Summary of Contents for Thermo Scientific Auto Sample Changer 6
Page 1
Np Pu Am Cm Bk Cf Es Fm Md No Lr Thorium Protactinium Uranium Neptunium Plutonium Americium Curium Berkelium Californium Einsteinium Fermium Mendelevium Nobelium Lawrencium Thermo Scientific ASC6 Auto Sample Changer 6 Instruction Notice AA83863 - A • October 2019...
Contents Revision Table....................Introduction ....................... Safety ......................... General Safety Guidelines ................... Hazard Statements and Symbols ................. The Sample Holder Description ............... Installation ......................Install the ASC6 in ARL EQUINOX ..............Connections to the Power Supply ................ Setting of the Incident Angle ................Sample Preparation Procedure..............
The information in this document is subject to change without notice. We assume no responsibility for any errors that may appear in this document. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 3...
If you need any help, please contact the local Thermo Fisher Scientifi c representative. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 4...
Page 5
Chapter | Introduction Manufacturer THERMO FISHER SCIENTIFIC INEL SAS 71 rue d’Orléans 45410 ARTENAY, FRANCE Tel : +33(0)2-38-80-45-45 Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 5...
Transport of the sample holder should be done with extreme care. • Never operate a damaged sample holder. • Never operate the sample holder with a damaged power cord. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 6...
DANGER! A danger message indicates a risk of injury. In this case the risk concerns the hand or finger. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 7...
Chapter | The Sample Holder Description The Sample Holder Description The ASC6 (Auto Sample Changer 6) sample holder enables to analyze automatically 6 powder samples in reflection mode. 1- 30 mm diameter axis 2- Incidence angle indicator 3- SUB D 9 Connector for the power supply...
The sample holder is equipped with a positioning pin to avoid any position mistake and an incidence angle indicator to read the incidence angle. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 9...
Page 10
1- Reading indicator 2- Incidence angle equal to 0° 3- Medium line 10° of incidence angle 4- Short line 2° of incidence angle Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 10...
The surface of the powder must not exceed the level of the surface of the powder mount, in order to avoid line displacement error due to height error. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 11...
1 (see the picture below). Insert the cup on the sample holder by pushing down and laterally in order that the cup is in analysis position. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 12...
Page 13
Chapter | Sample Preparation Procedure ASC6 with the six samples ready to be inserted in the ARL EQUINOX 100. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 13...
The sample holder can be cleaned with a soft and dry duster. The sample positioning platform can be cleaned with a moist duster or with some domestic alcohol. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 14...
Check the state of the power supply cord, be sure it is properly plugged in. • Check if the software driver is properly installed. • If the problem persists, contact Thermo Fisher Scientific. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 15...
• EN 61326-1 (2013): Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements. Confidential, limited rights Instruction Notice, Auto Sample Changer 6 PN AA83863 | Revision A | 7-Oct-2019 Page 16...
Need help?
Do you have a question about the Auto Sample Changer 6 and is the answer not in the manual?
Questions and answers