Page 1 AX1800 Wi-Fi 6 ADSL2/VDSL2+ Modem Router with VoIP DSL-X1852E • Wi-Fi 6 (802.11ax) technology provides faster speeds, greater capacity and less network congestion • Wi-Fi speeds up to 1.8 Gbps (600 + 1200Mbps) built for the modern device-dense Smart Home •...
Page 2 AX1800 Wi-Fi 6 ADSL2/VDSL2+ Modem Router with VoIP The DSL-X1852E may not support all of the mandatory features, established in Wave 1 of the IEEE 802.11ax specifications Maximum wireless signal rate derived from IEEE Standard 802.11ax specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, may lower actual data throughput rate.
Page 3 User Manual AX1800 Wi-Fi 6 VDSL2/ADSL2+ Modem Router with VoIP DSL-X1852E...
Page 4: Preface
Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Page 5: Table Of Contents
USB ...................58 Internet ...................22 USB Modem ..............59 IPv4/IPv6 ................23 Port Bind ................60 DSL ..................24 QoS...................61 4G ..................25 Features ..................63 VPN ..................26 Firewall ...................63 DSL-X1852E ................27 IPv4/IPv6 Filter ..............64 Connected Clients ..............28 NAT ..................66 USB Device ................29 D-Link DSL-X1852E User Manual...
Page 6 Connect and Share a USB Storage Device .....93 Connecting from a Windows-Based PC ......94 Connect and Share with DLNA Devices ......97 Accessing from File Explorer on Windows ....98 Connect a Wireless Client to Your Router .....100 D-Link DSL-X1852E User Manual...
Page 7: Product Overview
Quick Install Guide If any of the above items are missing, please contact your reseller. Note: Using a power supply other than the one included with the DSL-X1852E may cause damage and void the warranty for this product. D-Link DSL-X1852E User Manual...
Page 8: System Requirements
• Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Browser Requirements: Utility Requirements • Internet Explorer 7 or higher • Firefox 23 or higher • Safari 7 or higher • Chrome 28 or higher • Microsoft Edge D-Link DSL-X1852E User Manual...
Page 9: Introduction
Section 1 - Product Overview Introduction The D-Link AX1800 Wi-Fi 6 VDSL2/ADSL2+ Modem Router with VoIP augments your smart home connectivity by leveraging the latest DSL technology. Not only can multiple devices share a single Internet connection, your phones can now use the same Internet access while these devices are transmitting data over the Internet, saving cost and offering convenience through Internet telephony.
Page 10 Section 1 - Product Overview virtual links between two endpoints. • Remote Management - The DSL-X1852E can be remotely provisioned with configuration profiles uploaded by service providers, eliminating on-site management and reducing time for large-scale deployment. * Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n, 802.11ac, and 802.11ax specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Page 11: Hardware Overview
5 seconds. During the reset process, all lights will turn off and back on again. Power Button Power on/off switch. Power Connector Connector for the supplied power adapter. USB 3.0 Port Connects to USB flash drives to share content. D-Link DSL-X1852E User Manual...
Page 12 Connects to Ethernet devices such as computers, switches, storage (NAS) devices and game Ports (1-4) consoles at speeds of up to 1000 Mbps.. WAN Port Connects to a cable/DSL (or NBN™/UFB) modem or connection box. DSL Port Connects to a DSL-enabled telephone line. D-Link DSL-X1852E User Manual...
Page 13: Leds
LAN port. Off indicates the LAN port is not connected. Solid green Wireless Lights up green when the 2.4 or 5 GHz wireless network is enabled. Flashes green when Blinking green 2.4G/5G there is wireless activity. Off indicates wireless function is disabled. D-Link DSL-X1852E User Manual...
Page 14 Lights up green when the phone port has an active connection to an Internet phone service. FXS 1/2 Blinking green It flashes green when the phone is in use. Off indicates that the port is not connected or the phone has no Internet phone service. D-Link DSL-X1852E User Manual...
Page 15: Installation
• If you are connecting a considerable amount of networking equipment, it may be a good idea to take the time to label each cable or take a picture of your existing setup before making any changes. • We suggest setting up your DSL-X1852E from a single device and verifying that it is connected to the Internet before connecting additional devices.
Page 16: Wireless Installation Considerations
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapter’s range from 3 to 90 feet (1 to 30 meters.) Position your devices so that the number of walls or ceilings is minimized.
