Table of Contents
Advertisement
Quick Links
INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS
Contents
1.
INTRODUCTION ....................................................................................................................................... 2
2.
PRODUCT WARNINGS ............................................................................................................................ 2
3.
PRODUCT RATINGS ................................................................................................................................ 2
WHAT'S INCLUDED .................................................................................................................................. 3
4.
5.
OVERVIEW ............................................................................................................................................... 3
6.
BATTERIES AND CHARGER ................................................................................................................... 4
6.1
Charging Batteries ............................................................................................................................ 4
6.2
Installing Batteries ............................................................................................................................. 4
6.3
Storing Batteries................................................................................................................................ 5
6.4
Disposing of Batteries ....................................................................................................................... 5
6.5
Safety ................................................................................................................................................ 5
7.
INTEGRATED PRESSURE TRANSDUCER............................................................................................. 6
SYNCING THE SAM™ SMART NOZZLE TO THE SAM™ TRUCK ........................................................ 6
8.
PAIRING THE SAM™ SMART NOZZLE TO A DISCHARGE VALVE ...................................................... 8
9.
UN-PAIRING THE SAM™ SMART NOZZLE FROM A DISCHARGE VALVE .................................... 11
10.
CHARGING THE HOSE FROM THE SAM™ SMART NOZZLE ......................................................... 12
11.
12.
LOSS OF SIGNAL ............................................................................................................................... 13
13.
TANK LEVEL INDICATION AND PERMANENT WATER SUPPLY (HYDRANT) ............................... 14
14.
DISPLAY LED INTENSITY LEVELS AND RESETTING ..................................................................... 15
15.
CHECKING BATTERY CHARGE LEVEL ............................................................................................ 15
UPDATING THE SAM™ SMART NOZZLE FIRMWARE .................................................................... 16
16.
16.1
Equipment needed .......................................................................................................................... 16
16.2
Setup and Test Procedure .............................................................................................................. 16
16.3
Using the Web Browser .................................................................................................................. 16
16.4
SAM Nozzle Configuration (Standard Mode) .................................................................................. 17
16.4.1
Setting the Active Time ........................................................................................................... 18
16.4.2
Specifying the LED Intensity ................................................................................................... 20
16.4.3
Examining Other Configuration Details ................................................................................... 23
16.5
Updating the Wi-Fi Firmware .......................................................................................................... 26
16.6
Updating the Host Processor Firmware .......................................................................................... 30
17.
FREQUENTLY ASKED QUESTIONS ................................................................................................. 34
18.
REPLACEMENT PARTS ..................................................................................................................... 34
19.
WARRANTY STATEMENT .................................................................................................................. 34
Sheet: 128570
SAM™ SMART NOZZLE N
PHONE: 800.228.1161
www.akronbrass.com
Revision 06/28/2022
P
2
Page: 1 of 34
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Akron SAM N2P
Summary of Contents for Akron SAM N2P
-
Page 1: Table Of Contents
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS Contents INTRODUCTION ............................2 PRODUCT WARNINGS ..........................2 PRODUCT RATINGS ..........................2 WHAT’S INCLUDED ..........................3 OVERVIEW ............................... 3 BATTERIES AND CHARGER ........................4 Charging Batteries ..........................4 Installing Batteries ..........................4 Storing Batteries.......................... -
Page 2: Introduction
Operational range: 10 feet (3.048 m) • Dimensions less Akron Brass nozzle and inlet: 5” (12.7 cm) L x 2-1/2” (6.4 cm) W x 4-5/32” (10.7 cm) H Transmission at this power level is for less than 20 ms for each SAM nozzle poll response. -
Page 3: What's Included
Battery charger P/N 60470010 5. OVERVIEW The SAM™ SMART NOZZLE module is an integrated unit mounted to the inlet of Akron Brass Company handline nozzles. The nozzles which the SAM™ SMART NOZZLE module can be mounted to include the Turbojet™, Assault™, and Pyrolite shutoffs. The specified operating pressure can be 50, 75, or 100 psi depending on the nozzle and customer requirements. -
Page 4: Batteries And Charger
The SAM™ SMART NOZZLE comes with Akron Brass P/N 803435 Lithium-ion rechargeable batteries. The batteries must be fully charged prior to first use. Akron Brass recommends using the Tenergy TN471U battery charger. Akron Brass internal P/N for this charger is 60470010. -
Page 5: Storing Batteries
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS Batteries (2) Cover Plate Thumbscrew Cover Plate 6.3 Storing Batteries When batteries won’t be used for longer than one month, they should be stored in a cool, dry place and at 40% charge. -
Page 6: Integrated Pressure Transducer
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS ▪ Using any battery other than Akron Brass P/N 803435 can potentially damage your SAM™ SMART NOZZLE. Failure to do this increases the chance of fire and will void your warranty. - Page 7 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS process. Upon detecting the SAM™ SMART NOZZLE radio in the truck the SAM™ SMART NOZZLE will begin the process of synchronization between the two devices. The LEDs on the SAM™ SMART NOZZLE will toggle while displaying the color green as shown below.
-
Page 8: Pairing The Sam™ Smart Nozzle To A Discharge Valve
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS If for any reason a SAM™ SMART NOZZLE that has been sync’d with the SAM™ truck cannot locate the truck radio, the LED display of the SAM™ SMART NOZZLE will indicate as shown below in a red, yellow, green sequence. - Page 9 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS When ready to pair the SAM™ SMART NOZZLE with a discharge valve, SIMULTANEOUSLY press and hold the two function buttons located on either side of the SAM™ SMART NOZZLE module for a minimum time of 2 seconds.
