Lance-Larkin Brew Express BE-112 Installation Manual
In-the-wall coffee system
Hide thumbs
Also See for Brew Express BE-112:
- Operation manual (11 pages) ,
- Supplementary manual (1 page) ,
- Operation manual (12 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lance-Larkin Brew Express BE-112
Summary of Contents for Lance-Larkin Brew Express BE-112
- Page 1 XPRESS ™ INSTALLAT ION GUIDE BE-112 model no. For more information see our instructional video online at wwww.BrewExpress.com.
-
Page 2: Table Of Contents
CONT EN TS 1. Safety 2. Getting Started 3. Hardware/Tools 4. Specification and Requirements 5. Location (area of Installation) 6. Water Installation 7. Power Installation 8. Brewer Installation 9. Testing 10. Troubleshooting 1 - 2 9 - 12... -
Page 3: Safety
SAfETy IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all Instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. The voltage and frequency of the supply connections should conform to those of the rating label. 4. -
Page 4: Getting Started
GET TING STArTED IMPORTANT: Read and follow instructions carefully before installing your BREW EXPRESS™ in-the-wall COFFEE SYSTEM. For best results its advised that you hire a qualified professional. Getting Started Carefully unpack BREW EXPRESS™ from gift box. Remove hardware kit from foam packaging. Remove carafe from brewing unit and set aside. Remove mounting screws using a Phillips screwdriver (note - if screws are not present look in hardware kit). Separate brewer from Rough-In-Box by holding the Rough-In-Box with one hand, and pulling the brewer with the other hand (see figure below). -
Page 5: Specification And Requirements
SpECIfICATIONS AND rEqUIrEmENTS IMPORTANT: Read and follow instructions carefully before installing your BREW EXPRESS™ in-the-wall COFFEE SYSTEM. For best results it is advised that you hire a qualified professional. 1. Overall Dimensions (Finished Unit with Rough-in-Box) approximately 12.5” x 12.5” (see below). 2. Dimensions for Rough-in-Box (Mounting Structure) approximately 11.5” x 11.5” x 4”. 3. Electrical Requirements 120VAC, 60HZ. (1400 watts). 4. Water Requirements 1/4” OD water supply line (copper or poly) minimum 30 psi to a maximum of 90 psi. -
Page 6: Water Installation
wATEr INSTALLATION Always turn off water supply at source. It is strongly advised you consult a qualified professional plumber when attempting to install BREW EXPRESS™ in-the-wall COFFEE SYSTEM. It is important to make sure there are no conflicts or obstructions in the wall cavity such as plumbing or electrical wires. If in doubt Contact a qualified professional. DO NOT ATTEMPT INSTALLATION. IMPORTANT: It is required that a water filter and shut off valve be installed at source under sink or refrigerator area A. EXISTING HOME Determine closest location on wall where BREW EXPRESS™ is to be installed where water can be plumbed by teeing off water line from sink, refrigerator, ice maker or by simply using the alternate water jug (not supplied). -
Page 7: Brewer Installation
BrEwEr INSTALLATION IMPORTANT: If installing Unit PRIOR to cabinets, it is strongly advised to consult with cabinet maker and build- ing contractor for exact height of counter top due to the various thicknesses of counter tops (tile laminate, granite, etc). For best results cut hole and install unit AFTER cabinets are installed. A. Installing BREW EXPRESS™ on Counter It is best to install the unit so the bottom edge is just off the counter top. In an existing home, this may require part of the back splash to be removed. Use template provided to determine the location to be cut out for rough-in-box. - Page 8 Figure 6 Installation of Brewer Quick connector is valved at rough-in-box so water can be turned on prior to connection to coffee maker. Place unit on a towel or cardboard to protect counter surface. Place BREW EXPRESS™ directly in front of rough-in box. Use quick connector to connect water supply line from BREW EXPRESS™...
-
Page 9: Testing
TESTING Testing Once BREW EXPRESS™ has been installed into the rough-in-box it must be tested to ensure proper operation. Turn on electrical power. Check to see if display panel is illuminated, The display panel is lit when electrical supply has been properly connected. If the display panel is not lit, refer to the troubleshooting section of this manual. Turn on water supply to BREW EXPRESS™. - Page 10 Preheat carafe before brewing coffee especially if used for half pot. (run brew cycle without filter or coffee) • Check volume of water by running a full cycle of water without coffee. If carafe overfills call for technical service. • Check voltage to coffee maker. Water leak from back of brewer • Check quick connect (push connectors together firmly and slightly twist) •...
- Page 11 www.brewexpress.com Printed in CHINA. BE112-IG/02_07 R-1 © LANCE LARKIN 2005...
Need help?
Do you have a question about the Brew Express BE-112 and is the answer not in the manual?
Questions and answers