Page 17: Manual Setup
Manual Setup Note: Power off your network devices, including your existing connection box/modem and PC. Position your DSL-X1852E near your PC and a telephone wall jack that provides DSL service. Keep the router in an open area for better wireless coverage.
Page 18 WALL JACK Use the DSL-X1852E as a router only. Plug one end of the supplied Ethernet cable into the WAN port on the back of the router and the other end to your existing cable/UFB/NBN™ connection box or modem. Then power on the connection box.
Page 19 Ethernet port on your computer. If you are setting up the DSL-X1852E using a laptop or mobile device, connect to it using the Wi-Fi network name and password printed on the label attached to the bottom of your device.
Page 20: Getting Started
There are two ways you can configure your router to connect to the Internet and connect to your clients: • D-Link Setup Wizard - This wizard will launch when you log into the router for the first time. Refer to Setup Wizard on page 15.
Page 21: Setup Wizard
The wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Depending on your Internet service and network environment, ensure that your DSL port is connected to the wall jack or an Ethernet WAN port is connected to an active Internet connection.
Page 22 Connection Type if asked, and click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. D-Link DSL-X1852E User Manual...
Page 23 Section 3 - Getting Started Setup Wizard (continued) If you selected Static IP Address, enter the IP address, subnet mask, gateway address, and DNS servers provided by your ISP, then choose the Connection Type if asked. Click Next to continue. D-Link DSL-X1852E User Manual...
Page 24 If the router detected or you selected Dynamic IP Address (DHCP), choose the Connection Type if asked. Click Next to continue. If you selected Bridge Mode, choose the Connection Type if asked. Click Next to continue. D-Link DSL-X1852E User Manual...
Page 25 Click Next to continue. Passwords must contain 6 to 32 alphanumeric characters including a mix of uppercase and lowercase letters, numbers, and special characters with the exception of the following characters: '-;`=%+&|><"/. D-Link DSL-X1852E User Manual...
Page 26 Back to make changes to your configurations. The wizard will close and your settings will be saved. Congratulations, setup is complete. You can access the Setup Wizard again from the web configuration utility: go to Settings > Wizard. D-Link DSL-X1852E User Manual...
Page 27: Configuration
Home The Home page displays the current status of the router in the form of an interactive diagram. There are four main sections: Internet, the DSL-X1852E, Connected Clients, and USB Device. You can click each icon to display information about each section at the bottom of the screen. The menu bar at the top of the page will allow you to quickly navigate to the Settings, Features, and Management functions.
Page 28: Internet
If your Internet is disconnected, indicated by a red X, you can launch the Setup Wizard to correct the issue by clicking Wizard from the Settings menu at the top of the page. To reconfigure the Internet settings, refer to Internet on page 30. D-Link DSL-X1852E User Manual...
Page 29: Ipv4/Ipv6
Prefix identifies the subnet of a network in IPv6 addressing scheme. Primary DNS Displays the current primary DNS server. Server: Secondary DNS Displays the current secondary DNS server. Server: Click Go to Settings below to go to the Internet configuration page. D-Link DSL-X1852E User Manual...
Page 30: Dsl
Displays the output power of the DSL modem. FEC, CRC: These error correction counts are used for diagnostic purposes. If you are having trouble with the connection to your ISP, these values may provide useful information for technicians. D-Link DSL-X1852E User Manual...
Page 31 Displays the current default gateway for the interface. Primary DNS Displays the current primary DNS server. Server: Secondary DNS Displays the current secondary DNS server. Server: Click Go to Settings below to go to the USB Modem configuration page. D-Link DSL-X1852E User Manual...
Page 32: Vpn
Displays the IP address of the VPN server. VPN IP: Displays the IP address used for VPN connection. Connected 172.17.94.53 VPN Gateway: Displays the IP address used for VPN gateway. Click Go to Settings below to go to the VPN configuration page. D-Link DSL-X1852E User Manual...
Page 33: Dsl-X1852E
Section 4 - Configuration DSL-X1852E Click on the DSL-X1852E icon to view details about the router and its wireless settings. Here you can see the router’s current wireless networks settings such as SSID and password, as well as the local area network MAC and IPv4 addresses.
Page 34: Connected Clients
Enable Parental Control and select a profile to control the client's Internet access. Make sure that this device is also on the device list of the selected profile. Go to Features > Parental Control for more information on Parental Control. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 35: Usb Device
To configure your USB settings, click Go to Settings or click Settings > USB to obtain more information on USB configuration. For information on how to access your USB drive from a Windows-based PC refer to Connect and Share a USB Storage Device on page 93. D-Link DSL-X1852E User Manual...
