Related Manuals for Ihse Draco vario 474 Series
Summary of Contents for Ihse Draco vario 474 Series
- Page 1 USER MANUAL Draco vario Add-on Modules Series 474 Document 474-Add-on Modules_REV01.00_en Edition: 2022-08-19...
- Page 2 The model and serial number of your products are indicated on the bottom of our products. Always refer to this information when you need to contact your distributor or the support of IHSE GmbH (see chapter 11, page 69). Trademarks and Trade Names All trademark and trade names mentioned in this document are acknowledged to be the property of their respective owners.
-
Page 3: Table Of Contents
474-Add-on Modules Table of Contents Table of Contents Table of Contents ................................3 Important Information ............................7 Firmware and Software ..........................7 Symbols for Warnings and Helpful Information ................... 7 Terms and Spellings............................ 7 Intended Use ............................... 8 Certificates/Directives..........................9 1.5.1 North American Regulatory Compliance ................... - Page 4 Table of Contents 474-Add-on Modules 4.6.15 Add-on Module Digital Audio (unidirectional) L-/R474-BDD ............ 26 4.6.16 Add-on Module Digital Audio (unidirectional) L-/R474-BDA ............ 27 4.6.17 Add-on Module Digital Audio (unidirectional) L-/R474-BDE ............ 27 4.6.18 Add-on Module Digital Audio (unidirectional) L-/R474-BDE2 ..........27 4.6.19 Add-on Module Digital Audio (unidirectional) L-/R474-BDH ............
- Page 5 474-Add-on Modules Table of Contents Updating the Firmware of Add-on Modules, USB 2.0 Stand-alone Modules and Fan Cartridge Module . 47 8.3.1 Updating the Firmware of Add-on Modules ................47 8.3.2 Updating the Firmware of USB 2.0 Stand-alone Modules ............47 8.3.3 Updating the Firmware of the Fan Cartridge Module ..............
- Page 6 Table of Contents 474-Add-on Modules 10.5 Dimensions Add-on Modules ........................67 10.6 Weight ............................... 68 10.6.1 Add-on Modules ........................68 10.6.2 USB 2.0 Stand-alone Modules ....................68 10.6.3 Fan Cartridge Module ......................68 10.7 Environmental Conditions and Emissions ....................68 10.8 MTBF .................................
-
Page 7: Important Information
474-Add-on Modules Important Information Important Information Firmware and Software The information in this manual refers to the latest extender firmware available at the date of manual release. Please refer to the change log (see chapter 15, page 77) for user manual updates. Symbols for Warnings and Helpful Information The meaning of the symbols used for warnings and helpful information in this manual is described below: WARNING... -
Page 8: Intended Use
Important Information 474-Add-on Modules The following text formats are used for, e.g., descriptions of editing files or updating firmware: Keyboard command Description Config.txt E.g., file name #CFG E.g., file content Intended Use Add-on Modules Add-on modules are only intended for use in conjunction with extender modules and for installation in 474-BODY chassis. -
Page 9: Certificates/Directives
EU Declaration of Conformity Please find the EU Declaration of Conformity for the device under: www.ihse.com/eu-declaration-of-conformity A copy of the original, product-specific EU Declaration of Conformity can be provided upon request. For contact details, see page 2 of this manual. -
Page 10: Safety Instructions
Safety instructions 474-Add-on Modules Safety instructions To ensure reliable and safe long-term operation of your device, please note the following guidelines: Read this user manual carefully. Read the manual for the chassis in which the add-on modules are installed. Also read the extender module manual for the extender modules with which you are using the add-on module. -
Page 11: Consignes De Sécurité
474-Add-on Modules Consignes de Sécurité Consignes de Sécurité Pour garantir un fonctionnement fiable et sûr de votre périphérique à long terme, veuillez respecter les directives suivantes : Lisez attentivement ce manuel d'utilisation. Lisez le manuel d'utilisation du châssis dans lequel les modules d'extension sont installés. Les instructions, les consignes de sécurité... -
Page 12: Description
Therefore, please first select a chassis, then select one or more extender module(s), then select one or more add-on module(s) if required. The Draco System Designer, available on the IHSE website at https://dsd.ihse.com, will help you with system configuration. For more information, please refer to Described in this manual. -
Page 13: Embedded Signals
474-Add-on Modules Description An add-on module can contain up to 2 independent function parts (part A and B), one on the left and one on the right, see Fig. 1. Fig. 1 KVM Extender pair with CPU Unit and CON Unit KVM Extender pair Interconnect cable Add-on module/USB 2.0 stand-alone module (optional) - Page 14 Description 474-Add-on Modules Example with optional Add-on Module R474-BDX To output an audio signal with separate speakers, there is only the optional audio add-on module for the CON Unit required. Fig. 3 De-embedding of audio signals in a KVM extender pair (example R474-BDX) Source USB HID signal Video signal with embedded audio...
