Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MST FXX-D S
Summary of Contents for MST FXX-D S
- Page 2 FXX-D S TOOLS Necessary tools and accessories for [ FXX D S ] assembly 需求工具及配件 & ACCESSORIES 10 DRIFT CHASSIS NECESSARY TOOLS FOR ASSEMBLY 工具需求 ( NOT INCLUDED IN KIT ) 另購 1.27 0.05 L Wrench ” 0.05 ” 板手...
-
Page 3: Parts Bag
Alum. suspension mount (+0.5) (+0.5) 鋁合金下擺臂座 210321 suspension balls 2.5 × 5 is required ※ M3 × 10 for Alum. suspension mount installing. side opening M3 × 8 ESC plate (210321) M3 × 8 以上搭配 插銷球頭才可使用￮ M3 × 8 FXX-D S... - Page 4 M3 × 12 screw × 2 圓頭螺絲 OPTIONAL PARTS 820037 suspension mount (+0.5) Alum. suspension mount (+0.5) 鋁合金下擺臂座 (+0.5) M3 × 8 210321 suspension balls 2.5 × 5 is required ※ for Alum. suspension mount installing. (210321) 以上搭配 插銷球頭才可使用￮ FXX-D S...
-
Page 5: Steering Arm
4.8 × 4.5 copper ball connector × 2 5 × 8 × 2.5 銅製球頭螺絲 spacer 3 × 5.8 × 3 spacer × 1 墊片 5 × 8 × 2.5 spacer × 4 墊片 OPTIONAL PARTS 210388 FXX Carbon steering joint plate 2.5 碳纖維轉向連接板 FXX-D S... - Page 6 M2.5 × 6 壓入 ADDITIONAL PURCHASE 5.8 ball connector Caster block E 球頭 5.8 ball connector 上擺臂墊片 Caster block F Upper arm 上擺臂墊片 前上擺臂 210061 HT Upper arm spacer M3 × 25 上擺臂墊片組 Tools upper arm C 工具 FXX-D S...
-
Page 7: Motor Mount
3 × 7 M3 × 6 自攻沉頭螺絲 STEP 3 Attaching front upper arm M2 × 3 screw × 4 安裝前上擺臂 十字螺絲 OPTIONAL PARTS 2.5 × 20 arm shaft 210340 M2 × 3 FXX Alum. motor mount set 鋁合金馬達座組 FXX-D S... - Page 8 培林 M2 × 8 screw × 1 圓頭螺絲 半牙 M2 × 8 5 × 10 ball bearing × 2 M3 × 8 screw × 2 3 × 6 × 0.5 spacer 培林 M3 × 8 圓頭螺絲 FXX-D S...
- Page 9 鋁合金下擺臂座 210321 suspension balls 2.5 × 5 is required ※ Adjust for proper space. for Alum. suspension mount installing. 2.5 × 1 shaft bush 請調整至適當的齒隙。 M3 × 10 M3 × 8 (210321) 以上搭配 插銷球頭才可使用￮ 4.8 copper hex ball FXX-D S...
- Page 10 10 × 15 直軸固定座 ball bearing 10 × 12 × 0.1 spacer × 1 墊片 joint ring solid axle nut 10 × 15 ball bearing × 2 10 × 12 × 0.3 培林 Solid axle plate × 2 spacer 滾差直軸連接耦 FXX-D S...
- Page 11 Attaching rear driven shaft set STEP 1 安裝雙節後軸組 5 × 10 ball bearing 8 × 14 ball bearing M2 × 6 Rear gear box cover × 1 Rear gear box mount × 1 rear gear box mount 後齒箱蓋 後齒箱座 bevel gear 17T FXX-D S...
-
Page 14: Front Axle
培林 4.8 × 4.5 copper ball connector × 2 銅製球頭螺絲 M2 × 4 screw × 2 圓頭螺絲 2 × 9.8 pin × 2 插銷 M2.5 × 6 screw × 2 圓頭螺絲 M3 × 11 screw × 4 十字扁頭螺絲 FXX-D S... - Page 17 Pull down piston rod 4mm, attach oil seal and absorb oil overflow with tissue paper. shock spring 將軸心下拉 後，蓋上氣室並以面紙拭去溢出的矽油。 damper retainer Front Silver 前面裝配銀色 Rear 後面裝配紅色 Rod guide × 4 M3 × 5 screw × 4 避震器下蓋墊片 沉頭螺絲 FXX-D S...
- Page 18 插銷 M3 × 8 screw × 4 圓頭螺絲 body mount M3 × 8 screw × 5 clip × 2 沉頭螺絲 形扣 Bumper mount OPTIONAL PARTS FRONT M3 × 8 210361 Carbon bumper support 2.5 M3 × 8 碳纖維泡棉壓板 FXX-D S...
- Page 19 M3 × 6 screw × 1 M3 × 25 圓頭螺絲 M3 × 8 screw × 4 圓頭螺絲 4.8 adjuster M3 × 12 screw × 1 圓頭螺絲 M3 × 8 screw × 2 沉頭螺絲 12.5mm M3 × 25 screw × 1 止付螺絲 FXX-D S...
- Page 20 Notice the latch is in open position “ ” for openning. 注意門栓位置是否位於”開”的狀態才可開。 Recommended hard battery measurement ※ ※ Please set reciever according to L140 × W48 × H26mm. (not exceed) its requirements. 建議使用硬殼鋰電池，規格不超過 長 寬 高 。 詳細設定會依各廠牌不同 FXX-D S...
- Page 21 210379 Rear bumper 後防撞板 REAR Please consider the environment ※ and power for tire choice. ※ 後輪裝配紅點 輪胎的選擇，會因場地、動力而有所不同。 More details, please refer to MST website. 210282 更多詳細內容，請上官網。 MST diffuser R Tire M4 flange nut [ www.rc-mst.com ] 後擾流板 FXX-D S...
-
Page 23: Gear Ratio
FXX-D S GEAR RATIO 10 DRIFT CHASSIS Pinion Gear Reduction Gear Reduction Gear Reduction Gear 馬達齒 次減速齒 次減速齒 次減速齒 Gear C 36T Gear A Gear C Big Bevel Gear PASSIVE GEAR 被動齒 齒輪 齒輪 大傘齒 齒輪 ACTIVE GEAR Pinion Gear...
Need help?
Do you have a question about the FXX-D S and is the answer not in the manual?
Questions and answers