Universal Remote Control CLIKR-5 UR5U-8700L Operating Instructions

1 4
Operating Instructions For
Introduction Button Functions
The CLIKR TM -5 UR5U-8700L & UR5U-8720L
CLIKR ™ -5
are designed to operate the Scientific-
Atlanta, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
Cable Remote Control
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
CABLE : Cable Converters TV : Televisions
UR5U-8700L & UR5U-8720L
VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
Operations
5
Programming the Remote Control
DEFAULT STATE:
There are two ways you can program your CLIKR
Component Default: CABLE Set Top Box (STB)
* The Pre-Programmed 3-Digit Code Method
Channel Default: CABLE channel and numbers
* The Auto-Search Method
through the CABLE STB. You have the option of
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
controlling your CABLE channel and numbers
code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
through the TV or VCR. Refer to section F for
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
programming steps.
Auto-Search Method scans through all the codes in the remote control, one at a time.
Volume Default: Volume and Mute control are
automatically transferred to the respective
IMPORTANT SETUP NOTE!
Component mode you select, as follows: CBL:
This pertains to all programming steps. When you are in setup mode, a component LED will
Cable Set Top Box / TV: TV / AUX: AUX. Volume
light for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off
and Mute control for VCR and DVD are
and exit setup mode and you will need to start over.
Universal Remote Control, Inc. automatically transferred to the TV. However,
A. Pre-Programmed 3-Digit Code Method
you have the option of controlling CABLE
www.universalremote.com
Volume and Mute through the TV, VCR or AUX.
OCE-0060C REV 07 (02/26/10) STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
Refer to section G for programming steps.
STEP2 Press the [COMPONENT] button (TV, STEP4 Test functions. (Same as for 3-Digit
VCR, DVD or AUX) to be programmed Code Programming Method - Section
and [OK/SEL] button simultaneously for A). If any of the functions do not work as
3 seconds. The Component LED light they should, repeat from STEP 3 using
will turn on for 30 seconds indicating [CH ] or [CH ] buttons to find the
the unit is ready to be programmed.
correct code.
STEP3 Point the remote control toward the
STEP5 Save the code. (Same as for 3-Digit
Component and enter the 3-digit code
Code Programming Method - Section A).
number assigned to your brand.
Now, repeat the Auto-Search Method for
*Note : If the 3-digit code number you just
those Components you could not program
entered is correct, the Component will
earlier with the Pre-Programmed Method.
turn Off. If it did not turn Off, continue
entering code numbers listed for that
C. Finding a Component Button' s Setup
brand until the Component turns Off.
Code Number
STEP4 After you've entered the correct code
If you used the Auto-Search Method to
number and the Component has turned
Off, press the [POWER] button to turn program a Component, you may not know
the Component back On. Now it is time
what the correct code number is. Here is a
to test the VOLUME and MUTE buttons
way for you to identify the code number, so
for the TV (or PLAY and STOP buttons
you can record it for future reference.
for VCR and DVD) to make sure they all
work. If any of the functions do not
Press the [COMPONENT] button (TV,
STEP1
work as they should, repeat from STEP
VCR, DVD or AUX) you want to verify
3 using the next 3-digit code number
and the [OK/SEL] button simultaneously
listed for that brand until you find the
for 3 seconds. The Component LED light
best Component code.
will turn on for 30 seconds.
STEP5 Once you have found the correct 3-digit
Press the [INFO] button and count the
STEP2
code, save it by pressing the same
number of times the Component LED
[COMPONENT] button one more time.
light blinks. This number indicates
The Component LED light will blink
the first digit of the code, followed by
twice to confirm that the code was
the second and third, each separated
successfully stored.
by a one second pause when the LED
will turn off.
Now, program the rest of your Components by
repeating STEPS 1-5.
*Note : 10 blinks represents the number zero.
*Note : If the Pre-Programmed Method did not
Example : One blink, (pause), eight blinks,
work, or if the Code Tables do not list
(pause) and three blinks, indicates
your Component brand, use the Auto-
code number 183.
