Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Edimax GS-5210PLG
Summary of Contents for Edimax GS-5210PLG
- Page 1 GS-5210PLG User Manual 03-2022 / v1.0...
-
Page 2: Table Of Contents
Contents I. Product Information ..........1 I-1. Package Content ..............2 I-2. Hardware Overview ............. 2 I-3. LED Status................3 II. Installation .............. 3 II-1. Physically Setup ..............3 II-2. Connection ................5 III. Web-based Configuration Utility ......6 Web-based Switch Configuration ..... 8 IV-1. - Page 3 IV-8-3. IEEE 802.1p QoS: ..........19 IV-9. Broadcast Storm Control ............ 20 IV-10. Rate Limiting ..............21 IV-11. Loop Detect/Prevent ............. 22 IV-12. IGMP Snooping ............. 23 IV-13. PoE ................24 IV-14. Password ............... 25 IV-15. Logout ................25 V. Safety Instructions ..........26...
-
Page 4: Product Information
I. Product Information The Edimax Pro GS-5210PLG is a web-smart switch with 8 Gigabit PoE+, 1 Gigabit RJ45 uplink port and 1 Gigabit SFP uplink. Designed for medium to small network environments, its standard 19-inch 1U rack-mount brackets allow for integration with the most widely used mounting systems on the market. -
Page 5: I-1. Package Content
Package Content Before start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s): Quick Installation Power Cord Rack-Mount Kit GS-5210PLG Guide I-2. Hardware Overview Gigabit PoE Port... -
Page 6: I-3. Led Status
I-3. LED Status Function Color Status Description Power on Green Power off Blinking Booting up Total PoE power consumed is OVER PoE power budget PoE Alert Green Total PoE power consumed is under PoE power budget Link at 1000Mbps Green Blinking Sending or receiving data Link/ACT... - Page 7 2. Rack-mount the switch: You can mount the switch in any standard size, 19-inch (about 48 cm) wide rack with 1 Rack Unit (1U) of space, which is 1.75 inches (4.45 cm) high. A pair of extension brackets and screws are needed to adapt the switch to the rack size.
-
Page 8: Ii-2. Connection
II-2. Connection 1. Power on: Connect the power cord to the switch and the power outlet. The switch is powered by the 100-240VAC 50/60Hz external high- performance power supply. (Note: Make sure the PWR LED is green.) 2. Uplink: Plug the standard Cat5e(or above) Ethernet cable into the LAN port no. -
Page 9: Web-Based Configuration Utility
III. Web-based Configuration Utility This section describes how to navigate the web-based switch configuration utility through web browser. Be sure to disable any browser pop-up blocker. Browser Restrictions If you are using older versions of Internet Explorer, you cannot directly use an IPv6 address to access the device. - Page 10 3. The default username is “admin” and the default password is “1234”. The first time that you log in with the default username and password, you are required to change password.
-
Page 11: Web-Based Switch Configuration
This chapter describes how to use the web-based management interface (Web UI) to configure the switch’s features. For the purposes of this manual of GS-5210PLG, the user interface is separated into fifteen sections, as shown in the following figure: IV-1. System This page shows system current information. -
Page 12: Iv-2. Management
Item Description Model Name Model name of the switch. System name of the switch. This name will also use Device Name as CLI prefix of each line. (“Switch>” or “Switch#”). Firmware Current running firmware image version. Version MAC Address Base MAC address of the switch. IPv4 Address Current system IPv4 address. - Page 13 “Reboot” button. Management Reset: You can reset the switch to default by pressing the “Reset “button. Item Description Backup: Backup the configurations from this GS-5210PLG. Configuration Restore/Backup Restore: Restore the configurations choosing configuration file from PC or NB. Item Description Firmware...
-
Page 14: Iv-3. Port
IV-3. Port Configure settings for switch port related features. Item Description Port Port number Port speed capabilities. Auto: Auto speed with all capabilities. 10M Half: Speed with Half-Duplex Speed 10M Full: Speed with Full-Duplex 100M Half: Speed with Half-Duplex 100M Full: Speed with Full-Duplex Down: Displays port is not in use. -
Page 15: Iv-4. Long Range Mode
IV-4. Long Range Mode This page shows port current status. Select Enable or Disable to enable or disable Long Range Mode. NOTE: Enable long range mode will double the cabling distance but reduce the speed to 10Mbps. IV-5. VLAN This page allows user to configure each port of selected VLANs. PVID=Port VLAN ID, Each port only belong to a PVID exclusively. - Page 16 Item Description Apply Click “Apply” to save the values. Port Designated port number. PVID Enter a Port VLAN ID for each port. Click “Create New VLAN” to enter new Create New VLAN VLAN settings. VLAN ID Virtual LAN ID, or called VID Non-Member Port is not a member of a VLAN.
