Download Print this page
YOKOGAWA Vigilantplant SmartDac GM-10 Firmware Update
YOKOGAWA Vigilantplant SmartDac GM-10 Firmware Update

YOKOGAWA Vigilantplant SmartDac GM-10 Firmware Update

Hide thumbs Also See for Vigilantplant SmartDac GM-10:

Advertisement

Quick Links

GM10
– Main Unit and Modules
Firmware Update
Copyright © 2014 Yokogawa Electric Corporation All Right Reserved
- 1 -

Advertisement

loading
Need help?

Need help?

Do you have a question about the Vigilantplant SmartDac GM-10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for YOKOGAWA Vigilantplant SmartDac GM-10

  • Page 1 GM10 – Main Unit and Modules Firmware Update Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 1 -...
  • Page 2 Summary of Steps to update GM-10 firmware. 1) Update firmware of the main unit. 2) Establish communication (between PC and the GM). 3) Update firmware of the modules. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 2 -...
  • Page 3: Firmware Update

    ● The following error message will be shown alternately in the GM. E5 , 59 This indicates completion of the procedure to update the main GM10 unit. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 3 -...
  • Page 4 Install IP address configuration software to PC. Connect the PC and GM using LAN cable. Launch the IP address configuration software. Find GM in the network. Assign appropriate IP address to the GM. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 4 -...
  • Page 5 ● Make sure that all the module configuration of the GM is correct. (e.g. location of ex-communication module, dip switch setting of the ex- communication module) ● Power ON all the GM and its sub units. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 5 -...
  • Page 6 (3) Update firmware of the I/O modules. Update procedure ● Launch web browser ● Type in IP address (e.g. http://192.168.1.1/ ● Select ‘Calib’ Tab and choose Update Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 6 -...
  • Page 7 (3) Update firmware of the I/O modules. ● Press Next button (lower right of the window) and confirm with OK Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 7 -...
  • Page 8 (3) Update firmware of the I/O modules. ● Mode Switching in progress message is displayed. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 8 -...
  • Page 9 (3) Update firmware of the I/O modules. ● Select ‘Module’ from Update Mode. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 9 -...
  • Page 10 (3) Update firmware of the I/O modules. ● Select NEXT in the bottom right corner and then Update. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 10 -...
  • Page 11 (3) Update firmware of the I/O modules. ● Updating (All modules) message will be displayed. ● When completed the Update Completed message will display. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 11 -...
  • Page 12 ● After completion , select END and apply reconfiguration (from ‘Calib’ tab) ● Select Exit current mode and OK. ● Repeat above procedure if Sub unit is used. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 12 -...
  • Page 13 (3) Update firmware of the I/O modules. ● Select Reconfiguration and all modules should display BLUE. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 13 -...
  • Page 14 Outdated firmware module – for status Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 14 -...
  • Page 15 Module after firmware update – BLUE status Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 15 -...
  • Page 16 Now, that’s SMART. Copyright © 2014 Yokogawa Electric Corporation All Right Reserved - 16 -...