Universal Remote Control CLIKR-5 UR5L-8700L Operating Instructions

1 4
Operating Instructions For
Introduction Button Functions
The CLIKR TM -5 UR5L-8700L & UR5L-8720L
CLIKR ™ -5
are designed to operate the Scientific-
Atlanta, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
Cable Remote Control
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
CABLE : Cable Converters TV : Televisions
UR5L-8700L & UR5L-8720L
VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
5
Operations
Programming the Remote Control
DEFAULT STATE: There are two ways you can program your CLIKR
Component Default: CABLE Set Top Box (STB)
* The Pre-Programmed 3-Digit Code Method
Channel Default: CABLE channel and numbers * The Auto-Search Method
* The Learning Method
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
through the TV or VCR. Refer to section I for code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
programming steps.
Auto-Search Method scans through all the codes in the remote control, one at a time. The
Volume Default: Volume and Mute control are
Learning Method allows you to transfer functions from other remotes, one button at a time.
automatically transferred to the respective
IMPORTANT SETUP NOTE!
Component mode you select, as follows: CBL:
This pertains to all programming steps. When you are in setup mode, a component LED will light
Cable Set Top Box / TV: TV / AUX: AUX. Volume
for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit
and Mute control for VCR and DVD are auto-
setup mode and you will need to start over.
Universal Remote Control, Inc. matically transferred to the TV. However, you
have the option of controlling CABLE Volume A. Pre-Programmed 3-Digit Code Method
www.universalremote.com
and Mute through the TV, VCR or AUX. Refer to
OCE-0060E REV 07 (02/26/10)
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
section J for programming steps.
STEP2 Press the [COMPONENT] button (TV, Now, repeat the Auto-Search Method for those
VCR, DVD or AUX) to be programmed
Components you could not program earlier
and [OK/SEL] button simultaneously for with the Pre-Programmed Method.If you can't
3 seconds. The Component LED light will
find the right code using the Auto-Search
turn on for 30 seconds indicating the
Method, try the Learning Method in Section C.
unit is ready to be programmed.
C. The Learning Method
STEP3 Point the remote control toward the
Component and enter the 3-digit code
STEP1 Press the [COMPONENT] button
number assigned to your brand.
(TV,VCR,DVD or AUX) to be pro-
*Note : If the 3-digit code number you just grammed and the [ASPECT] buttons
entered is correct, the Component will
simultaneously for 3 seconds until the
turn Off. If it did not turn Off, continue
Component LED light turns on.
entering code numbers listed for that
STEP2 Line up the CLIKR
brand until the Component turns Off.
head-to-head, 1 or 2 inches apart.
STEP4 After you've entered the correct code
STEP3 Press any button on the CLIKR
number and the Component has turned
you want to teach a command to. For
Off, press the [POWER] button to turn the
example, if you want to teach the
Component back On. Now it is time to
[MUTE] button, press the [MUTE] but-
test the VOLUME and MUTE buttons for
ton.
the TV (or PLAY and STOP buttons for
VCR and DVD) to make sure they all work.
STEP4 Press and hold the [MUTE] button on
If any of the functions do not work as they
the other remote until the CLIKR
should, repeat from STEP 3 using the next
Component LED light blinks twice.
3-digit code number listed for that brand
until you find the best Component code.
*Note : The LED will blink 5 times if there
was an error in the learning
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same process. In so, repeat STEPS 3 and
4. Continue learning other buttons
[COMPONENT] button one more time.
The Component LED light will blink by repeating STEPS 3 and 4.
twice to confirm that the code was
STEP5 Once you have completed teaching
successfully stored.
CLIKR TM
Now, program the rest of your Components
Component, save the learned commands
by repeating STEPS 1-5.
by pressing the [COMPONENT] and
*Note : If the Pre-Programmed Method did not [ASPECT] buttons simultaneously until
work, or if the Code Tables do not list the Component LED blinks 3 times. Now
your Component brand, use the Auto- test all the buttons to make sure they
Search Method as explained in Section B. learned correctly.
D. Erasing a Single Learned Command
B. Auto-Search Method
STEP1 Press the [COMPONENT] and [ASPECT]
STEP1 Turn on the Component you want to
buttons simultaneously for 3 seconds
program (TV, VCR, DVD or AUX).
until the Component LED light turns on.