Page 36: Settings
Refer to Setup Wizard on page 15 for more information. Internet The following pages will describe how to connect your DSL-X1852E to the Internet. To access this page, go to Settings > Internet at the top of the page.
Page 37: Internet - Adsl
Internet - ADSL ADSL is one of the first home broadband technologies introduced. ADSL uses the DSL port on your DSL-X1852E to connect to the Internet. In order for your DSL-X1852E to use ADSL, you must configure the WAN Connection Type and related WAN settings.
Page 38 Enable Vlan ID Enable or disable VLAN settings. Vlan ID Enter the VLAN ID. Enter a value from 1 - 4094. To set your IPv4/IPv6 connection parameters of WAN connection, refer to Connection Types on page 35. D-Link DSL-X1852E User Manual...
Page 39: Internet - Vdsl
VDSL is one of the latest and fastest home broadband technologies. VDSL uses the DSL port on your DSL-X1852E to connect to the Internet. In order for your DSL-X1852E to use VDSL, you must configure the WAN Connection Type and related WAN settings.
Page 40: Internet - Ethernet
Your DSL-X1852E is equipped with a multi-purpose Gigabit Ethernet LAN/WAN port which can be used to connect to the Internet. This port can also be used to connect to other Ethernet based networks. In order for your DSL-X1852E to use Ethernet, you must configure the WAN Connection Type and related WAN settings.
Page 41: Connection Types
This option is not available for related voice service types such as VOICE, VOICE_INTERNET, and TR069_VOICE and TR069. Connection Type: Select Bridged IP LLC or Bridged IP VC-Mux as the encapsulation method. This is only available for ADSL. D-Link DSL-X1852E User Manual...
Page 42 Auto or Manual. For Manual, please enter the prefix address, for example 2001:b011:2000:0012::. Enter the prefix information option by specifying preferred lifetime and valid lifetime for the prefix (600- 4294967295 seconds). Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 43: Connection Type: Static Ip
Enter the primary DNS server IP address assigned by your ISP. This Server address is usually obtained automatically from your ISP. Secondary DNS Enter the secondary DNS server IP address assigned by your ISP. This Server address is usually obtained automatically from your ISP. Advanced Settings D-Link DSL-X1852E User Manual...
Page 44 2001:b011:2000:0012::. The prefix is used to determine the subnet prefix of an IPv6 address. Then enter the prefix information option by specifying preferred lifetime and valid lifetime for the prefix (600- 4294967295 seconds). Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 45: Connection Type: Pppoe
Enter the password provided by your ISP. Then enter it again to confirm Password: your entry. Connection Type: Select PPPoE LLC or PPPoE VC-Mux. Advanced Settings MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP. The default is 1500. D-Link DSL-X1852E User Manual...
Page 46 Auto or Manual. For Manual, please enter the prefix address, for example, 2001:b011:2000:0012::. Enter the prefix information option by specifying preferred lifetime and valid lifetime for the prefix (600- 4294967295 seconds). Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 47: Connection Type: Bridge Mode
Section 4 - Configuration Connection Type: Bridge Mode Select Bridge Mode to use the DSL-X1852E as a network bridge to extend an existing network. IPv4 Settings Connection: Select Bridge Mode. Protocol Select IPv4, IPv6 or IPv4/IPv6 for both IPv4 and IPv6 addressing mechanism.
Page 48: Vpn
Internet for all traffic through the WAN interface or to the virtual private network if the VPN is created to facilitate encapsulated and encrypted connections to another network across an existing Internet connection. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 49: Ipsec
Remote IP Enter the IP address of the remote device that can use this tunnel. Address: IP Subnet Mask: Enter the subnet mask if you choose Subnet for Remote Access Range. D-Link DSL-X1852E User Manual...
Page 50 Select 768, 1024, 1536, 2048, 3072, or 4096 bit. Group: Key Life Time: Enter the amount of time that a key is active in Phase 1. Then select the unit: Seconds, Minutes or Hours. Key Exchange Phase 2 D-Link DSL-X1852E User Manual...
Page 51 Key Life Time: Enter the amount of time that a key is active in Phase 2. Then select the unit: Seconds, Minutes or Hours. Click Save when you are done. You can create up to 7 IPSec profiles. D-Link DSL-X1852E User Manual...