- Page 17 Change the Member State Click” Modify” button to change the member state. There are 3 VLAN member states: Click on the box (Default: ) to change each the member state, and click “Apply”. SimpleClick ”Delete” button to delete the targeted VLAN. Note: If the VLAN ID is used as PVID, deleting the VLAN ID is not allowed.
-
Page 18: Iv-6. Trunking
IV-6. Trunking Link aggregation (trunking) is the grouping of physical ports into one logical higher-capacity link. You may want to trunk ports if, for example, it is cheaper to use multiple lower-speed links than to under-utilize a high-speed, but more costly, single-port link. -
Page 19: Iv-7. Mirror
By default, the Switch uses the MAC SA & DA distribution type. MAC SA & DA: To distribute traffic based on a combination of the packet’s source MAC address and destination MAC address. MAC SA: To distribute traffic based on the packet’s source MAC address. -
Page 20: Iv-8. Qos
Monitor Port Select the mirror destination port. Mirrored Port List Choose the destination of the mirrored port. Apply Click Apply to save the changes. IV-8. QoS There are two options of QoS mechanism are provided for traffic forwarding: port-based QoS and 802.1p QoS. Users can switch to either of them on the Web page. -
Page 21: Iv-8-2. Port-Based Qos
IV-8-2. Port-Based QoS: Queue0 Low Priority Queue1 Normal Priority Queue2 Medium Priority Queue3 High Priority Item Description WFQ(Weighted Fair Queue) Schedule Method Strict Priority WFQ weight options: Weight (WFQ Method ONLY) Apply Click Apply to save the changes. -
Page 22: Iv-8-3. Ieee 802.1P Qos
IV-8-3. IEEE 802.1p QoS: If QoS type is set to 802.1p, the priority is based on the incoming PCP field of the traffic. The current queue for each PCP is configured as below. PCP value Priority Acronym Traffic types 0 (lowest) Background 1(default) Best effort... -
Page 23: Iv-9. Broadcast Storm Control
Item Description Schedule Method WFQ(Weighted Fair Queue) Strict Priority Weight WFQ weight options: (WFQ Method ONLY) Apply Click Apply to save the changes. IV-9. Broadcast Storm Control A traffic storm occurs when packets flood the network ports, creating traffic and impacting network performance in a negative way. The broadcast storm control feature prevents network ports from being disrupted by a broadcast, multicast, or DLF (Destination Lookup Failure) traffic storm. -
Page 24: Iv-10. Rate Limiting
IV-10. Rate Limiting When the Rate Control feature is enabled, GS-5210PLG provides Ingress/Egress traffic Rate Control per port for broadcast traffic type. Enable this feature to reduce broadcast packets in your network. Click on a port number to enter the configuration page as shown below:... -
Page 25: Iv-11. Loop Detect/Prevent
Click the drop down menus to change the Ingress/Egress rate, and click “Apply” to apply the setting. IV-11. Loop Detect/Prevent Users can choose to enable Loop Detection or Loop Prevention. Item Description By Default, Loop Detection/Prevention is disabled. -
Page 26: Iv-12. Igmp Snooping
Loop Detection When loop is detected, the Link/ACT LEDs of the ports will raise the warning by blinking. Loop Prevention When loop is detected, the port will be disabled and turned off the Link/ACT LED of the looped port. Apply Click Apply to save the changes. -
Page 27: Iv-13. Poe
IV-13. PoE Click on a port number and the options are shown below: Click the drop down menu to select whether to Turn on or Turn off PoE function. Click “Apply” to apply the settings. -
Page 28: Iv-14. Password
IV-14. Password In this page you can change the user name and password. Click the “Confirm” button to save the changes. IV-15. Logout Click the Logout button to exit the Web Management UI of GS-5210PLG. -
Page 29: Safety Instructions
V. Safety Instructions The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details. This product is designed for indoor use only. ... - Page 30 COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.
- Page 31 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 32 EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/30/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/30/EU.
- Page 33 Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: 9-port Gigabit + 1-port SFP Smart-lite Ethernet Switch w/ 8 PoE+ ports Model No.: GS-5210PLG...
- Page 34 Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the United Kingdom EMC and Safety directives. Equipment: 9-port Gigabit + 1-port SFP Smart-lite Ethernet Switch w/ 8 PoE+ ports Model No.: GS-5210PLG...
Need help?
Do you have a question about the GS-5210PLG and is the answer not in the manual?
Questions and answers