-
Page 15: Overview Add-On Modules
474-Add-on Modules Description 4.1.4 Overview Add-on Modules This section illustrates an overview of the available types of add-on modules for KVM extender modules. Fig. 4 Overview add-on modules... -
Page 16: Audio Compatibility
Description 474-Add-on Modules 4.1.5 Audio Compatibility The audio compatibility depends on the combination of extender modules and add-on modules, see following figure. HDMI 1.3: 5.1-Channel LPCM digital audio, embedded/ HDMI 2.0: 2-Channel LPCM digital audio, embedded DP 1.1: 5.1-Channel LPCM digital audio, embedded/ DP 1.2: 2-Channel LPCM digital audio, embedded 5.1-Channel PCM digital audio Balanced audio... -
Page 17: Installation Examples
474-Add-on Modules Description Installation Examples This section illustrates typical installations of KVM extender pairs. The CPU Unit is connected directly to the source using the supplied cables. The CON Unit is connected to the console. The CPU Unit and the CON Unit communicate with each other through the interconnect cables. 4.2.1 Single-Head Installation with Add-on Module Audio Fig. -
Page 18: Product Types
Description 474-Add-on Modules Product Types 4.3.1 Add-on Modules Add-on Modules USB 2.0 embedded and USB HID Part. No. Description L474-BXE Add-on module with 2x USB 2.0 embedded (up to 36 Mbit/s) R474-BXE L474-BXE2 Add-on module with 4x USB 2.0 embedded (up to 50/100 Mbit/s) R474-BXE2 L474-BXH Add-on module with 2x USB HID, Hot Key function available (R474-BXH) - Page 19 474-Add-on Modules Description Add-on Modules Analog Audio (bidirectional), RS422 (serial) Part. No. Description L474-BSX Add-on module with analog audio (bidirectional) and RS422 (serial) R474-BSX L474-BSE Add-on module with analog audio (bidirectional), RS422 (serial) and 2x USB 2.0 embedded (up to 36 Mbit/s) R474-BSE L474-BSE2 Add-on module with analog audio (bidirectional), RS422 (serial) and...
-
Page 20: Usb 2.0 Stand-Alone Modules
Description 474-Add-on Modules Part. No. Description R474-BGA Add-on module for CON Units with up to 8 configurable GPIO in-/outputs, with analog audio (bidirectional) and RS232 (serial)s R474-BGE2 Add-on module for CON Units with up to 8 configurable GPIO in-/outputs and 4x USB 2.0 embedded (up to 50/100 Mbit/s) 4.3.2 USB 2.0 Stand-alone Modules... -
Page 21: Scope Of Delivery
474-Add-on Modules Description Scope of Delivery Some add-on modules consist of 2 function parts (left and right). In the case of add-on modules with 2 function parts, more cables are supplied accordingly (e.g., 2 audio parts or 1 audio part and 1 PS/2 part). Product type Delivery scope per function part Add-on module... -
Page 22: Product View
Description 474-Add-on Modules Product View 4.6.1 Add-on Module USB 2.0 embedded L-/R474-BXE Source side (CPU module) Sink side (CON module) Fig. 8 Interface side L-/R474-BXE USB Type B, USB 2.0 (up to 36 Mbit/s) USB Type A, USB 2.0 (up to 36 Mbit/s) USB Type A, USB 2.0 (up to 36 Mbit/s) 4.6.2 Add-on Module USB 2.0 embedded L-/R474-BXE2... -
Page 23: Add-On Module Analog Audio (Bidirectional) L-/R474-Bax/-Brx
474-Add-on Modules Description 4.6.4 Add-on Module Analog Audio (bidirectional) L-/R474-BAX/-BRX Source side (CPU module) Sink side (CON module) Fig. 11 Interface side L-/R474-BAX/-BRX D-Sub 9, female socket, RS232 serial D-Sub 9, male socket, RS232 serial 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, output 3.5 mm jack socket, analog audio, output... -
Page 24: Add-On Module Analog Audio (Bidirectional) L-/R474-Bah
Description 474-Add-on Modules 4.6.7 Add-on Module Analog Audio (bidirectional) L-/R474-BAH Source side (CPU module) Sink side (CON module) Fig. 14 Interface side L-/R474-BAH D-Sub 9, female socket, RS232 serial D-Sub 9, male socket, RS232 serial 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, output 3.5 mm jack socket, analog audio, output... -
Page 25: Add-On Module Analog Audio (Bidirectional) L-/R474-Bss
