the length guide. Push the length guide release latch to raise the length guide, slide the guide to the correct position for the paper size being loaded, and then lock the guide. - Page 3 Do not exceed the maximum stack height by forcing paper under the stack height limiter. • Do not load or close the printer while a job is printing. • Load only one size and type of media at a time.
-
Page 4: Setting The Paper Size And Paper Type
When sending a job to the printer, you can specify that you want the printer to hold the job in memory until you start the job from the printer control panel. All print jobs that can be initiated by the user at the printer are called held jobs. -
Page 5: Printing From A Flash Drive
For a confidential job, also enter a four-digit PIN. Click OK or Print, and then go to the printer to release the job. From the printer control panel, press the arrow buttons until Held jobs appears, and then press... -
Page 6: Canceling A Print Job From The Printer Control Panel
Cancel a job appears, and then press Maintaining the printer Cleaning the exterior of the printer Make sure that the printer is turned off and unplugged from the wall outlet. CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer, unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding.