Related Manuals for peerless-AV XTREME XHB652
Summary of Contents for peerless-AV XTREME XHB652
- Page 1 User Guide XTREME HIGH BRIGHT OUTDOOR DISPLAY ™ 2019-02-07 #:180-9127-2 (2020-03-16)
-
Page 2: System Installation And Electrical Requirements
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS Electrical Code Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of the National Electric Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the facility. Outlet shall be installed near the equipment and shall be easily accessible. -
Page 3: Fcc Caution
FCC CAUTION To assure continued compliance and possible undesirable interference, ferrite cores may be used when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to other peripheral devices. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rule. -
Page 4: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Read before operating equipment Thank you for purchasing our product. Before using it, please read this user guide carefully and follow the instructions for safe operation. Please keep this manual for future reference and always include it when transferring or transporting this product to a different location. - Page 5 WARNING • Never apply pressure to the exterior of the LCD screen. • If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care. • Do NOT climb on the product. • Do NOT install within five feet from a body of water. •...
-
Page 6: Table Of Contents
CONTENTS System Installation And Electrical Requirements ..................2 Electrical Code ..........................2 Power Source ..........................2 FCC Caution ...........................3 FCC Statement ..........................3 Relevant Information ........................3 General Safety Precautions ........................4 Set Up Instructions ..........................7 Parts List ............................7 Removing Cord Cover ........................8 Installing Power Cord ........................9 Installing IR Extender ........................9 Installing ALS Extender ........................9 Connecting Cords .........................10... -
Page 7: Set Up Instructions
SET UP INSTRUCTIONS Parts List Description A display B remote (batteries included) C IR extender D regional power cord E 3mm allen wrench user guide (not shown) G monitoring addendum (not shown) H technical support insert (not shown) A ( 1 ) B ( 1 ) C ( 1 ) E ( 1 ) -
Page 8: Removing Cord Cover
Removing Cord Cover Remove (2) M5 low-profile hex screws and rear cover plate using 3mm allen wrench (E). Do not disconnect lanyard. Remove (6) M5 hex screws and cord cover using 3mm allen wrench (E). lanyard 2019-02-07 #:180-9127-2 (2020-03-16) -
Page 9: Installing Power Cord
Installing Power Cord Insert female end of power cord into power port located inside the input compartment. Installing Ambient Light Sensor Installing IR Extender (Optional) (ALS) Extender (Optional) Insert the 3.5mm end of the included 5V Insert the 3.5mm end of the ALS Extender IR extender into the IR Extender port on (ACCD-ALS sold separately) into the ALS the input panel of the display. -
Page 10: Connecting Cords
2.5mm DC Power Port – Provides 12 VDC @ 2.5 A for powering locally stored extenders and source devices. 12 VDC accessory kits (ACCD-12K) are sold separately from Peerless-AV by contacting Customer Care at 800-865-2112. Accessory DC outputs are only active when display is on. - Page 11 Connecting Cords 12. USB 2.0 Data Port – Allows content to be displayed using a USB flash drive. This feature supports text, photo, audio and video. This port also serves as a service port for firmware upgrades. This port should not be used for powering 5 VDC devices. 13.
