Table of Contents
Advertisement
en Installation instructions
¡ The appliance fulfils the requirements of protection
class I and must only be connected to an earthed
mains socket.
¡ The H05 V V-F 3G mains connection cable must be
at least 1.5 mm². The yellow-green conductor must
be connected first and be slightly longer than the
two other wires on the appliance side.
¡ In accordance with safety regulations, an all-pole
separator with at least a 3 mm contact opening
must be provided. A separator is not required dur-
ing connection, which is carried out via an earthed
power socket that is easily accessible at all times.
¡ Contact protection must be guaranteed during in-
stallation.
¡ Determine the phase conductor and neutral con-
ductor (zero conductor) in the socket. An incorrect
connection may damage the appliance.
¡ Connect the oven in accordance with the specifica-
tions on the rating plate.
¡ Place the appliance in front of the surround unit to
connect it. The connection cable must be long
enough. Caution: During the installation, ensure that
the power cord is not jammed and does not come
into contact with hot appliance parts.
¡ All work on the appliance, including replacing the
cabling, must only be carried out by the after-sales
service.
17.7 Important information about the
electrical connection
Note the following information and ensure that:
WARNING ‒ Risk of electric shock!
There is a risk of electric shock if you touch live com-
ponents.
Hold the mains plug with dry hands only.
▶
Never pull out the mains plug from the socket while
▶
the appliance is in operation.
Pull out the power cable directly at the plug and
▶
never by pulling the power cable as this may be-
come damaged.
¡ Fit the mains plug and socket together.
¡ The mains plug can be accessed at all times.
¡ The cross section of the cable is sufficient.
¡ The mains cable is not kinked, crushed, modified or
severed.
¡ If required, the mains cable must only be replaced
by a qualified electrician. A replacement mains
cable is available from the after-sales service.
¡ Do not use any multiple plugs or multi-connectors
and extension cords.
¡ The earthing system is correctly installed.
¡ If using a residual current device, only use one that
bears the mark
. The presence of this mark is the
only way to be sure that it fulfils all the applicable
regulations.
¡ The mains cable does not come into contact with
heat sources.
34
17.8 Power cable with protective contact
plug
Connect the appliance only to a correctly installed,
earthed socket.
If the plug can no longer be accessed following install-
ation, provide a separator in the phases in the fixed
electrical installation in accordance with the set-up in-
structions.
17.9 Power cable without protective contact
plug
Only allow a licensed professional to connect the appli-
ance.
Provide a separator in the phases in the fixed electrical
installation in accordance with the construction instruc-
tions. Identify the phase conductor and the neutral con-
ductor (zero conductor) in the socket. An incorrect con-
nection may damage the appliance.
Only connect in accordance with the connection dia-
gram. The information about the voltage can be found
on the rating plate. Connect the wires of the mains
power cable according to the colour coding:
Cable colour
Green-yellow
Blue
Brown
17.10 Only Sweden, Finland and Norway
You can also connect the appliance to the protective
contact system with the enclosed plug. The plug must
be accessible following the installation. If the plug can
no longer be accessed following installation, provide a
separator in the phases in the fixed electrical installa-
tion in accordance with the set-up instructions.
17.11 Securing the appliance
¡ Slide the appliance in fully and centre it.
¡ Screw the appliance into place.
The gap between the worktop and the appliance must
not be closed by additional battens.
Do not attach any thermal insulation strips to the side
panels of the surround unit.
To remove:
¡ Disconnect the appliance from the power supply.
¡ Undo the fastening screws.
Cable type
Earthing cable
Neutral conductor (zero)
Phase conductor (external
conductor)
Advertisement
Table of Contents
