Subscribe to Our Youtube Channel
Related Manuals for Scania Fleet Analysis System 2
Summary of Contents for Scania Fleet Analysis System 2
- Page 1 19:03-15 Issue 1 Fleet Analysis System 2 Retrofitting and troubleshooting ã Scania CV AB 2002, Sweden 1 713 418...
-
Page 2: Table Of Contents
Routing the aerial wiring .......... 9 Fitting GPS/GSM module ........10 Routing the FAS wiring.......... 11 Installing speaker and microphone ......14 Function test ............15 Finishing operations ................15 Troubleshooting ................16 ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 3: Function
General General The Fleet Analysis System 2, FAS 2, is supplied complete with cradle and hand-held computer. It may be easier to carry out some procedures with two people. These instructions describe retrofitting in a left- hand drive vehicle. Function... -
Page 4: Component Parts
General Component parts FAS 2 comprises: ã 19:03-15 Scania CV AB 2002, Sweden... - Page 5 20 Radio speaker cable C493/E33 21 Radio speaker connector 22 Microphone U9 23 Speaker 24 Plastic holder for A3D 25 A3D GPS/GSM module E55 26 VPS cable C267 27 Fuses F11, F12 28 Spring-loaded switch S86 ã 19:03-15 Scania CV AB 2002, Sweden...
-
Page 6: Connection Diagram
General Connection diagram ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 7: Sim Card
Refer to the description in 18:01-05 Cab, Interior. 3 Loosen the headlining. 4 Loosen the roof shelf on cabs with low roof. This will give access for screwing on the aerial retaining nut. ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 8: Attaching The Aerial
1 Make a 19 millimetre diameter hole with a suitable tool. Refer to the illustration for its location in relation to the roof hatch. Finely adjust the position as necessary depending on other equipment located on the roof. ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 9: Routing The Aerial Wiring
3 Run the cables via the headlining panels towards the windscreen and down behind the right-hand roof shelf lid. Then pull out the cables through the hole in the headlining to where the GPS/GSM module is being fitted. ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 10: Fitting Gps/Gsm Module
Fit the bolt from underneath and the nut from above. 5 Place the GPS/GPM module into the plastic bracket. 6 Connect the aerial cables to the GPS/GSM module. ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 11: Routing The Fas Wiring
D and connect to the central electric unit. 9 Connect the wiring to the hand-held computer cradle and the switch. Note: Connector C461 is an additional CAN socket and is not connected. ã 19:03-15 Scania CV AB 2002, Sweden... - Page 12 If the cable The alarm from the GPS/GSM module goes has been run via the GPS/GSM module in to the Scania Fleet Management Portal connection with commissioning. (FMP) and indicates the activated alarm, time and vehicle position.
- Page 13 E) Connect the mute box connector C492 to the FAS wiring. 19 For vehicles without radio or mute box: Do not use the mute box. Install the speaker as follows instead. ã 19:03-15 Scania CV AB 2002, Sweden...
-
Page 14: Installing Speaker And Microphone
8 Fit the microphone and speaker brackets at the same time as the radio panel is screwed on, see illustration. 9 Press the microphone into its bracket. 10 Fit the speaker into its bracket. ã 19:03-15 Scania CV AB 2002, Sweden... -
Page 15: Function Test
Settings, VDC settings. Check that there is contact between the hand- held computer and vehicle. Finishing operations Refit and screw on all equipment that has been removed such as panels, roof hatch, bed, ladder, etc. ã 19:03-15 Scania CV AB 2002, Sweden... - Page 16 Troubleshooting ã 19:03-15 Scania CV AB 2002, Sweden...
- Page 17 Troubleshooting ã 19:03-15 Scania CV AB 2002, Sweden...
- Page 18 Troubleshooting ã 19:03-15 Scania CV AB 2002, Sweden...
- Page 19 Troubleshooting ã 19:03-15 Scania CV AB 2002, Sweden...
- Page 20 ã Scania CV AB 2002, Sweden 19:03-15...
Need help?
Do you have a question about the Fleet Analysis System 2 and is the answer not in the manual?
Questions and answers