474-Add-on Modules Description 4.6.10 Add-on Module Analog Audio (bidirectional) L-/R474-BSS Source side (CPU module) Sink side (CON module) Fig. 17 Interface side L-/R474-BSS D-Sub 9, female socket, RS422 serial D-Sub 9, female socket, RS422 serial 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, output 3.5 mm jack socket, analog audio, output... -
Page 26: Add-On Module Analog Audio (Bidirectional) L-/R474-Bsh
Description 474-Add-on Modules 4.6.13 Add-on Module Analog Audio (bidirectional) L-/R474-BSH Source side (CPU module) Sink side (CON module) Fig. 20 Interface side L-/R474-BSH D-Sub 9, female socket, RS422 serial D-Sub 9, female socket, RS422 serial 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, input 3.5 mm jack socket, analog audio, output 3.5 mm jack socket, analog audio, output... -
Page 27: Add-On Module Digital Audio (Unidirectional) L-/R474-Bda
474-Add-on Modules Description 4.6.16 Add-on Module Digital Audio (unidirectional) L-/R474-BDA Source side (CPU module) Sink side (CON module) Fig. 23 Interface side L-/R474-BDA RCA, S/PDIF, input RCA, S/PDIF, output Mini-XLR, AES/EBU, input Mini-XLR, AES/EBU, output TOSLINK, S/PDIF, input TOSLINK, S/PDIF, output D-Sub 9, female socket, RS232 serial D-Sub 9, male socket, RS232 serial 3.5 mm jack socket, analog audio, input... -
Page 28: Add-On Module Digital Audio (Unidirectional) L-/R474-Bdh
Description 474-Add-on Modules 4.6.19 Add-on Module Digital Audio (unidirectional) L-/R474-BDH Source side (CPU module) Sink side (CON module) Fig. 26 Interface side L-/R474-BDH RCA, S/PDIF, input RCA, S/PDIF, output Mini-XLR, AES/EBU, input Mini-XLR, AES/EBU, output TOSLINK, S/PDIF TOSLINK, S/PDIF, output USB Type B, USB HID USB Type A, USB HID device 1 USB Type A, USB HID device 2... -
Page 29: Add-On Module Balanced Audio L-/R474-Bbx
474-Add-on Modules Description 4.6.22 Add-on Module Balanced Audio L-/R474-BBX Discontinued and no longer available since 01/2022. Source side (CPU module) Sink side (CON module) Fig. 29 Interface side L-/R474-BBX Switch, phantom power 6.35 mm jack socket, analog audio, output 2 6.35 mm jack socket, analog audio, input 1 6.35 mm jack socket, analog audio, output 2 6.35 mm jack socket, analog audio, input 2... -
Page 30: Add-On Module Gpio R474-Bgx
Description 474-Add-on Modules 4.6.24 Add-on Module GPIO R474-BGX Source side (CPU module) Fig. 31 Interface side R474-BGX D-Sub 9, male socket, in-/output GPIO (for an external switching solution via dry-contact) 4.6.25 Add-on Module GPIO R474-BGA Source side (CPU module) Fig. 32 Interface side R474-BGA D-Sub 9, male socket, in-/output GPIO (for an external switching solution via dry-contact) -
Page 31: Usb 2.0 Stand-Alone Module L-/R474-Bxuc
474-Add-on Modules Description 4.6.27 USB 2.0 Stand-alone Module L-/R474-BXUC Source side (CPU module) Sink side (CON module) Fig. 34 Interface side L-/R474-BXUC Mini-USB, service interface Mini-USB, service interface Cat X, interconnection Cat X, interconnection USB Type B, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) -
Page 32: Usb 2.0 Stand-Alone Module) L-/R474-Bxus
Description 474-Add-on Modules 4.6.28 USB 2.0 Stand-alone Module) L-/R474-BXUS Source side (CPU module) Sink side (CON module) Fig. 35 Interface side L-/R474-BXUS Mini-USB, service interface Mini-USB, service interface Fiber, interconnection Fiber, interconnection USB Type B, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) USB Type A, USB 2.0 (up to 50/100 Mbit/s) -
Page 33: Status Indication
474-Add-on Modules Description Status Indication The LEDs are described here once per function part of the add-on modules. Up to two function parts can be installed per add-on module, one function part on the left and one on the right. 4.7.1 Add-on Module Digital Audio Source side (CPU module) -
Page 34: Add-On Module Balanced Audio
Description 474-Add-on Modules 4.7.2 Add-on Module Balanced Audio Add-on Module L-/R474-BB2X Source side (CPU module) Sink side (CON module) Fig. 38 Interface side add-on module balanced audio - Status LEDs L-/R474-BB2X Status LED for input 1 Status LED for output 1 Status LED for input 2 Status LED for output 2 LEDs for the Audio Signal Status... -