Search Method as explained in Section B.
D. AUX Function: Programming a 5
B. Auto-Search Method
Component
STEP1 Turn on the Component you want to
TM -5 remote: You can take advantage of the AUX function to
program (TV, VCR, DVD or AUX).
program a 5 th
STEP2 Press the [COMPONENT] button (TV, TV, VCR, DVD or Audio Component.
VCR, DVD or AUX) to be programmed
STEP1 Turn on the 5
and [OK/SEL] button simultaneously for
to program (TV, VCR, DVD or Audio).
3 seconds. The Component LED light
will turn on for 30 seconds indicating STEP2 Press the [AUX] button and the
the unit is ready to be programmed. [OK/SEL] button simultaneously for 3
seconds.The [AUX] Component LED
STEP3 Point the remote toward the Component
will turn on for 30 seconds.
and press the [CH ] or [CH ] button
one step at a time or keep it pressed. STEP3 Press the [COMPONENT] button you
The remote will emit a series of ON/OFF want to setup. Point the remote control
commands. Release the [CH ] or toward the Component and enter the 3-
[CH ] button as soon as the Component
digit code number assigned to your
turns Off.
brand.
*Note : If the 3-digit code number you just
STEP1 Press the [TV] button and the
entered is the correct number, the
[OK/SEL] button simultaneously for 3
Component will turn Off. If it did
seconds. The [TV] Component LED
not turn Off, continue entering
will turn on for 30 seconds.
code numbers listed for that brand
until the Component turns Off.
STEP2 Press the [VOL ] button.
STEP4 Test functions. (Same as for 3-Digit STEP3 Press the [TV] button again.
Code Programming Method - Section
The Component LED will blink twice
A). If any of the functions do not work
to confirm the programming.
as they should, you need to find a
new code. To return to original state:
STEP5 Once you have found the correct 3-
If you wish to restore the CABLE channel
digit code, save it by pressing the
control in TV mode, repeat the above steps but
[AUX] button one more time. The
press [CBL] in STEP3 .
Component LED light will blink twice
to confirm the code was stored. Now
G. Programming Volume Control
when you press the AUX button, all
the buttons will work with that 5 th
Volume and Mute control are factory-
Component.
programmed to automatically transfer to the
respective Component mode you select, as
E. Programming the System On/Off Button
follows:
This allows you to program the System On/Off
button so it can send up to five power On/Off CBL : CBL T V : TV
commands with one button press.
DVD: TV AUX: AUX
Press the [CBL] button.
STEP1
However, you can program the volume controls
STEP2 Press the [SYSTEM ON/OFF] button (Volume Up, Volume Down and Mute) from one
and the [OK/SEL] button simultaneously
Component to operate in another Component.
for 3 seconds. The [CBL] button will turn
on for 30 seconds. If you wish to store the TV volume control in
CBL mode, use the following steps.
Press the first [COMPONENT] button
STEP3
you want to store in the [SYSTEM
STEP1 Press the [CBL] button and the
ON/OFF] button and then the
[OK/SEL] button simultaneously for 3
[POWER] button. Repeat this for
seconds. The [CBL] Component LED
other Components until you have
will turn on for 30 seconds.
stored all the desired power
commands into the [SYSTEM
STEP2 Press the [VOL ] button.
ON/OFF] button.
STEP3 Press the [TV] button.
STEP4 Press the [CH ] button to save the
th
The Component LED will blink twice
power commands you stored. The
to confirm the programming.
[CBL] button will blink twice to
confirm the commands have been
To return to original state:
saved.
Component such as a second
If you wish to restore the CBL volume control
F. Programming Channel Control in CBL mode, repeat the above steps but press
th Component you want
[CBL] in STEP3 .
