Table of Contents
Advertisement
Column 1
Feature Select
1st latched
Row 1
Sound 1: on/off
1st momentary
info on page 18
Row 2
Sound 2: on/off
2nd momentary
info on page 18
Row 3
Sound 3: on/off
3rd momentary
info on page 18
Row 4
Sound 4: on/off
4th momentary
info on page 18
Row 5
Sound 5: on/off
5th momentary
info on page 18
Row 6
Sound 6: on/off
6th momentary
info on page 18
WARNING:
If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING; it requires installer-only adjustment. Changing the duration may cause damage.
NOTE 1:
Transmit channel 1 (or other channel of your choosing) of the new remote control.
You will hear two chirps to indicate that the code has been accepted and recorded.
Transmit channel 2 (or other channel of your choosing) of the new remote control.
NOTE 2:
You will hear two chirps to indicate that the code has been accepted and recorded.
Transmit channel 3 (or other channel of your choosing) of the new remote control.
NOTE 3:
You will hear two chirps to indicate that the code has been accepted and recorded.
Transmit channel 4 (or other channel of your choosing) of the new remote control.
NOTE 4:
You will hear two chirps to indicate that the code has been accepted and recorded.
Transmit channel 5 (or other channel of your choosing) of the new remote control.
NOTE 5:
You will hear two chirps to indicate that the code has been accepted and recorded.
When you hear the two chirps, all remote control codes will have been erased from
NOTE 6:
system memory. You must now add the new and/or existing remote controls to the system
(i.e., program channels 1–5 of each remote that will be used with your Concept 50).
NOTE 7:
Turn off the ignition, exit the vehicle (taking the keys with you) and close the doors.
Firmly "thump" the window pillar with the side of your fist. You should hear a chirp to
confirm activation of the sensor's main zone. Use remote control button 2 to increase
sensitivity, button 4 to decrease. Repeat until the sensor is set to the sensitivity you wish,
then press remote control button 1 to end programming mode.
Use the same procedure as NOTE 7, but strike the window pillar lightly.
NOTE 8:
Matrix of user-selectable features
Column 2
Column 3
2nd latched
3rd latched
Add new remote to
Test/adjust primary (normal)
channel 1 (arm/disarm)
zone of vibration sensor
info on page 9–10 & 23
info on pages 13–14
NOTE 1
NOTE 7
Add new remote to
Test/adjust secondary (high)
channel 2 (trunk/timer)
zone of vibration sensor
info on page 9–10 & 23
info on pages 13–14
NOTE 2
NOTE 8
Add new remote to
Test/adjust glass
channel 3 (silent
tampering sensor
arm/disarm)
info on pages 13–14
info on page 9–10 & 23
NOTE 9
NOTE 3
Add new remote to
channel 4 (accessory 1)
Pulsed/constant ground
info on page 9–10 & 23
output upon panic
NOTE 4
Add new remote to
channel 5 (accessory 2)
Headlight Reminder: on/off
info on page 9–10 & 23
info on page 16
NOTE 5
Erase all channels
FACT: on/off
info on page 9–10 & 23
info on page 15
NOTE 6
Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these setting.
Column 4
Column 5
4th latched
5th latched
QuietChirps: on/off
Anti-carjacking: on/off
info on page 18
info on page 7–8
Remote control button/channel
Long-term
sequence for anti-carjacking
chirp silencing: on/off
info on page 8
info on page 18
Add a dedicated
15-second entry delay: on/off
anti-carjacking remote control
info on page 12
info on page 8
AutoLock/UnLock: on/off
info on page 17
Smart AutoArming: on/off
Siren duration: 30/60 sec.
info on page 12
info on page 18
Set a new secret
AutoArm & Lock: on/off
disarming/valet code
info on page 12
info on pages 7–8 & 13
NOTE 9:
Use the same procedure as NOTE 7, but firmly tap a coin (such as a quarter) against
the window to test sensitivity.
Transmit the first channel of your choice (any channel from 1–12). You will hear a
NOTE 10:
one-chirp confirmation. Transmit the second channel of your choice (again, any channel you
wish from 1–12). You will hear a two-chirp confirmation. You may now use this
combination to turn off the 20-second anti-carjacking countdown.
NOTE 11:
Transmit the channel of your choice on the dedicated anti-carjacking remote
control. You will hear two chirps to indicate that that remote control button will now turn
off the 20-second anti-carjacking countdown. Be sure to carry this remote on your person,
since a carjacker will undoubtedly take your usual remote control and purse.
NOTE 12:
Immediately flip the switch to its latched position, then enter the new code that
you wish to use. Make sure to return the switch to its center position when complete, then
wait 3 seconds (you will hear two chirps when the system has accepted the new code). Turn
the ignition off. VERY IMPORTANT: You must immediately test your new secret
disarming/valet code: Turn the ignition on, enter your new code, then flip the switch to its
latched position. The LED will illuminate. If it does not, the new code you programmed and
the one you just entered do not match. The system has reverted to the previous code.
The timer starts as soon as you enable this feature (6 latches, 1 momentary). When
NOTE 13:
the duration you wish has been reached, press button 1 on the remote control. You will hear two
chirps to confirm the new duration.
Column 6
6th latched
Headlight timer: 1sec–2.5min (30sec)
info on pages 11 & 17
NOTE 13
RPM monitoring: on/off
NOTE 10
Factory-delayed
courtesy lights: on/off
NOTE 11
Channel 4 output:
Set idle RPM
pulsed/latched/timed
Channel 5 output:
pulsed/latched/timed
QuickAccess valet mode: on/off
info on page 16
NOTE 12
Advertisement
Table of Contents