Page 35: Add-On Module Usb Hid
474-Add-on Modules Description 4.7.3 Add-on Module USB HID Source side (CPU module) Sink side (CON module) Fig. 40 Interface side add-on module USB HID - Status LEDs USB HID device 1 status LED USB HID device 1 status LED USB HID device 2 status LED USB HID device 2 status LED Link status LED Link status LED... -
Page 36: Add-On Module Usb 2.0 Embedded L-/R474-Bxe
Description 474-Add-on Modules Pos. LED CPU Unit LED CON Unit Description Red, fast • Link connection between add-on module and extender module, flashing and between CPU Unit and source available. • Mouse connected to USB HID port 1 or 2. Red, fast Red, fast •... -
Page 37: Add-On Modules Usb 2.0 Embedded L-/R474-Bxe2
474-Add-on Modules Description 4.7.5 Add-on Modules USB 2.0 embedded L-/R474-BXE2 Source side (CPU module) Sink side (CON module) Fig. 42 Interface side add-on module USB 2.0 – Status LEDs L-/R474-BXE2 USB 2.0 status LED USB 2.0 status LED Connect status LED Connect status LED Link status LED Link status LED... -
Page 38: Usb 2.0 Stand-Alone Modules
Description 474-Add-on Modules 4.7.6 USB 2.0 Stand-alone Modules Source side (CPU module) Sink side (CON module) Fig. 43 Interface side USB 2.0 stand-alone modules - Status LEDs Failure LED link connection Failure LED link connection Status LED link connection Status LED link connection Status LED USB 2.0 Status LED USB 2.0 The following tables show the respective Link LED states/colors (left LED 1, 3 and right LED 2, 4) of the CPU Unit... -
Page 39: Fan Cartridge Module
474-Add-on Modules Description 4.7.7 Fan Cartridge Module Fig. 44 Interface side fan cartridge module - Status LEDs Status LED Pos. 1 Description Failure, fan is not operable. Green Fan runs with reduced speed until 40 °C (with parameter set, see chapter 7.2.4, page 45) Light blue Operating condition. -
Page 40: Access Options
Access Options 474-Add-on Modules Access Options You have following options to configure and/or operate the extender module and add-on modules: Access option Description Command mode Via USB-HID interface, R474-BxH add-on modules offer the possibility to call up the command mode using a plugged-in keyboard. The command mode enables access to several functions of connected KVM devices, using additional keyboard commands if necessary. -
Page 41: Installation And Setup
474-Add-on Modules Installation and Setup Installation and Setup NOTICE Please verify that cables, interfaces, and handling of the devices comply with the requirements (see chapter 8, page 47). First-time users are recommended to set up the system in a test environment that is limited to a single room. This makes it easier to identify and solve any cabling problems, and experiment with your system more conveniently. -
Page 42: Connecting Add-On Module Ps/2
Installation and Setup 474-Add-on Modules Connecting Add-on Module PS/2 1. Connect the source to the PS/2 ports of the CPU Unit. 2. Connect the PS/2 devices to the PS/2 ports of the CON Unit. Connecting Add-on Module USB 2.0 embedded 1. -
Page 43: Fig. 46 Example - Gpio Add-On Module Set As Input Interface
474-Add-on Modules Installation and Setup Requirements to send keyboard commands to the CPU Device Matrix firmware F04.00.200717 or newer • GPIO firmware F01.03.200723 or newer • Target device L474-BXH with HIDCPU firmware V04.03 • Re-designed hardware of R474-BGX • Option 2 - Push Button Input Interface (Macros, Favorites, Keys) The DIP switch (all switches) must be set to lower position to use the GPIO module as an input interface with an external switching solution with up to eight push buttons. -
Page 44: Configuration
Configuration 474-Add-on Modules Configuration Configuration File Config.txt) Parameters are to be written to a configuration file ( Parameter for Config.txt saved and managed on Add-on modules Flash drive of extender modules. Please refer to the extender module user manual. Fan cartridge module Flash drive of the fan cartridge module. -