You can program the channel controls
(Channel Up, Channel Down, Last and
H. Programming a 'Macro' button.
Numbers) from one Component to operate in
another Component mode. Default channel
If your remote model has custom-programmable
control settings on the remote control are as
Macro buttons available, they can be
follows:
programmed to act as a 'Macro' or Favorite
CBL : CBL T V : CBL VCR: CBL
Channel button in CABLE mode. This allows you
DVD: DVD AUX: AUX
to program up to five 2-digit channels, four 3-digit
channels or three 4-digit channels that can be
If you wish to store the TV channel control in
TV mode, use the following steps. accessed with one button press.
6
STEP1 Press the [CBL] button to select the CBL
Set-up Code Tables
mode.
CBL-CABLE Converters
STEP2 Press the [MACRO] button and [OK/SEL]
Manufacturer/Brand Set-Up Code Number
button simultaneously for 3 seconds.
SCIENTIFIC ATLANTA 001 003 041 042 045 046
The [CBL] button will turn on for 30
PIONEER 001 103 034 051 063 076 105
seconds.
PACE 001 005 002
SAMSUNG 001 030
STEP3 Enter the the 2, 3 or 4-digit code for the
MOTOROLA 002 111 148
channel you want programmed first (for DIGEO 153
GENERAL INSTRUMENT 005 103 104
example, 007) using the Number Pad,
HAMLIN 049 050 055
then press the [STOP] button. Then HITACHI 103 055
JERROLD 005 004 103 005 003 008 009 010 069
enter the code for the next channel (for
MAGNAVOX 010 012
example, 050), then press the [STOP]
MEMOREX 052
button. Repeat this process for the third MOXI 111 252 153
NFUSION 192
channel. The [CBL] button will blink
PANASONIC 044 047
once for each channel entered. PHILIPS 006 012 013 020 085
PULSAR 052
STEP4 Press the [CH ] button to store the RCA 047
REGAL 049 050
channels that were selected. The [CBL]
REGENCY 057
button will blink twice to confirm the
SKY 230 204
storage of commands. SONY 108
SPRUCER 047
TELNET 354
To access the programmed channels, press
VCR: TV
TOCOM 039 040 056
the [MACRO] button once. This will bring up
TOSHIBA 052
the first channel. Press once again and it will VIEWSTAR 012 015
ZENITH 052 060 093 100
bring up the second channel. Press again and
it will bring up the third channel.
TV
Manufacturer/Brand Set-Up Code Number
I. Low Battery Warning
A MARK 112 143
ABEX 025
When the batteries are low and need to be
ACCURIAN 036
ADMIRAL 072 251 333
replaced with fresh batteries, the Component
ADVENT 247 388
LED lights will blink 2 times in sequence
ADVENTURA 002
whenever a [POWER] button is pressed to turn AIKO 103
AKAI 116 146 248 404 405 473 475 323 387 391
on equipment.