Page 52: Gre
Enter the IP address of the remote tunnel network interface. Address: Private Tunnel Enter the private IP address of the remote tunnel. Address: Private Tunnel Enter the subnet mask of the private IP address of the remote tunnel. Netmask: Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 53: Wireless
8 to 63 alphanumeric characters including a mix of uppercase and lowercase letters, numbers and special characters with the exception of the following characters: '-;`=%+&|><"/ . Show Password: Enable or disable display of the above password. D-Link DSL-X1852E User Manual...
Page 54 Refer to WPS Button on page 100 for more information about WPS. Note that WPS will be disabled for security methods other than WPA2. Click Save when you are done. The following pages describe the Advanced Settings configuration options in detail. D-Link DSL-X1852E User Manual...
Page 55 WPA type selected. AES is recommended if other types are presented. Group Key Enter the Group Key Interval as the timing for rekeying the group Interval: temporal key. The default is 3600 seconds. D-Link DSL-X1852E User Manual...
Page 56 Select either Shared or Open. These two types differ in the authentication process before association with an access point. Click Save when you are done. The following pages describe more configuration options in Advanced Settings in detail. D-Link DSL-X1852E User Manual...
Page 57 Channel Width is available if you selected 11N, Mixed 11G/N, Mixed Width: 11N/G/B or Mixed 11AX/G/N for 802.11 Mode. Select 20/40 if you are using 802.11g/b devices or select 20 MHz if you want to disable 40 MHz bandwidth communication. The recommended setting is 20/40. D-Link DSL-X1852E User Manual...
Page 58 The schedule may be set to Always, or you can create your own schedules in the Schedule section. Refer to Time & Schedule on page 83 for more information. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 59: Guest Zone
The schedule may be set to Always, or you can create your own schedules in the Schedule section. Refer to Time & Schedule on page 83 for more information Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 60: Network
Select this option to enable the DHCP server. Server: Enter the following settings to configure your DHCP server: DHCP IP Specify the start and end IP addresses for the range of addresses to Address Range: be assigned by your router. D-Link DSL-X1852E User Manual...
Page 61 If you selected Auto, configure the following settings for DNS: DNS Select: Configure the mode of DNS: Auto, a Service Number of the WAN Interface or Manual and enter the DNS server information manually below. Primary DNS Enter the DNS server's IP address. Server: D-Link DSL-X1852E User Manual...
Page 62 UPnP allows network devices to seamlessly discover each other on the local network for network services such as file sharing and advanced media functions. Select this option to allow UPnP (Universal Plug and Play) on the local network. D-Link DSL-X1852E User Manual...
Page 63: Reserve Ip
Enter an IPv4 address to be assigned. MAC Address: Select a device from the available clients' MAC addresses. Click Apply when you are done to close the screen. Click Save when you are done adding the rules. D-Link DSL-X1852E User Manual...
Page 64: Usb
Enter a password for authentication for access. Click Save when you are done. For information on how to access your USB drive from a Windows-based PC refer to Connect and Share a USB Storage Device on page 93. D-Link DSL-X1852E User Manual...
Page 65: Usb Modem
Enable or disable default route established through your USB modem for Internet connection. NAT: Enable or disable Network Address Translation (NAT). TCP MTU: Enter the Maximum Transfer Unit (100-1492). The default is 0. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 66: Port Bind
The available Service Numbers of the WAN interface are those with a configured VLAN ID. Binding Option: Select the binding port to be bridged to the WAN interface: LAN1- LAN4, WiFi2.4G 1/2, WiFi5G 1/2. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 67: Qos
The rate at which the content is being transferred to the Internet. (Mbps) Download Speed The rate at which the content is being transferred to the router. (Mbps) Click Apply to QoS after the Speed Test to automatically fill in the above information. D-Link DSL-X1852E User Manual...
Page 68 To assign a priority level to a device, click the client and drag and drop to one of the priority categories: Highest, High, or Medium. To change the client's priority, click x on its card to place it back to the Connected Clients. D-Link DSL-X1852E User Manual...
Page 69: Features
Christmas tree attack sends crafted TCP packet to obtain information about the target system. Null scanning In Null Scanning attack, a packet without any flags of the TCP header attack: tries to exploit a system. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 70: Ipv4/Ipv6 Filter
WAN or LAN IP address. Source Subnet Enter the subnet mask of the source IP address for IPv4 addressing Mask/Prefix scheme (four 8-bit octets). Or enter the prefix length for IPv6 Length: addressing scheme (1-128). D-Link DSL-X1852E User Manual...