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed STEP2 Press and hold the button you want to
erase for 3 seconds. The Component LED
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light will blink twice to confirm the erasure.
TM -5 remote:
will turn on for 30 seconds indicating
STEP3 To exit, press and hold both the [COM-
the unit is ready to be programmed.
PONENT] and [ASPECT] buttons simul-
STEP3 Point the remote toward the Component taneously until the Component LED
blinks 3 times.
and press the [CH ] or [CH ] button one
step at a time or keep it pressed. The
E. Erasing All Learned Commands
remote will emit a series of ON/OFF com-
mands. Release the [CH ] or [CH ] but- from One Component
ton as soon as the Component turns Off.
STEP1 Press the [COMPONENT] and [ASPECT]
STEP4 Test functions. (Same as for 3-Digit Code
buttons simultaneously for 3 seconds
Programming Method - Section A). If any
until the Component LED light turns on.
of the functions do not work as they
STEP2 Press and hold both the [COMPONENT]
should, repeat from STEP 3 using [CH ]
button you want to erase and the
or [CH ] buttons to find the correct code.
[PAUSE] button for 5 seconds. The
STEP5 Save the code. (Same as for 3-Digit Code
Component LED will blink twice to con-
Programming Method - Section A).
firm the erasure.
STEP3 To exit, press and hold both the [COMPONENT] H. Programming the System On/Off Button
and [ASPECT] buttons simultaneously until the
This allows you to program the System On/Off
Component LED blinks 3 times.
button so it can send up to five power On/Off
F. Finding a Component Button's
commands with one button press.
Setup Code Number
STEP1 Press the [CBL] button.
If you used either the Auto-Search or Learning
STEP2 Press the [SYSTEM ON/OFF] button and
Methods to program a Component, you may not
know what the correct code number is. Here is a the [OK/SEL] button simultaneously for 3
way for you to identify the code number, so you seconds. The [CBL] button will turn on for
30 seconds.
can record it for future reference.
STEP1 Press the [COMPONENT] button (TV, STEP3 Press the first [COMPONENT] button you want
VCR, DVD or AUX) you want to verify and to store in the [SYSTEM ON/OFF] button and
TM -5 to the other remote,
the [OK/SEL] button simultaneously for 3 then the [POWER] button. Repeat this for other
seconds. The Component LED light will
Components until you have stored all the
turn on for 30 seconds.
desired power commands into the [SYSTEM
TM -5 that
ON/OFF] button.
STEP2 Press the [INFO] button and count the num-
ber of times the Component LED light blinks.
STEP4 Press the [CH ] button to save the
This number indicates the first digit of the
power commands you stored. The [CBL]
code, followed by the second and third,
button will blink twice to confirm the
each separated by a one second pause
commands have been saved.
when the LED will turn off.
TM -5
I. Programming Channel Control
*Note : 10 blinks represents the number zero.
You can program the channel controls (Channel
Example : One blink, (pause), eight blinks,
(pause) and three blinks, indicates Up, Channel Down, Last and Numbers) from one
code number 183. Component to operate in another Component
mode. Default channel control settings on the
G. AUX Function: Programming a 5 th
remote control are as follows:
Component
CBL : CBL T V : CBL
You can take advantage of the AUX function to
DVD : DVD AUX : AUX
-5 all desired commands for that program a 5 th Component such as a second TV,
VCR, DVD or Audio Component.
If you wish to store the TV channel control in TV
mode, use the following steps.
STEP1 Turn on the 5 th Component you want to
program (TV, VCR, DVD or Audio).
STEP1 Press the [TV] button and the [OK/SEL]
STEP2 Press the [AUX] button and the button simultaneously for 3 seconds.
The [TV] Component LED will turn on for
[OK/SEL] button simultaneously for 3
30 seconds.
seconds.The [AUX] Component LED will
turn on for 30 seconds.
STEP2 Press the [VOL ] button.
STEP3 Press the [COMPONENT] button you
STEP3 Press the [TV] button again.
want to setup. Point the remote control
The Component LED will blink twice to
toward the Component and enter the 3-
confirm the programming.
digit code number assigned to your
brand.
To return to original state:
*Note : If the 3-digit code number you just
If you wish to restore the CABLE channel con-
entered is the correct number, the
trol in TV mode, repeat the above steps but
Component will turn Off. If it did not
press [CBL] in STEP3 .
turn Off, continue entering code num-
bers listed for that brand until the
J. Programming Volume Control
Component turns Off.