ALBATRON 017
ALERON 028
J. Memory Lock System AMERICA ACTION 043
AMPRO 073
AMSTRAD 052
This remote control is designed to retain
ANAM 043 054 056 080 112
programmed memory for 10 years even after
AOC 116 363 112 058
batteries are removed from the remote control. APEX 572
APEX DIGITAL 006
AQUAVISION 573 574
K. Record Your Component Set-up Codes
ASTAR 477
AUDIOVOX 076 454 388
TV Set-up Code Number: AVENTURA 052
AVION 441
VCR Set-up Code Number: AXION 039
BELCOR 116
DVD Set-up Code Number: BELL&HOWELL 333 072
BENQ 423 600
AUX Set-up Code Number: BOXLIGHT 266
BRADFORD 043
For additional information about your remote
BROCKWOOD 116
BROKSONIC 238
control, go to www.universalremote.com
BYDESIGN 031 032
CANDLE 116 002 003 363
CAPEHART 058
CARY AUDIO DESIGN 266
CELEBRITY 001
TV TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
CENTURION 116 INITIAL 035 282
CETRONIC 043 INSIGNIA 350 400 052 164 403 454 457
CHANGHONG 247 INTEQ 073
CITIZEN 116 002 003 363 043 258 103 143 JANEIL 002
CLARION 043 JBL 164
CLASSIC 043 JCB 001
CLP CLASSIC 333
JCPENNEY 024 116 008 009 030 065 258 143 333 363
COLORTYME 116 JENSEN 013
CONCERTO 363 JVC 038 034 001 083 199 210 533 581
CONCIERGE 073 KAWASHO 116 001
CONTEC 043 050 051 KEC 043
CORNEA 116 KENWOOD 116 001
CORONADO 143
KLEGG 466
CRAIG 043 054 KLOSS 002 059
CROSLEY 164 KMC 143
CROWN 043 143 KNOLL SYSTEMS 230
CURTIS MATHES 116 258 363 143 KONKA 457
CXC 043 KREISEN 530
CYBERHOME 015 KTV 043 116 143 154
DAEWOO 363 016 043 044 076 103 114 125 127 143
KURAZAI 072
DAYTRON 363 143 LG 363 113 116 102 106 112 127 143 569 284
DELL 320 164 363 LITEON 268
DIGITAL PROJECTION 570 LODGENET 072
DIMENSIA 333 LOEWE 164
DREAMVISION 235 LOGIK 072
DUKANE 011 025
LUXMAN 363
DUMONT 116 073 LXI 166 007 138 052 251 333 164
DURABRAND 096 052 MAGNAVOX 164 059 116 003 060 061 363 127 022 333
DWIN 257 094 226 390 467 431
DYNASTY 043 MAJESTIC 333 072
DYNEX 400 MARANTZ 116 164 281 562 584
EIKI 187 MATSUI 164
ELECTROBAND 001 MATSUSHITA 080
MAXENT 242
ELECTROGRAPH 466
ELECTROHOME 143 024 076 196 MEGATRON 116 011
ELEKTRA 072 MEMOREX 007 072 363
ELEMENT 363 494 526 MGA 116 363 024 028 042
EMERSON 028 048 043 155 005 116 363 047 050 051 MIDLAND 333 073
076 096 143 153 154 052 514 MINTEK 362
ENVISION 116 MINUTZ 008
EPSON 324 590
MISAKAI 052
ESA 323
MITSUBISHI 124 109 024 028 040 042 146 363 348 450
FISHER 007 057 MONIVISION 017
FUJITSU 246 198 410 MONTGOMERY WARD 333 072
FUNAI 028 043 052 MOTOROLA 081
FUTURETECH 043 MTC 116 363 258
GATEWAY 242 268 MULTITECH 043
GE 073 116 008 009 034 056 074 155 333 363
NAD 138 025
GEM 391 NEC 272 197134 116 040 016 024 056 019 262 236
GIBRALTER 116 073 281 575
GO VIDEO 026 NET TV 242
GOLDSTAR 113 116 102 363 106 112 127 143 NIKEI 043
GRUNPY 028 043 NIKKO 116
HAIER 363 501 NIKO 527
HALL MARK 363 NORCENT 390
HANNSPREE 349 381 NORWOOD MICRO 027
HARLEY DAVIDSON 028 NTC 103
HARVARD 043 NUVISION 351 567
HAVERMY 081 OLEVIA 432 363 333
HELLO KITTY 076 ONKING 043
HIMITSU 043 ONWA 043
OPTIMUS 025
HISENSE 419 442
HITACHI 011 166 009 010 012 023 075 143 158 072 OPTOMA 265 249
363 250 587
OPTONICA 019 251
HP 378 316 327 421 ORION 096
HUMAX 518 PANASONIC 080 034 056 164 208 359 552 524
HYUNDAI 337 338 PHILCO 116 003 059 060 164 363 024 056
ILO 472 399 PHILIPS 164 005 093 038 116 003 363 059 127 206
INFINITY 164 431 333 161 594
INFOCUS 333 230 547 548 470 532 564 595 PILOT 116