Page 45: Parameters For Con Extender Modules With Audio Add-On Module
474-Add-on Modules Configuration 7.2.2 Parameters for CON Extender Modules with Audio Add-on Module The following parameter can be written into the configuration file of a CON extender module if required to configure the output setting. Output Settings Parameter Function ENAAUDIO Enable RS232 or RS422 and analog audio during Video-only connections. -
Page 46: Configuring Parameters For Fan Cartridge Module
Configuration 474-Add-on Modules Configuring Parameters for Fan Cartridge Module NOTICE #CFG If the start command is missing or is written to the wrong place, or if parameters are not separated in extra lines, the parameterization will fail. For a successful parameterization, the following sequence must be strictly observed. -
Page 47: Maintenance
474-Add-on Modules Maintenance Maintenance Cleaning NOTICE Possible damage to the mechanical and electronic components The modules described in this manual as well as the accessories can be damaged by cleaning with damp or aggressive cleaning agents. If the modules are nevertheless cleaned with damp or aggressive cleaning agents and damaged in the cleaning process, the manufacturer's warranty will be voided. -
Page 48: Updating The Firmware Of The Fan Cartridge Module
Maintenance 474-Add-on Modules 8.3.3 Updating the Firmware of the Fan Cartridge Module To update the fan cartridge module, proceed as follows using the firmware file for the fan cartridge module received from the manufacturer’s technical support: 1. Connect the fan cartridge module to any source using a Mini-USB cable. The fan cartridge module opens a flash drive. -
Page 49: Troubleshooting
474-Add-on Modules Troubleshooting Troubleshooting General Failures Diagnosis Possible reason Measure Config.txt Config.txt Parameter not set or saved. Write the parameter into parameter without file and save changes. function. Start command #CFG not set. Write the start command #CFG into first Config.txt line of the file. -
Page 50: Add-On Module, Digital Audio
Troubleshooting 474-Add-on Modules Diagnosis Possible reason Measure CPU Unit: No audio connection to the audio source Connect the analog audio source No signal at audio (microphone) available. (microphone). output (microphone). Check the connection of the audio cable between the CON Unit and the analog audio source (microphone). -
Page 51: Add-On Module, Usb Hid
474-Add-on Modules Troubleshooting Add-on Module, USB HID Source side (CPU module) Sink side (CON module) Fig. 50 Interface side add-on module USB HID - Failure indication Diagnosis Possible reason Measure All LEDs are off. Power supply voltage not available. Check the power supply units. ... -
Page 52: Add-On Module, Usb 2.0 Embedded
Troubleshooting 474-Add-on Modules Add-on Module, USB 2.0 embedded Source side (CPU module) Sink side (CON module) Fig. 51 Interface side add-on module USB 2.0 embedded - Failure indication Diagnosis Possible reason Measure All LEDs are off. Power supply voltage not available. ... -
Page 53: Usb 2.0 Stand-Alone Module
474-Add-on Modules Troubleshooting USB 2.0 Stand-alone Module Source side (CPU module) Sink side (CON module) Fig. 52 Interface side USB 2.0 stand-alone modules - Failure indication Diagnosis Possible reason Measure USB 2.0 device without No USB 2.0 device connected. Check the cable to the USB 2.0 device. function. -
Page 54: Fan Cartridge Module
Troubleshooting 474-Add-on Modules Fan Cartridge Module Fig. 53 Interface side fan cartridge module - Failure indication Diagnosis Possible reason Measure LED 1 lights up red. Fan is not operable. Check the firmware version. The fan is defect. Contact your distributor if necessary. -
Page 55: Technical Data