Volume and Mute control are factory-programmed to
STEP4 Test functions. (Same as for 3-Digit Code
automatically transfer to the respective Component
Programming Method - Section A). If any
mode you select, as follows:
of the functions do not work as they should,
you need to find a new code. CBL : CBL T V : TV
DVD : TV AUX : AUX
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
However, you can program the volume controls
one more time. The Component LED light
(Volume Up, Volume Down and Mute) from one
will blink twice to confirm the code was
Component to operate in another Component.
stored. Now when you press the AUX
button, all the buttons will work with that If you wish to store the TV volume control in CBL
5 th Component. mode, use the following steps.
6
STEP1 Press the [CBL] button and the [OK/SEL] but-
Set-up Code Tables
ton simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
CBL-CABLE Converters
STEP2 Press the [VOL ] button.
Manufacturer/Brand Set-Up Code Number
STEP3 Press the [TV] button.
SCIENTIFIC ATLANTA 001 003 041 042 045 046
The Component LED will blink twice to
PIONEER 001 103 034 051 063 076 105
confirm the programming. PACE 001 005 002
SAMSUNG 001 030
To return to original state:
MOTOROLA 002 111 148
If you wish to restore the CBL volume control in CBL
DIGEO 153
GENERAL INSTRUMENT 005 103 104
mode, repeat the above steps but press [CBL] in STEP3 .
HAMLIN 049 050 055
K. Programming a 'Macro' button. HITACHI 103 055
JERROLD 005 004 103 005 003 008 009 010 069
If your remote model has custom-programmable Macro
MAGNAVOX 010 012
buttons available, they can be programmed to act as a
MEMOREX 052
'Macro' or Favorite Channel button in CABLE mode. This
MOXI 111 252 153
allows you to program up to five 2-digit channels, four 3- NFUSION 192
digit channels or three 4-digit channels that can be PANASONIC 044 047
PHILIPS 006 012 013 020 085
accessed with one button press.
PULSAR 052
STEP1 Press the [CBL] button to select the CBL mode.
RCA 047
REGAL 049 050
STEP2 Press the [MACRO] button and [OK/SEL]
REGENCY 057
button simultaneously for 3 seconds. The
SKY 230 204
[CBL] button will turn on for 30 seconds.
SONY 108
SPRUCER 047
STEP3 Enter the the 2, 3 or 4-digit code for the channel
TELNET 354
you want programmed first (for example, 007)
TOCOM 039 040 056
using the Number Pad, then press the [STOP]
TOSHIBA 052
button. Then enter the code for the next chan-
VIEWSTAR 012 015
nel (for example, 050), then press the [STOP]
ZENITH 052 060 093 100
button. Repeat this process for the third chan-
VCR : CBL
TV
nel. The [CBL] button will blink once for each
channel entered.
Manufacturer/Brand Set-Up Code Number
STEP4 Press the [CH ] button to store the channels
A MARK 112 143
that were selected. The [CBL] button will blink ABEX 025
twice to confirm the storage of commands. ACCURIAN 036
ADMIRAL 072 251 333
To access the programmed channels, press the
ADVENT 247 388
[MACRO] button once. This will bring up the ADVENTURA 002
AIKO 103
first channel. Press once again and it will bring
AKAI 116 146 248 404 405 473 475 323 387 391
up the second channel. Press again and it will
ALBATRON 017
bring up the third channel. ALERON 028
AMERICA ACTION 043
L. Low Battery Warning
AMPRO 073
AMSTRAD 052
When the batteries are low and need to be replaced
ANAM 043 054 056 080 112
with fresh batteries, the Component LED lights will AOC 116 363 112 058
blink 2 times in sequence whenever a [POWER] but- APEX 572
ton is pressed to turn on equipment. APEX DIGITAL 006
AQUAVISION 573 574
M. Memory Lock System ASTAR 477
AUDIOVOX 076 454 388
AVENTURA 052
This remote control is designed to retain pro-
AVION 441
grammed memory for 10 years even after batteries
AXION 039
are removed from the remote control.
