Smanos GD8800 User Manual

。
sman s·

Gas Leakage Detector

GD8800
User Manual
r In叫ction
This is a high-stability combustible gas detecto「（detecto「 in abbr. ),
which is used for detecting the leakage of combustible gases. The
。
detecto「 adapts up-to-date low cu「陀nt semiconducto「 gas sensor,
with advantages of stable working, I ng service life, and easy
installation. It can detect leaking gas in time and give out ala
signal with voice warning message and strobe light. The product is
applicable to 「esidential a「eas, buildings, villas, hotels, apa「tments
and any places where the combustible gas exits.
I I
F tu s
臼
陪
High 陪liability senso
「
Strobe alarming with preset voice warning message
Auto reset
MCU P ocessing
「
Automatic testing indication fo malfunctions
「
Natural gas/ LPG induced
I
阳｜
Overv
①Malfunction LED (Yellow)
②
Normal working LED (G陪en)
@ Alarm LED (Red)
。
LED Indicati n
Red LED flashes Gas leaking
Green LED flashes Warm-up state, inn
Green LED on Wo
m
「
Yel l LED on Inner malfunction
口哨
Note:The y刨low indicator flashes and the loudspeaker plays the malfuncti o n voice
message and siren so md when the invalidity of in田rnal
bu n (or shut off the power supply, and由en power on again), the d
忱。
on self-test.
If由e main』nction LED indicator s世II keeps flashing in yellow after the abo
have done, please pσwer off the detec田r and c
I
时｜
Pair with Control P
Please pai「the detecto「with cont「'OI panel befo「E use
①
Make sure the control panel ente
the relative use manual).
「
@ Power on the detecto and then p
「
wi「eless signal, the pai「ing is successful when a beep is hea「d from
panel.
After Pai
receive alarm signal from the detector.
｜胁
＠
⑤
While the detector is powered on, it will enter self-testing state
first (the green
time and siren beeps once when testing is normal) , and then the
detector enters warm-up state ( the green indicator flashes once
pe
long time), the siren gives out a long beep, and the green
@ Built-in siren
indicator lights up constantly, which indicates the detector ente
⑤
Reset /Test button into the wo
@ Gas convection window
�
The detecto
below is happened:
r sensors operating
啤
king state
「
Press the test
button in warm-up
state
r is detected. Press由e test
随时。
will power
自由「
Press the test
operafon
。
button in working
回
ntact af回问剧团service in me.
state
甘
四川陪
The
reac
alarming dens↑句'
level
Note:
s pairing state (Please referto
alarming，汗you p
「
but the red indicator 比eeps flashing u而I the detector r矶Jms to normal working
autom
ess陆test button to send out
「
ing, the control panel will ala m immediately when
「 「
恒｜
问
b
r
I
ed yellow LED indicato s flash once at the same
／「 「
second). ln about 3 minutes (3-10 minutes if haven
「
king state
「
will send out wireless ala m signal if any condition
「 「
Voice warning
Situation

LED indication

message
冶llow and red flash once
at the same time币「st and
then o仔
油llow and red indicate「伯伯
口nee at the same time币「st ,
then the red indicator keeps
Plays twice
明ashes until the voice
message was played and the
alarming was over
fi!!
l ea k a g e
the
Red indicator keeps flashing Plays in turn
。 。
After the gas is eliminated, the detect r returns ton rmal automatically. When
s down the reset bu n, the loudspeaker stops alamning
址。
『国
cally.
剖：i
'
t use it b
「
S
「
Si
陪同
／
Sounds
10
seconds
Sounds
in turn
eminde r.
『
te
白