474-Add-on Modules Technical Data Technical Data 10.1 Interfaces 10.1.1 Mini-USB The Mini-USB interface enables a customer specified communication with some add-on modules. The firmware could also be updated using this interface. 10.1.2 USB HID Our devices with USB HID interface support a maximum of two devices with USB HID protocol. Each USB HID port provides a maximum current of 100 mA. -
Page 56: Usb 2.0 (Transparent)
Technical Data 474-Add-on Modules 10.1.4 USB 2.0 (transparent) The extender module with transparent USB 2.0 interface supports almost all types of USB 2.0 devices. USB 2.0 data transfer is supported with USB high speed (max. 480 Mbit/s) or USB-embedded (up to 36/50/100 Mbit/s), depending on the add-on module. -
Page 57: Rs422 Serial
474-Add-on Modules Technical Data Parameter Value Connection Format DTE (Data Terminal Equipment) Speed • Up to 19,200 Bd (L- /R474-BAx) • Up to 115,200 Bd (L-/R474-BRx) Data Format Format independent Data Transmission • RxD (Receive Data) • TxD (Transmit Data) Traffic Control The following signals are transmitted (hardware handshake): •... -
Page 58: Analog Audio
Technical Data 474-Add-on Modules 10.1.8 Analog Audio Extender modules with the analog audio option support a bidirectional stereo audio transmission, in near-CD quality. audio interface is a 'line level' interface, and it is designed to transmit the signals of a sound card (or another 'line level' device) as well as to allow the connection of active speakers to the CON Unit. -
Page 59: Digital Audio
474-Add-on Modules Technical Data 10.1.9 Digital Audio Extender modules with the digital audio option support the unidirectional transmission of digital audio data. Up to three sources can be connected to the CPU Unit. The active source is transmitted. If several sources are active, the XLR signal takes priority, otherwise the first active signal. -
Page 60: Balanced Audio
Technical Data 474-Add-on Modules 10.1.10 Balanced Audio Extender modules with a balanced audio interface support a unidirectional 2-channel mono or 1-channel stereo transmission in studio quality. The audio interface is at the same time a 'Line-Level' and 'Mic-Level' interface and is designed to transmit signals of a microphone or mixing desk for example with a high tolerance for interferences, even at larger distances. - Page 61 474-Add-on Modules Technical Data Configuration of the Sample Rate The sample rate of the balanced audio interface can be configured individually. The default sample rate is 48.0 kHz. • Config.txt The sample rate can be configured in the file of the extender module with the balanced audio CPU •...
-
Page 62: Interconnect Cables
Technical Data 474-Add-on Modules 10.2 Interconnect Cables 10.2.1 Cat X NOTICE Transmission problems Routing over an active network component, such as an ethernet hub, switch, or router is not allowed. Operation with several patch fields is possible. Establish a point-to-point connection. ... -
Page 63: Fiber
474-Add-on Modules Technical Data 10.2.2 Fiber NOTICE Transmission problems Routing over an active network component, such as an ethernet hub, switch, or router is not allowed. Operation with several patch fields is possible. Establish a point-to-point connection. Type of Interconnect Cable* Type of cable Specification Single-mode 9 μm... -
Page 64: Connector Pinouts
Technical Data 474-Add-on Modules 10.3 Connector Pinouts 10.3.1 USB, Type A Connector Signal Color +5 V (DC) Data - White Data + Green Black 10.3.2 Mini-USB, Type B Connector Signal Color +5 V (DC) Data - White Data + Green Not connected Black 10.3.3 PS/2... -
Page 65: D-Sub 9 (Serial Rs422), Cpu Modules
474-Add-on Modules Technical Data 10.3.6 D-Sub 9 (Serial RS422), CPU Modules Connector Signal Signal Rx-GND Rx(A)- (in) Rx(B)+ (in) Tx(B)+ (out) Tx(A)- (out) Tx-GND Not connected 10.3.7 D-Sub 9 (Serial RS422), CON Modules Connector Signal Signal Tx-GND Tx(A)- (out) Tx(B)+ (out) Rx(B)+ (in) Rx(A)- (in) Rx-GND... -
Page 66: Phoenix Terminal Block, 6-Pole, Cpu Modules
Technical Data 474-Add-on Modules 10.3.10 Phoenix Terminal Block, 6-pole, CPU Modules Connector Signal IN 1, + IN 1, - IN 1, GND IN 2, + IN 2, - IN 2, GND 10.3.11 Phoenix Terminal Block, 6-pole, CON Modules Connector Signal OUT 1, + OUT 1, - OUT 1, GND... -