BELCOR 116
BELL&HOWELL 333 072
N. Record Your Component Set-up Codes
BENQ 423 600
VCR : TV
BOXLIGHT 266
TV Set-up Code Number:
BRADFORD 043
VCR Set-up Code Number: BROCKWOOD 116
BROKSONIC 238
DVD Set-up Code Number:
BYDESIGN 031 032
CANDLE 116 002 003 363
AUX Set-up Code Number:
CAPEHART 058
For additional information about your remote CARY AUDIO DESIGN 266
control, go to www.universalremote.com CELEBRITY 001
TV TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
CENTURION 116 INITIAL 035 282
CETRONIC 043 INSIGNIA 350 400 052 164 403 454 457
CHANGHONG 247 INTEQ 073
CITIZEN 116 002 003 363 043 258 103 143 JANEIL 002
CLARION 043 JBL 164
CLASSIC 043 JCB 001
CLP CLASSIC 333
JCPENNEY 024 116 008 009 030 065 258 143 333 363
COLORTYME 116 JENSEN 013
CONCERTO 363 JVC 038 034 001 083 199 210 533 581
CONCIERGE 073 KAWASHO 116 001
CONTEC 043 050 051 KEC 043
CORNEA 116 KENWOOD 116 001
CORONADO 143
KLEGG 466
CRAIG 043 054 KLOSS 002 059
CROSLEY 164 KMC 143
CROWN 043 143 KNOLL SYSTEMS 230
CURTIS MATHES 116 258 363 143 KONKA 457
CXC 043 KREISEN 530
CYBERHOME 015 KTV 043 116 143 154
DAEWOO 363 016 043 044 076 103 114 125 127 143
KURAZAI 072
DAYTRON 363 143 LG 363 113 116 102 106 112 127 143 569 284
DELL 320 164 363 LITEON 268
DIGITAL PROJECTION 570 LODGENET 072
DIMENSIA 333 LOEWE 164
DREAMVISION 235 LOGIK 072
DUKANE 011 025
LUXMAN 363
DUMONT 116 073 LXI 166 007 138 052 251 333 164
DURABRAND 096 052 MAGNAVOX 164 059 116 003 060 061 363 127 022 333
DWIN 257 094 226 390 467 431
DYNASTY 043 MAJESTIC 333 072
DYNEX 400 MARANTZ 116 164 281 562 584
EIKI 187 MATSUI 164
ELECTROBAND 001 MATSUSHITA 080
MAXENT 242
ELECTROGRAPH 466
ELECTROHOME 143 024 076 196 MEGATRON 116 011
ELEKTRA 072 MEMOREX 007 072 363
ELEMENT 363 494 526 MGA 116 363 024 028 042
EMERSON 028 048 043 155 005 116 363 047 050 051 MIDLAND 333 073
076 096 143 153 154 052 514 MINTEK 362
ENVISION 116 MINUTZ 008
EPSON 324 590
MISAKAI 052
ESA 323
MITSUBISHI 124 109 024 028 040 042 146 363 348 450
FISHER 007 057 MONIVISION 017
FUJITSU 246 198 410 MONTGOMERY WARD 333 072
FUNAI 028 043 052 MOTOROLA 081
FUTURETECH 043 MTC 116 363 258
GATEWAY 242 268 MULTITECH 043
GE 073 116 008 009 034 056 074 155 333 363
NAD 138 025
GEM 391 NEC 272 197134 116 040 016 024 056 019 262 236
GIBRALTER 116 073 281 575
GO VIDEO 026 NET TV 242
GOLDSTAR 113 116 102 363 106 112 127 143 NIKEI 043
GRUNPY 028 043 NIKKO 116
HAIER 363 501 NIKO 527
HALL MARK 363 NORCENT 390
HANNSPREE 349 381 NORWOOD MICRO 027
HARLEY DAVIDSON 028 NTC 103
HARVARD 043 NUVISION 351 567
HAVERMY 081 OLEVIA 432 363 333
HELLO KITTY 076 ONKING 043
HIMITSU 043 ONWA 043
OPTIMUS 025
HISENSE 419 442
HITACHI 011 166 009 010 012 023 075 143 158 072 OPTOMA 265 249
363 250 587
OPTONICA 019 251
HP 378 316 327 421 ORION 096
HUMAX 518 PANASONIC 080 034 056 164 208 359 552 524
HYUNDAI 337 338 PHILCO 116 003 059 060 164 363 024 056
ILO 472 399 PHILIPS 164 005 093 038 116 003 363 059 127 206
INFINITY 164 431 333 161 594
INFOCUS 333 230 547 548 470 532 564 595 PILOT 116