Page 71 Or enter the prefix length for IPv6 addressing scheme (1-128). Prefix Length: Interface: Select a Service Number of the WAN Interface for which the traffic will pass through. Click Apply to save your settings. A maximum of 20 rules can be defined. D-Link DSL-X1852E User Manual...
Page 72: Nat
VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG off. Please check with the system administrator of your corporate network whether your VPN client supports NAT traversal. D-Link DSL-X1852E User Manual...
Page 73 Allows devices running FTP (File Transfer Protocol) to provide such service successfully through the NAT router. Enable PPTP Allows machines on the LAN to connect to their corporate network ALG: using the PPTP protocol. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 74: Application
Enter the ending port to open once triggered. Open Traffic Select the protocol to trigger this rule: TCP, UDP, or All Protocol. Protocol Type: Click Apply when you are done. A maximum of 8 rules can be defined. D-Link DSL-X1852E User Manual...
Page 75: Acl
Note: The default ACL for web access IP range - 0.0.0.0~0.0.0.0 (any IP address) on the LAN interface cannot be deleted or modified. Click Add when you are done or Delete to remove the selected rule. Up to 4 rules can be created. D-Link DSL-X1852E User Manual...
Page 76: Port Forwarding
Open to enable it or Close to disable it. The Status column will reflect its current enable/disable status. Up to 10 rules can be created. D-Link DSL-X1852E User Manual...
Page 77: Parental Control
If no time periods are selected, all devices in this profile will be granted Internet access. If you do not set any schedule, you will be prompted to set one when saving the policy. D-Link DSL-X1852E User Manual...
Page 78 Internet access to specified devices of the profile immediately. You can also modify or delete an existing rule by clicking Edit or Delete respectively. Up to 12 rules can be created. D-Link DSL-X1852E User Manual...
Page 79: Static Route
Specify the interface to transit the packets of this static route. Metric: The route metric is a value from 0 to 15 that indicates the cost of using this route. Click Apply when you are done. A maximum of 16 rules can be defined. D-Link DSL-X1852E User Manual...
Page 80: Dynamic Dns
Select Manual to enter your DDNS service address manually. Hostname: Enter the host name that you registered with your DDNS service provider. Username: Enter the username for your DDNS account. Password: Enter the Password for your DDNS account. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 81: Igmp
Check the box to enable the router to operate as an Internet Group Management Protocol (IGMP) for IPv4 and Multicast Listener Discovery (MLD) proxy for IPv6. Service Number: Select the interface to apply the IGMP proxy for IGMP communication. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 82: Tr069
Activate or deactivate the periodic inform function. Interval: Specify the interval in seconds for each inform packet (1-999999). The default is 43200. Authentication Select either Server or Client authentication method. Mode: Enable Certificate Enable or disable certification for authentication. Function: D-Link DSL-X1852E User Manual...
Page 83 Section 4 - Configuration File Path: Click Choose File to locate the certificate file. Then click Upload to upload the certificate file. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 84: Voip
Enter the IP or URL address of the SIP proxy server. Proxy Server Port: Enter the port used for SIP proxy. Outbound Proxy: Enter the IP or URL address of the SIP outbound proxy server. Outbound Proxy Enter the port used for SIP outbound proxy. Port: D-Link DSL-X1852E User Manual...
Page 85 Indicates the respective VoIP line for configuration. Port Enable Enable or disable the respective phone port. Setting: Registration Displays whether the line is registered successfully. Status: Account: Enter the name for your VoIP account. Password: Enter the password for your VoIP account. D-Link DSL-X1852E User Manual...
Page 86: Voip Advanced
Select the voice session refresher rule: none, uac, or uas. Rule: Session Update Select the method for updating a voice session: Update or Invite. Method: Jitter Buffer Max: Enter the maximum value for jitter buffer size. The default is 200 bytes D-Link DSL-X1852E User Manual...
Page 87 Select the mode for the codec (0~7). The default is 0. ptime setup Select the packetization time (ptime): 10, 20, or 30. Digit Map Enable: Enable or disable the digital map. If enabled, input the digit map in the text box below. D-Link DSL-X1852E User Manual...
Page 88: Sip Filter
IP addresses or domains specified in a whitelist. Click Add to add your filtering rule. After adding the rules, you can select a rule and click Delete to delete it. A maximum of 16 rules can be created. D-Link DSL-X1852E User Manual...
