Declaration Of Conformity - V2 Sirmo-Digit Manual

Digital switch

Hide thumbs Also See for Sirmo-Digit:

Manual (10 pages)

Table Of Contents

Table of Contents

Available languages

Customization of the access code

OPERATIONS TO BE MADE ON THE KEYPAD

1. Key in # + PROGRAMMING CODE + #

Signalling: 1 BEEP of 1,5 sec. + L1 and L2 on for 1,5 sec.

2. Key in within a minute the KEY 2 + #

Signalling: 2 BEEP + L2 on

3. Key in the NUMBER OF THE CHOSEN CHANNEL + #

Signalling: 1 BEEP of 1 sec. + L2 on

4. Key in the NEW ACCESS CODE + #

Signalling: 1 BEEP of 1 sec. + L2 on

5. Repeat the NEW ACCESS CODE + #

Signalling:

- 1 BEEP of 3 sec. + L1 and L2 on if the

operation is correct;

- short flashes of the LED if incorrect

Disabling a channel

OPERATIONS TO BE MADE ON THE KEYPAD

1. Key in # + PROGRAMMING CODE + #

Signalling: 1 BEEP of 1,5 sec. + L1 and L2 on for 1,5 sec.

2. Key in within a minute the KEY 2 + #

Signalling: 2 BEEP + L2 on

3. Key in the NUMBER OF THE CHOSEN CHANNEL + #

Signalling: 1 BEEP of 1 sec. + L2 on

4. Key in the KEY 0 + #

Signalling: 1 BEEP of 1 sec. + L2 on

5. Repeat the KEY 0 + #

Signalling:

- 1 BEEP of 3 sec. + L1 and L2 on if the

operation is correct;

- short flashes of the LED if incorrect

3. WORKING MODE: ROYAL, 53200 or

PERSONAL PASS

Select the working mode according to the kind of remote

controls already used in the system.

OPERATIONS TO BE MADE ON THE KEYPAD

1. Key in # + PROGRAMMING CODE + #

Signalling: 1 BEEP of 1,5 sec. + L1 and L2 on for 1,5 sec.

2. Key in within a minute the KEY 3 + #

Signalling: 3 BEEP + L1 and L2 on

3. •

Key in the KEY 1 + # to select ROYAL mode

•

Key in the KEY 2 + # to select 53200 mode

•

Key in the KEY 3 + # to select PERSONAL PASS mode

Signalling: 1 BEEP of 1 sec.

4. Repeat to confirm (1 + # or 2 + # or 3 + #)

Signalling:

- 1 BEEP of 3 sec. + L1 and L2 on if the

operation is correct;

- short flashes of the LED if incorrect

4. DIP-SWITCH CODE (only version Royal/53200)

The factory dip-switch code set for channel 1 is 0101010101 00.

If other remote controls are already stored on the receiver, the

dip-switch code of the keypad has to be set with the same

sequence of the one set on the dip-switch of the remote control.

The dip-switch of the remote control is made up by a series of 12

micro switches set to ON or OFF.

To set the same code on the keypad, it is necessary to key in a

code made up of 12 digits: those will be 0 or 1, depending on

the position of the micro switches on the remote control

micro switch set to ON = 1

micro switch set to OFF= 0

If the transmitter is single channel, the dip-switch to be set

coincides with the position of the 12 micro switches.

If the transmitter is two-channel and the key stored is 2, the

dip-switch code to be set coincides with the position of the 12

micro switches. If the key stored on the receiver is the key 1, the

dip-switch code coincides with the position of the micro switches

from 1 to 10 plus the 2 digit 00.

If the transmitter is four-channel, the dip-switch code to be

set coincides with the position of the micro switches from 1 to 10

plus 2 digits, which are:

•

00 if the key stored on the receiver is the key 1

(e.g. 1010101010 00)

•

10 if the key stored on the receiver is the key 2

(e.g. 1010101010 10)

•

01 if the key stored on the receiver is the key 3

(e.g. 1010101010 01)

•

11 if the key stored on the receiver is the key 4

(e.g. 1010101010 11)

If no transmitter has been stored on the receiver, the

dip-switch code can be set entering a random sequence of 12

digits 0 or 1.

OPERATIONS TO BE MADE ON THE KEYPAD

1. Key in # + PROGRAMMING CODE + #

Signalling: 1 BEEP of 1,5 sec. + L1 and L2 on for 1,5 sec.

2. Key in within a minute the KEY 4 + #

Signalling: 4 BEEPs + L1 and L2 flashing alternately

3. Key in the NUMBER OF THE CHOSEN CHANNEL + #

Signalling: 1 BEEP of 1 sec. + L1 and L2 flashing alternately

4. Key in the CHOSEN DIP-SWITCH CODE + #

Micro switch set to ON = 1

Micro switch set to OFF = 0

Signalling:

- 1 BEEP of 3 sec. + L1 and L2 on if the

operation is correct;

- short flashes of the LED if incorrect