Figures - ABB XAC22175 Operation Manual

Operation Manual / 4 Product description / A100-L

Figures

Figures
Fig. 1: Layout and function of the turbocharger ...... 4
Fig. 2: Warning plate locations .................................... 6
Fig. 3: Locations of the rating plates .......................... 7
Fig. 4: Fit the lifting gear .............................................. 9
Fig. 5: Placing the turbocharger ................................. 10
Fig. 6: Compressor-end foot....................................... 11
Fig. 7: Turbine-end foot................................................ 11
Fig. 8: Oil temperature at the outlet.......................... 17
Fig. 9: Layout and overview of the speed measure-
ment system................................................................... 19
Fig. 10: Replacing the speed sensor .......................... 21
Fig. 11: U-tube manometer at the filter silencer...... 22
Fig. 12: Noise insulation, bellows .............................. 24
Fig. 13: Layout and overview of filter silencer ......... 32
Fig. 14: Dismantling filter ring circumferential part....
34
Fig. 15: Opening filter ring lock.................................. 34
Fig. 16: Attaching new filter ring ............................... 35
Fig. 17: Fitting new filter ring ..................................... 35
Fig. 18: Overview of wet cleaning of compressor .. 38
Fig. 19: Filter plug view................................................ 39
Fig. 20: Overview of dry cleaning device................... 41
Fig. 21: Drain pipe diagram......................................... 44
Fig. 22: Weights of assemblies ................................. 53
Fig. 23: Dismantling the filter silencer casing ........ 54
Fig. 24: Fitting the filter silencer casing .................. 55
Fig. 25: Fitting the filter silencer casing ................. 56
Fig. 26: Fitting the filter silencer casing ................. 56
Fig. 27: Fitting the filter silencer casing ................... 57
Fig. 28: Fitting the filter silencer casing ................... 57
Fig. 29: Fitting the bellows ......................................... 58
Fig. 30: Dismantling the filter silencer ..................... 59
Fig. 31: Dismantling the filter silencer...................... 60
© Copyright 2020 ABB. All rights reserved.
Fig. 32: Dismantling the filter silencer with noise
package ........................................................................... 61
Fig. 33: Pressing off compressor casing................... 62
Fig. 34: Moving out wall insert .................................... 63
Fig. 35: Putting down wall insert ................................ 63
Fig. 36: Putting down wall insert ................................ 64
Fig. 37: Dismantling the diffuser ............................... 65
Fig. 38: Measuring axial clearance A .......................... 66
Fig. 39: Removing the insulation (A175-L and smal-
ler)..................................................................................... 67
Fig. 40: Dismantling the gas inlet casing (A175-L and
smaller) - screwed variant ........................................... 68
Fig. 41: Dismantling the gas inlet casing (A175-L and
smaller) - threaded stud variant ................................ 69
Fig. 42: Dismantling the nozzle ring (A175-L and
smaller) ............................................................................ 70
Fig. 43: Dismantling the gas inlet casing (A180-L and
larger) - screwed variant............................................... 71
Fig. 44: Dismantling the gas inlet casing (180-L and
larger) - threaded stud variant ................................... 72
Fig. 45: Fitting the nozzle ring holder........................ 73
Fig. 46: Dismantling the nozzle ring .......................... 74
Fig. 47: Put down the nozzle ring................................ 74
Fig. 48: Fitting the nozzle ring (A175-L and smaller) ...
75
Fig. 49: Fitting the gas inlet casing (A175-L and
smaller) - screwed variant ........................................... 76
Fig. 50: Fitting the gas inlet casing (A175-L and
smaller) - threaded stud variant ................................ 77
Fig. 51: Fitting the insulation (A175-L and smaller). 78
Fig. 52: Looping around the nozzle ring (A180-L and
larger)............................................................................... 79
Fig. 53: Fitting the nozzle ring (A180-L and larger). 80
Fig. 54: Fitting the gas inlet casing (A180-L and lar-
ger) - screwed variant .................................................. 81
Fig. 55: Fitting the gas inlet casing (A180-L and lar-
ger) - threaded stud variant........................................ 82
Fig. 56: Measuring axial clearance A .......................... 83
Fig. 57: Fitting the diffuser .......................................... 84
HZTL4034_EN Revision P January 2020