Page 89: Management
Select None if you don't want to specify a backup NTP server. Click Save when you are done. To configure and manage the schedule, click the Schedule tab and refer to Schedule on page 84. D-Link DSL-X1852E User Manual...
Page 90: Schedule
Delete column. If you wish to in the Edit column. If you wish to create a new schedule, edit a rule, click click the Add Rule button. A maximum of 10 schedules can be created. D-Link DSL-X1852E User Manual...
Page 91: Log Info
Refer to System Log on page 86 for information on how to enable the system logging. Note that the type of log events is determined by the log level settings in System Log. D-Link DSL-X1852E User Manual...
Page 92: System Log
Activate or deactivate logging on the system's flash of the router. Remote Enable: Activate or deactivate remote logging. If enabled, enter the remote log server below. Remote Log Enter the IP address or URL address for the Syslog server. Server: D-Link DSL-X1852E User Manual...
Page 93 Warning: Indicates that a warning message of an operational problem . Note: Indicates a normal but not stable condition. Notice: Indicates a condition that is not erroneous but requires some attention. Debug: Contains debugging messages for debugging purposes. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 94: System Settings
Click Select File to locate the Drive: configuration file from your local directory, then click Upload Settings to start uploading the configurations. Note: The router will reboot during the restoration process. Do not turn the power on or off. D-Link DSL-X1852E User Manual...
Page 95: Admin
Enter a new password for the admin account. You will need to enter this password whenever you configure the router using a web browser. Confirm Password: Confirm the administrator account password. Click Save when you are done. D-Link DSL-X1852E User Manual...
Page 96: Firmware Upgrade
Then click Upload to begin the upgrade process. Do not power off the router while the firmware is being uploaded; otherwise, errors will occur that may result in malfunction of the router and further RMA services may be required. D-Link DSL-X1852E User Manual...
Page 97: Statistics
The table at the bottom of the page displays the total number of packets and the amount of data sent and received since the DSL-X1852E started. Note: The traffic counter will reset if the device restarts.
Page 98: Diagnostics
For Traceroute Test, choose the WAN Interface through which the packets will be transferred, enter the IP address or web address in the Destination Address field, then click Start. The results of the test will be displayed in the text box below. D-Link DSL-X1852E User Manual...
Page 99: Connect And Share A Usb Storage Device
Connect and Share a USB Storage Device After you have successfully installed and configured your D-Link Router, you are ready to enjoy the benefits of D-Link’s USB sharing technology. This allows you to quickly and easily share a USB storage device with multiple computers on your network.
Page 100: Connecting From A Windows-Based Pc
Section 5 - Connect and Share a USB Device Connecting from a Windows-Based PC It is required that all of your devices are connected to the same wireless network as the DSL-X1852E. Step 1 - Press the Windows logo key + E to open File Explorer.
Page 101 PC) and Connect using different credentials. Click Finish. If you have multiple USB storage devices attached via a USB hub, click USB Device from the Home page of the DSL-X1852E’s Web Configuration utility for a list of available volume names. D-Link DSL-X1852E User Manual...
Page 102 Congratulations! Your files are now shared. The new network drive can be found in your File Explorer. You can access it without having to type its network name each time. Repeat this process from each Windows PC you wish to share your USB drive with. D-Link DSL-X1852E User Manual...
Page 103: Connect And Share With Dlna Devices
Connect and Share with DLNA Devices The DSL-X1852E can also stream media files using Digital Living Network Alliance (DLNA). With other DLNA-enabled devices, you can share photos, music, and videos stored in the USB drive with other computers and devices on your network . Connect a USB storage device to the USB Port on the DSL-X1852E first.
Page 104: Accessing From File Explorer On Windows
Accessing from File Explorer on Windows Note: It is required that all of your devices are connected to the same wireless network as the DSL-X1852E. Step 1 - Enable network discovery on Windows: Go to Control Panel > Network and Internet > Network and Sharing Center and select Change advanced sharing settings on the left.
Page 105 Step 4- Click Network to list connected network devices on your network in your File Explorer. Step 5 - Double-click your DSL-X1852E listed under Media Devices. The Windows Media Player will start automatically. You can then browse your shared media under Other Libraries and play them directly.
Page 106: Connect A Wireless Client To Your Router
WPS. Once you know, follow the steps below: Step 1 - Press the WPS button on the DSL-X1852E for about 5 seconds. The WPS LED on the front panel will start to blink.
