HIKOKI G 1813DF Handling Instructions Manual
  1. Manuals
  2. Brands
  3. HIKOKI Manuals
  4. Power Tool
  5. G 1813DF
  6. Handling instructions manual

HIKOKI G 1813DF Handling Instructions Manual

Hide thumbs Also See for G 1813DF:
Table of Contents

Advertisement

Quick Links

Download this manual
G 1813DF
Handling instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G 1813DF and is the answer not in the manual?

Questions and answers

Related Manuals for HIKOKI G 1813DF

Summary of Contents for HIKOKI G 1813DF

  • Page 1 G 1813DF Handling instructions...
  • Page 4 15°–30°...

  • Page 7: General Power Tool Safety Warnings

    c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi...
  • Page 8 h) Keep handles and grasping surfaces dry, clean b) Operations such as sanding, wire brushing, and free from oil and grease. polishing or hole cutting are not recommended to Slippery handles and grasping surfaces do not be performed with this power tool. allow for safe handling and control of the tool in Operations for which the power tool was not designed unexpected situations.

  • Page 9: Kickback And Related Warnings

    m) Never lay the power tool down until the accessory SAFETY WARNINGS SPECIFIC FOR has come to a complete stop. GRINDING AND ABRASIVE CUTTING- The spinning accessory may grab the surface and pull the power tool out of your control. OFF OPERATIONS n) Do not run the power tool while carrying it at your side.

  • Page 10: Additional Safety Warnings

    – When using dual-purpose (combined grinding and switch. Request an inspection and repair from the dealer cut-off wheels), use only the type A wheel guard. (See where you purchased the unit or a HiKOKI Authorized page 18) Service Center. –...

  • Page 11: Caution On Lithium-Ion Battery

    10. When working at elevated locations, clear the area of Furthermore, please heed the following warning and caution. other people and aware of conditions below you. WARNING 11. Always charge the battery at a temperature of 0°C–40°C. In order to prevent any battery leakage, heat generation, A temperature of less than 0°C will result in over charging smoke emission, explosion and ignition beforehand, please which is dangerous.

  • Page 12: Regarding Lithium-Ion Battery Transportation

    REGARDING LITHIUM-ION BATTERY Housing Bump of lever TRANSPORTATION Switch panel Wheel washer (C) When transporting a lithium-ion battery, please observe the Filter Wheel nut following precautions. WARNING Battery Wrench Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output Abrasive cutting and follow the instructions of the transportation company Auto mode switch...

  • Page 13: Standard Accessories

    The specifi cations of this machine are listed in the Table on Warning page 17. NOTE Due to HiKOKI’s continuing program of research and Remaining battery indicator switch development, the specifi cations herein are subject to change without prior notice.
  • Page 14 ○ Do not block the air vent. Otherwise the interior will overheat, reducing the charger’s performance. ○ If the cooling fan is not operating, contact a HiKOKI Authorized Service Center for repairs. (2) Regarding the temperatures and charging time of the...

  • Page 15: Mounting And Operation

    Table 2 CAUTION ○ If the battery is charged while it is heated because Model UC18YSL3 it has been left for a long time in a location subject to direct sunlight or because the battery has just been Type of battery Li-ion used, the charge indicator lamp of the charger lights Charging voltage...

  • Page 16: Maintenance And Inspection

    MAINTENANCE AND INSPECTION country must be observed. WARNING Be sure to turned off the switch and remove the battery Important notice on the batteries for the HiKOKI before maintenance and inspection. cordless power tools 1. Inspecting the depressed center wheel...
  • Page 17 G1813DF 8000 /min A: 5500 /min 125 mm 22.23 mm 6 mm 80 m/s 3.0 kg (BSL1850MA) 3.4 kg (BSL36B18)
  • Page 18 Type A Type B Type E Type F Type B Type A Type A Type F Type E...
  • Page 19 G1813DF (NN) – BSL1850MA – UC18YSL3 – –...
  • Page 20 125 mm: 375904 125 mm: 372701 336865 371677 339579 377085 377087 938332Z 377086 379591 BSL18.. 329897 UC18YSL3 (14.4 V–18 V) 379422 337108...
  • Page 24 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99747311 G Printed in China...

Table of Contents