Creative MUVO Go - Portable Waterproof Bluetooth Speaker Manual

OVERVIEW

1. Volume + / Next Track Button
2. Volume - / Previous Track Button
3. Play / Pause Button
4. Lanyard Attachment Point
5. Power Button
6. LED Status Indicator
7. Bluetooth ® Button
8. Charging LED Indicator
9. USB-C Port (for charging only)

BLUETOOTH PAIRING

Button	Action	LED Status Indicator
	Enter Bluetooth Pairing Mode	Flashing White
	Bluetooth Paired	Solid White

NOTE:

• Creative MUVO Go will automatically enter Bluetooth pairing mode upon powering on
• The LED status indicator will blink white when it is powered on and not connected to any device or when it is reconnecting to a previously connected device

CONTROLS

Button	Action

BATTERY CHARGING

Action	Charging LED Indicator
Low Battery	Flashing Red
Charging	Solid Red
Fully Charged	LED Off

BATTERY LEVEL INDICATOR

Button	Action
	Battery Level Low (< 30%) Battery Level Medium (30–70%) Battery Level High (> 70%)

WIRELESS STEREO LINK

Creative MUVO Go features Wireless Stereo Link, a technology that offers a wider soundstage experience by wirelessly linking two MUVO Go speakers. Follow the instructions below to set it up:

Button	Action	LED Status Indicator	Voice Prompt
Device A and B:	Power On MUVO Go Speakers	N / A	N / A
Device A and B:	Manually Enter Bluetooth Pairing Mode	Flashing White	N / A
Device A:	Enter Wireless Stereo Link Pairing	Device A: Pulsing White Device B: Solid White	"Searching For Speaker" "Right Speaker Linked"
Device A:	Disconnect From Wireless Stereo Link	N / A	"Speaker Disconnected"

NOTE:
When both devices are wirelessly linked, only Device A's buttons will remain active

ATTACHING A LANYARD

MASTER RESET

Press and hold the Bluetooth button for 5s to perform a Master Reset. Creative MUVO Go will revert to its default state upon completion.

Master Reset is reserved for cases where users encounter issues while the speaker is in use or during situations such as: Bluetooth Pairing failure, random LED blinking, or data reset.

TECHNICAL SPECIFICATIONS

Power Output: 10W RMS x 2
Total System Peak Power: 40W
Frequency Range: 60–20,000 Hz
Signal-to-noise Ratio (SNR): ≥ 75 dB
Input rating: 5V 2A
Lithium-ion Battery Rating: 7.2V, 2600 mAh (18.72 Wh)
Battery: 2600 mAh rechargeable Lithium-ion x 2
Total Playtime: Up to 18 hours of audio playback^
Charging Time: 4.5 hours*
Bluetooth Version: Bluetooth 5.3
Operating Frequency: 2402–2480 MHz
Operating Range: Up to 10m / 33 ft, measured in open space. Walls and structures may affect range of device Supported Bluetooth Profiles:

• A2DP (Advanced Audio Distribution Profile),
• AVRCP (Audio / Video Remote Control Profile)

Supported Codec: SBC
Maximum RF Output Power: 7 dBm
Maximum Operating Temperature: 45°C

^Based on moderate volume level. Actual battery life will vary with use, settings, songs, and environmental conditions
*Charging time may vary depending on conditions such as environmental temperature or presence of dust on charging contact point, which may affect charging speed

REGISTER YOUR PRODUCT:
creative.com/register

TECHNICAL SUPPORT:
creative.com/support

© 2022 Creative Technology Ltd. All rights reserved. Creative, the Creative logo and MUVO are trademarks or registered trademarks of Creative Technology Ltd in the United States and/or other countries. The Bluetooth ® word mark and logo are owned by Bluetooth SIG, Inc. and any use of such marks by Creative Technology Ltd is under license. All other trademarks are the property of their respective owners and are hereby recognized as such. All specifications are subject to change without notice. Actual product may differ slightly from images shown. Use of this product is subject to a limited warranty.