Page 107: Windows® 11/10
WPA/WPA2/WPA3 When connecting to the DSL-X1852E wirelessly for the first time, you will need to input the wireless network name (SSID) and Wi-Fi password (security key) of the device you are connecting to. If your product has a Wi-Fi configuration card, you can find the default network name and Wi-Fi password here.
Page 108 Your computer will now automatically connect to this wireless network when it is detected. You can also use Wi-Fi Protected Setup (WPS) to connect to the router. Press the WPS button on your router and you will be automatically connected. D-Link DSL-X1852E User Manual...
Page 109: Windows® 8
Wireless Icon Clicking on this icon will display a list of wireless networks that are within connecting proximity of your computer. Select the desired network by clicking on the network name. D-Link DSL-X1852E User Manual...
Page 110 WPS button on your router during this step to enable the WPS function. When you have established a successful connection to a wireless network, the word Connected will appear next to the name of the network to which you are connected to. D-Link DSL-X1852E User Manual...
Page 111: Windows® 7
If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area. D-Link DSL-X1852E User Manual...
Page 112 It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router. D-Link DSL-X1852E User Manual...
Page 113: Troubleshooting
1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.1.1 for example), you are not connecting to a website, nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility.
Page 114 Section 7 - Troubleshooting • Access the web configuration. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your web configuration. • If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration.
Page 115 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. D-Link DSL-X1852E User Manual...
Page 116 If the Registration Status displays "Disable", "Fault", or "Unreached Network", make sure VoIP Basic settings are correctly entered and also check your internet connectivity. The VoIP settings should be supplied by your Internet telephony service provider. D-Link DSL-X1852E User Manual...
Page 117: Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products allows you to access the data you want, when, and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Page 118: What Is Wireless
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. D-Link DSL-X1852E User Manual...
Page 119 Who uses wireless? Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business, D-Link has a wireless solution for it. Home Uses/Benefits • Gives everyone at home broadband access •...
Page 120: Tips
The wireless connection in public places is usually called “hotspots”. Using a D-Link USB adapter with your laptop, you can access the hotspot to connect to the Internet from remote locations like: airports, hotels, coffee shops, libraries, restaurants, and convention centers.
Page 121: Networking Basics
Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Page 122: Statically Assign An Ip Address
(where x is a hexadecimal digit). Set Preferred DNS the same as the LAN IP address of your router. The Alternate DNS is only optional or you may enter a DNS server from your ISP. 5. When you’re done, click Save. D-Link DSL-X1852E User Manual...
Page 123: Wireless Security
Appendix B - Networking Basics Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DSL-X1852E offers the following types of security: • WPA2/WPA with 802.1x (Wi-Fi Protected Access 2) •...
Page 124: Technical Specifications
Notes: 1. The DSL-X1852E may not support all of the mandatory features, established in Wave 1 of the IEEE 802.11ax specifications. 2. Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n, 802.11ac, and 802.11ax specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.
Page 125: Regulatory Statements
Potencia máxima de Salida Frequenza/e Potenza max. Output Frequentie(s) Max. Output Power 5.15 – 5.25 GHz 200 mW 5.25 – 5.35 GHz 200 mW 5.47 – 5.725 GHz 2.4 G 2.4 – 2.4835 GHz 100 mW D-Link DSL-X1852E User Manual...
Page 126 υλικολογισμικό του προϊόντος είναι διαθέσιμα για λήψη από τη σελίδα του προϊόντος στην τοποθεσία www.dlink. com. Par les présentes, D-Link Corporation déclare que ce produit, ces accessoires et ce logiciel sont conformes aux Français [French] directives 2014/53/UE.Le texte complet de la déclaration de conformité de l'UE et le icroprogramme du produit sont disponibles au téléchargement sur la page des produits à...
Page 127 2014/53/EU. Pełen tekst deklaracji zgodności UE oraz oprogramowanie sprzętowe do produktu można pobrać na stronie produktu w witrynie www.dlink.com. Desta forma, a D-Link Corporation declara que este produto, os acessórios e o software estão em conformidade Português [Portuguese] com a diretiva 2014/53/UE. O texto completo da declaração de conformidade da UE e do firmware...
Page 128 Appendix D - Regulatory Statements Hér með lýsir D-Link Corporation því yfir að þessi vara, fylgihlutir og hugbúnaður eru í samræmi við tilskipun Íslenska [Icelandic] 2014/53/EB. Sækja má ESB-samræmisyfirlýsinguna í heild sinni og fastbúnað vörunnar af vefsíðu vörunnar á www.