-
Page 12: Replacing Cord Cover
Replacing Cord Cover Run power and signal cords through notches. To prevent unwanted interference, route the power cord through the right most notch (see image 1 below). Place the cord cover over the cords being careful not to pinch any of the cords. Loosely install (6) M5 hex cap screws then tighten screws on the cord cover using 3mm allen wrench (E) until the gasket on the cover is fully compressed to the cord gasket . -
Page 13: Removing Handle Hardware
Removing Handle Hardware Optional: If removing handles, do not replace hardware. CAUTION Failure to follow these instructions can result in the product being damaged or destroyed, voiding the warranty. Connect To The Power Source Connect power cord to GFCI outlet. 2019-02-07 #:180-9127-2 (2020-03-16) -
Page 14: Prepare The Display For Mounting
Install cords prior to mounting your display. Input panel may be obstructed once the display is mounted. A mounting solution is sold separately. Contact your Peerless-AV representative for an outdoor rated mounting solution for your particular application. For your safety, only install an outdoor-rated mount that is suitable for the application and supports the weight of the display. - Page 15 Prepare The Display For Mounting Part 58.68" 34.08" 56.24" 31.64" 64.53" XHB652 (1491mm) (866mm) (1429mm) (804mm) (1639mm) FRONT VIEW 1.57" (40mm) .63" (16mm) 1.22" (31mm) .33" (8mm) .79" (20mm) 1.22" (31mm) BEZEL / IR DETAIL VIEW 2019-02-07 #:180-9127-2 (2020-03-16)
-
Page 16: Remote Control Battery Installation And Replacement
STOP GUIDE PAUSE STOP GUIDE PAUSE GUIDE or bursting. Peerless-AV recommends the following battery use: • Do not mix battery brands. • Do not combine new and old batteries. This can shorten the battery life or cause battery acid leaks. -
Page 17: Operating Instructions
OPERATING INSTRUCTIONS Power On/Off The Display Power on your display by using the remote control or the power button on the side of the display. The display will power on but image may not appear for several seconds as it completes its power up sequence. -
Page 18: Navigating The On-Screen Menu
Navigating The On Screen Menu Channel Picture Air / Cable Choose between antenna Picture Mode Theater and cable Personal Standard Auto Scan Searches for available Dynamic channels Color Temp. Normal Favorite Shows favorite channels Warm Show/Hide Show or hide channels Personal Cool DTV Signal Displays channel info and... -
Page 19: Time
Navigating The On Screen Menu Time Setup Sleep Timer off 60 min Menu Languages English 5 min 90 min Spanish 10 min 120 min French 15 min 180 min German 30 min 240 min Italian Russian Time Zone Atlantic Pacific Eastern Alaska Transparent... -
Page 20: Lock
Navigating The On Screen Menu Lock System Lock Enter Password to enter System Lock settings Defaut Password: 0000 Change Allows the password to be password changed System Lock On / Off Input Block TV, AV, Component, DP, HDMI 1, HDMI 2, HDMI 3, PC, USB US TV, MPAA Canada Canadian English,... -
Page 21: Usb Functionality
USB Functionality Insert USB flash drive into USB 2.0 Data Select USB source to access content. port on the input panel of the display. Input Source Component HDMI1 HDMI2 HDMI3 USB 2.0 Data 2019-02-07 #:180-9127-2 (2020-03-16) - Page 22 USB Functionality Select media type and folder where content is stored. PHOTO MUSIC MOVIE TEXT PHOTO MUSIC MOVIE TEXT Return Return Photos – To view a single photo, Movies – To view a single video, select photo and press play. To view select video and press play.
-
Page 23: (Rs-232C) Serial Control Of The Display
(RS-232C) Serial Control Of The Display Attach an RS-232C cable (straight through type) to the RS-232C input to utilize serial control function. Control via RS232 should only be utilized by experts familiar with RS232 programing. Menu: A0, F0, 55, FF, 4E, B1 Mute: A0, F0, 55, FF, 14, EB Right:... -
Page 24: Maintenance
MAINTENANCE Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch, mark, or even damage the screen permanently. Ensure that the display is installed in a location where it will be safe from abrasives and flying debris, which could damage the LCD panel. - Page 25 Clean Fan Filter Remove cover. Clean fan filter by running Replace filter and cover. under water until clean. XHB652 2019-02-07 #:180-9127-2 (2020-03-16)
- Page 26 This page intentionally left blank. 2019-02-07 #:180-9127-2 (2020-03-16)
- Page 27 This page intentionally left blank. 2019-02-07 #:180-9127-2 (2020-03-16)
-
Page 28: Warranty
Garantia TÜR Garanti̇ Garanzia Záruka www.peerless-av.com/warranty Peerless-AV Peerless-AV Europe Peerless-AV América Latina 2300 White Oak Circle Unit 3 Watford Interchange, Av. de las Industrias 413 Aurora, IL 60502 Colonial Way, Watford, Herts, Parque Industrial Escobedo Email: tech@peerlessmounts.com WD24 4WP, United Kingdom General Escobedo N.L., México 66062...