- Page 10 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS At the completion of the pairing process, the LEDs will display a successful pair or a failed pair attempt, as shown below. Two blue flashing LEDs denote a successful pair process and the SAM™ SMART NOZZLE is now paired with a specific discharge valve on the SAM™...
-
Page 11: Un-Pairing The Sam™ Smart Nozzle From A Discharge Valve
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 10. UN-PAIRING THE SAM™ SMART NOZZLE FROM A DISCHARGE VALVE The truck pump must be in the disengaged mode (road mode) to unpair the SAM™ SMART NOZZLE from a discharge valve on the SAM™ truck. Failure to do so may cause unintentional activation of discharge valves on the truck. -
Page 12: Charging The Hose From The Sam™ Smart Nozzle
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS Upon seeing that the SAM nozzle has successfully unpaired, press the “SEND BAM” button at the bottom of the pairing screen on the UV1100. A pop-up window will appear, asking if you wish to continue. Click the check mark button to proceed. -
Page 13: Loss Of Signal
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 12. LOSS OF SIGNAL The SAM™ SMART NOZZLE uses a wireless communication method to remain in contact with the SAM™ system on the truck. If for any reason that communication is lost while in pump mode, the LED display on the SAM™... -
Page 14: Tank Level Indication And Permanent Water Supply (Hydrant)
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 13. TANK LEVEL INDICATION AND PERMANENT WATER SUPPLY (HYDRANT) Tank level indication on the SAM™ SMART NOZZLE are visible only when the pump is engaged (pump mode). The SAM™ SMART NOZZLE LED display provides information on the amount of water in the tank on the truck. -
Page 15: Display Led Intensity Levels And Resetting
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 14. DISPLAY LED INTENSITY LEVELS AND RESETTING The SAM™ SMART NOZZLE LED display is adjustable from LOW-MEDIUM-HIGH LED intensity levels. The nozzle comes from the factory preset at LOW intensity. LED intensity level is adjusted at the UV1100 screen. To change the intensity setting reference the UV1100 instructions. -
Page 16: Updating The Sam™ Smart Nozzle Firmware
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 16. UPDATING THE SAM™ SMART NOZZLE FIRMWARE The SAM™ SMART NOZZLE is equipped with an internal Wi-Fi radio to allow wireless firmware updates when they are needed or become available during firmware upgrades. 16.1 Equipment needed 1. -
Page 17: Sam Nozzle Configuration (Standard Mode)
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS To configure adaptable parameters or to observe available diagnostic conditions, select the link to “6055 SAM Nozzle” from the akronbrass.net home page. The arrow ( ) indicates what hyperlink text or button to select at each step, for the given examples, or points out a key difference(s) in a given step. -
Page 18: Setting The Active Time
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 16.4.1 Setting the Active Time The Active Time parameter specifies the length of time the SAM™ SMART NOZZLE will stay awake (i.e., not enter its “sleep” state) between button presses under the following conditions: •... - Page 19 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 19 of 34...
-
Page 20: Specifying The Led Intensity
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 16.4.2 Specifying the LED Intensity The LED Intensity parameter sets the brightness level of the LEDs on the SAM™ SMART NOZZLE display. There are three options available—Low, Medium, High—with Low being the default value. Follow the images below to see how to change the LED Intensity. - Page 21 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 21 of 34...
- Page 22 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 22 of 34...
-
Page 23: Examining Other Configuration Details
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 16.4.3 Examining Other Configuration Details The operator can click on the tabs to the right of the Main tab to view other details of the SAM™ SMART NOZZLE’s configuration. This includes pressure, SAM-related, and wireless communication-related information. - Page 24 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 24 of 34...
- Page 25 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 25 of 34...
-
Page 26: Updating The Wi-Fi Firmware
SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 16.5 Updating the Wi-Fi Firmware To update the firmware in the Wi-Fi module on the SAM™ SMART NOZZLE board, click on the hyperlink named “Wi-Fi Module FW Update” on the akronbrass.net home page. PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570... - Page 27 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 27 of 34...
- Page 28 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 28 of 34...
- Page 29 SAM™ SMART NOZZLE N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 29 of 34...
-
Page 30: Updating The Host Processor Firmware
SAM™ SMART NOZZLE N2P INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS Upon updating the firmware, cycle power on the SAM™ SMART NOZZLE. (The Wi-Fi connection will be terminated.) 16.6 Updating the Host Processor Firmware To update the firmware in the main processor on the SAM™ SMART NOZZLE board, click on the hyperlink named “Wi-Fi Host FW Update”... - Page 31 SAM™ SMART NOZZLE P2N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 31 of 34...
- Page 32 SAM™ SMART NOZZLE P2N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 32 of 34...
- Page 33 SAM™ SMART NOZZLE P2N INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS Upon updating the firmware, cycle power on the SAM™ SMART NOZZLE. (The Wi-Fi connection will be terminated.) PHONE: 800.228.1161 www.akronbrass.com Sheet: 128570 Revision 06/28/2022 Page: 33 of 34...
-
Page 34: Frequently Asked Questions
Akron Brass. Products must be promptly returned to Akron Brass for warranty service. We will not be responsible for: wear and tear; a failure due to having used any battery in the SAM™ SMART NOZZLE other than Akron Brass P/N 803435, any improper installation, use, maintenance or storage;...
Need help?
Do you have a question about the SAM N2P and is the answer not in the manual?
Questions and answers