Page 129 Access Points unterstützen die Funktionen DFS (Dynamic Frequency Selection) und TPC (Transmit Power Control) wie erforderlich bei Betrieb auf 5 GHz innerhalb der EU. • Bitte schlagen Sie im Handbuch oder Datenblatt nach nach, ob Ihr Gerät eine 2,4 GHz und / oder 5 GHz Verbindung nutzt. D-Link DSL-X1852E User Manual...
Page 130 5 GHz dentro de la UE. • Por favor compruebe el manual o la ficha de producto para comprobar si el producto utiliza las bandas inalámbricas de 2.4 GHz y/o la de 5 GHz. D-Link DSL-X1852E User Manual...
Page 131 Toegangspunten ondersteunen DFS (Dynamic Frequency Selection) en TPC (Transmit Power Control) functionaliteit zoals vereist bij gebruik in 5 GHz binnen de EU. • Raadpleeg de handleiding of de datasheet om te controleren of uw product gebruik maakt van 2.4 GHz en/of 5 GHz. D-Link DSL-X1852E User Manual...
Page 132 • Halten Sie das Produkt von Heizkörpern und anderen Quellen fern, die Wärme erzeugen. • Trennen Sie das Produkt immer von der Stromzufuhr, bevor Sie es reinigen und verwenden Sie dazu ausschließlich ein trockenes fusselfreies Tuch. D-Link DSL-X1852E User Manual...
Page 133 • Mantenga el producto alejado de los radiadores y de otras fuentes de calor. • Desenchufe siempre el producto de la alimentación de red antes de limpiarlo y utilice solo un paño seco sin pelusa D-Link DSL-X1852E User Manual...
Page 134 • Houd het product uit de buurt van radiators en andere warmtebronnen. • U dient het product steeds los te koppelen van de stroom voordat u het reinigt en gebruik uitsluitend een droge pluisvrije doek D-Link DSL-X1852E User Manual...
Page 135 D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging. D-Link recommends that you always switch off or unplug your D-Link products when they are not in use. By doing so you will help to save energy and reduce CO2 emissions.
Page 136 D-Link et l’environnement Chez D-Link, nous sommes conscients de l'impact de nos opérations et produits sur l'environnement et nous engageons à le réduire. Pour limiter cet impact, D-Link conçoit et fabrique ses produits de manière aussi écologique que possible, en utilisant des matériaux recyclables et faiblement toxiques, tant dans ses produits que ses emballages.
Page 137 D-Link zijn producten zo milieuvriendelijk mogelijk, door het gebruik van recycleerbare producten met lage toxiciteit in product en verpakking. D-Link raadt aan om steeds uw D-Link producten uit te schakelen of uit de stekker te halen wanneer u ze niet gebruikt. Door dit te doen bespaart u energie en beperkt u de CO2-emissies.
Page 138 D-Link a životní prostředí Ve společnosti D-Link jsme si vědomi vlivu našich provozů a výrobků na životní prostředí a snažíme se o minimalizaci těchto vlivů. Proto své výrobky navrhujeme a vyrábíme tak, aby byly co nejekologičtější, a ve výrobcích i obalech používáme recyklovatelné a nízkotoxické materiály.
Page 139 D-Link produkter som er så miljøvennlig som mulig, ved å bruke resirkulerbare, lav-toksiske materialer både i produktene og forpakningen. D-Link anbefaler at du alltid slår av eller frakobler D-Link-produkter når de ikke er i bruk. Ved å gjøre dette hjelper du å spare energi og å redusere CO2-utslipp.
Page 140 D-Link sine produkter, så de er så miljøvenlige som muligt, ved at bruge genanvendelige materialer med lavt giftighedsniveau i både produkter og emballage. D-Link anbefaler, at du altid slukker eller frakobler dine D-Link-produkter, når de ikke er i brug. Ved at gøre det bidrager du til at spare energi og reducere CO2-udledningerne.
Page 141 D-Link och miljön På D-Link förstår vi och är fast beslutna att minska den påverkan våra verksamheter och produkter kan ha på miljön. För att minska denna påverkan utformar och bygger D-Link sina produkter för att de ska vara så miljövänliga som möjligt, genom att använda återvinningsbara material med låg gifthalt i både produkter och förpackningar.

D-Link DSL-X1852E User Manual

Quick Links

Related Manuals for D-Link DSL-X1852E

Summary of Contents for D-Link DSL-X1852E

Table of Contents