Page 67: Current Draw And Power Consumption (Per Function Part)
474-Add-on Modules Technical Data 10.4 Current Draw and Power Consumption (per Function Part) NOTICE Exceeding the maximum permissible current consumption In addition to the current consumption of the extender and additional modules, there is also the current consumption by the connected periphery. ... -
Page 68: Weight
Technical Data 474-Add-on Modules 10.6 Weight 10.6.1 Add-on Modules Product type Max. weight L474- Max. weight R474- 70 g 70 g BAH/BSH/BDX 75 g 75 g BXH/BAX/BRX/BSX 85 g 85 g BXE/BXE2/BDE2 90 g 90 g BDE/BDD/BBX/BB2X 95 g 95 g BAP/BRE/BSE/BDA 100 g 100 g... -
Page 69: Technical Support
474-Add-on Modules Technical Support Technical Support Prior to contacting support, please ensure you have read this manual, and then installed and set-up your KVM extender as recommended. 11.1 Support Checklist To efficiently handle your request, it is necessary that you complete a support request checklist (Download). Please ensure that you have the following information available before you call: •... -
Page 70: Glossary
Glossary 474-Add-on Modules Glossary The following terms are commonly used in this manual or in video and KVM technology. Term Description AES/EBU Interface specification for the transmission of digital stereo, two-channel, or mono audio signals between different devices according to the AES3 standard. Cat X Any Cat 5e (Cat 6, Cat 7) cable. - Page 71 474-Add-on Modules Glossary Term Description Single-Mode 9 µm single-mode fiber cable. TOSLINK Standardized fiber connection system for digital transmission of audio signals (F05 plug connection). USB HID USB HID devices (Human Interface Device) allow users to interact with computers. There is no need for a special driver during installation.
-
Page 72: Index
Index 474-Add-on Modules Index USB HID ..............55 Access Options ............40 Accessories ............... 20 LEDs Add-on Modules Certificates ..............9 Balanced Audio ..........34 Configuration Digital Audio ............33 Configuration File ..........44 USB 2.0 embedded L-/R474-BXE ....36 Fan Cartridge Module ........... - Page 73 474-Add-on Modules Index RCA (Cinch) ............66 L-/R474-BDH ..........28 Stereo Jack Plug ..........65 L-/R474-BDX ..........26 Toslink ..............66 GPIO USB, Type A ............64 R474-BGA ............ 30 Product Types ............18 R474-BGE2 ..........30 Add-on Modules R474-BGX ............ 30 Analog Audio USB 2.0 embedded RS232 (serial) ..........
- Page 74 Index 474-Add-on Modules Digital Audio ............. 59 GPIO ..............56 Mini-USB ............55 PS/2 ..............55 RS232 Serial ............ 56 RS422 Serial ............ 57 USB 2.0 (transparent) ........56 USB HID ............55 MTBF ..............68 Power Consumption ..........67 Weight ..............
-
Page 75: Table Of Figures
474-Add-on Modules Table of Figures Table of Figures Fig. 1 KVM Extender pair with CPU Unit and CON Unit ..................13 Fig. 2 Embedding/de-embedding of signals in a KVM extender pair (example L- /R474-BAE) ......13 Fig. 3 De-embedding of audio signals in a KVM extender pair (example R474-BDX) .......... 14 Fig. - Page 76 Table of Figures 474-Add-on Modules Fig. 43 Interface side USB 2.0 stand-alone modules - Status LEDs ............... 38 Fig. 44 Interface side fan cartridge module - Status LEDs ..................39 Fig. 45 Example - GPIO add-on module set as output interface................42 Fig.
-
Page 77: Change Log
474-Add-on Modules Change Log Change Log This table offers an overview about the most important changes available, such as new functions, changed configuration or operation. Edition Date Chapter New functions/changes REV01.00 2022-08-19 Initial user manual for 474 add-on modules.
Need help?
Do you have a question about the Draco vario 474 Series and is the answer not in the manual?
Questions and answers