Atwood hydro flame 8900-III Series Technical Installation Manual

Atwood hydro flame 8900-III Series Technical Installation Manual

Hide thumbs Also See for hydro flame 8900-III Series:
Table of Contents

Advertisement

Available languages

Available languages

ENGLISH, FRANCAIS
THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE
TECHNICIAN TO INSTALL AN ATWOOD
:
TO THE INSTALLER
THESE INSTRUCTIONS MUST BE SUPPLIED WITH THE FURNACE TO THE CON
.
SUMER
PLEASE RETAIN THESE INSTRUCTIONS FOR FURTHER REFERENCE
This furnace design has been certified for installation in recre-
ation vehicles as a MSP Category III furnace. Follow this installa-
tion instruction to insure safe operation of the furnace. Failure to
install furnace according to this installation instruction nullifies
the furnace warranty.
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
WARNING
avoid possible
injury or death
FIRE OR EXPLOSION
• If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
FOR YOUR SAFETY
FIRE OR EXPLOSION
WHAT TO DO
IF YOU SMELL GAS
• Evacuate
persons from vehicle.
ALL
• Shut off gas supply at gas container or source.
touch any electrical switch, or use any phone or
DO NOT
radio in vehicle.
start vehicle's engine or electric generator.
DO NOT
• Contact nearest gas supplier or qualified Service Technician
for repairs.
• If you cannot reach a gas supplier or qualified Service
Technician, contact the nearest fire department.
turn on gas supply until gas leak(s) has been repaired.
DO NOT
Installation and service must be performed by a qualified
Service Technician, Service Center or gas supplier.
(et Canada)
- hydro flame
TM
FURNACE
CAUTION
avoid possible
injury and/or property damage
WARNING
WARNING
.
FURNACE SPECIFICATIONS
DIMENSIONS
........................................................................1
WEIGHT
-
MINIMUM CLEARANCE TO FLOORBOARDS
.
&
SIMILAR COMBUSTIBLE BUILDING MATERIALS
SAFETY INFORMATION
FURNACE INSTALLATION
........................................................................
WALL CUTOUT
..................................................................................
DUCTING
Flexible Ducting
........................................................................
Hard Ducting
OPTIONAL INSTALLATION
........................................................................
GAS CONNECTION
ELECTRICAL CONNECTIONS
Conductor Sizing Table
12 volt DC Models
120 volt AC Models
..........................................................................
Thermostat
DOOR INSTALLATION
RAIN SHIELD INSTALLATION
DRAFT CAP ASSEMBLY
CONVERTIBLE GAS CONTROL
Valve Conversion
Orifice Replacement
SYSTEM CHECK TESTS
PROPANE GAS PRESSURE
........................................................................
STATIC PRESSURE
&
AC
DC WIRING DIAGRAMS
............................................................................
ILLUSTRATIONS
REPLACEMENT PARTS LIST
SPECIFICATIONS
#
MODEL
BTU Input
Output BTU/HR
Type Gas
Duct Static Pressure -
Power Supply (
)
VOLTS
Watts
Amperage
MINIMUM RETURN AIR
DIMENSIONS
ALL MODELS WITH DOOR
Casing
Door
Recess Bezel
1
LITERATURE NUMBER
hydro flame
8900-III Series Furnace
MODELS
Technical Installation Manual
INDEX
..............................................................1
..................................................................1
,
,
WALLS
..................................
..................................................................
..................................................................
......................................................................
..................................
-
BOTTOM DISCHARGE KIT
..........................................................
............................................................
................................................................
................................................................
....................................................................
............................................................
..................................................................
........................................................
....................................................................
................................................................
....................................................................
..............................................................
............................................................
..............................................
&
DRAWING
8935
8940
-
-
DCLP
III
DCLP
III
35,000
40,000
27,300
31,200
LP
LP
.10˝ W.C.*
.10˝ W.C.
12-DC
12-DC
132
132
11
11
80 in
2
80 in
2
WIDTH
HEIGHT
DEPTH
16-1/2˝
9-1/8˝
23-1/2˝
19-1/4˝
9-1/4˝
1/4˝
20-9/16˝
11-1/2˝
MPD 34473
TM
8935, 8940
•Installation
Effective 4/1/03
2
1-2
2
-
2
3
3
3
3
3
3
3-4
3
3-4
4
4
4
4
4
4-5
4
5
5
5
5
5
6
7
*
(W.C. = Water Column)
8935
8940
-
-
ACLC
III
ACLC
III
35,000
40,000
27,300
31,200
LP/NAT
LP/NAT
.10˝ W.C.
.10˝ W.C.
120-AC
120-AC
360
360
3
3
80 in
2
80 in
2
WEIGHT
38 lbs.
FURNACE
45 lbs.
SHIPPING

Advertisement

Table of Contents
loading

Summary of Contents for Atwood hydro flame 8900-III Series

  • Page 1 Technical Installation Manual ENGLISH, FRANCAIS •Installation (et Canada) Effective 4/1/03 INDEX THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE - hydro flame TECHNICIAN TO INSTALL AN ATWOOD FURNACE ..............1 FURNACE SPECIFICATIONS ..............1 DIMENSIONS TO THE INSTALLER ................1 WEIGHT...
  • Page 2: Warning Carbon Monoxide Poisoning

    MINIMUM CLEARANCE TO USA AND CANADA FOLLOW ALL APPLICABLE STATE AND LOCAL CODES FLOORBOARDS, WALLS & SIMILAR COMBUSTIBLE BUILDING MATERIALS* IN THE ABSENCE OF LOCAL CODES OR REGULATIONS REFER TO CURRENT STANDARDS OF Recreation Vehicles ANSI A119.2/NFPA 501C. MUST BE PROVIDED THE FULL LENGTH AND WIDTH OF UNIT •...
  • Page 3 4. Position gasket (4-F) on plenum plate. CAUTION 5. Set furnace on gasket, gasket must remains in position. Use additional ducting to maintain correct static pressure. PERSONAL INJURY allow furnace tabs to protrude through side wall cutout DO NOT • GAS CONNECTION opening during installation process until door is installed and tabs 1.
  • Page 4 10-D. The draft cap assembly must be pulled out tight against door screen 10-B. Open door 10-A and tighten wing nut 10-C. POWER SUPPLY Atwood Mobile Products highly recommends the use of an electronic CONVERTIBLE GAS CONTROL FIG 5 (solid state) converter with clean, clear power output.
  • Page 5: System Checks

    PROPANE GAS PRESSURE TEST ORIFICE REPLACEMENT 1. Remove rain shield by tilting as depicted in 9 insert. The furnace and any individual shut-off valve must be disconnected 2. Remove burner assembly from control box. from gas supply piping system during any pressure testing of system 3.
  • Page 6 Access to Static Pressure Tap French Canadian words 1-1/4" 1-1/4" I D E...
  • Page 7 hydro flame 8900-III Series Furnace Models 8935, 8940 Electronic Ignition Board AC Kit Soupape CA DRAWING DESCRIPTION OF PARTS Transformer Assembly AC Moteur CC Relay Motor AC Interrupteur à abattant Thermostat - specify color High Voltage Wire Capuchon de refoulement CC/CA35 Duct Cover Plate Deluxe Door &...
  • Page 8: Pour Votre Sécurité

    UTILISÉ PAR UN TECHNICIEN DE MAINTENANCE AGRÉÉ LORS DE ....8 L'INSTALLATION D'UN APPAREIL DE CHAUFFAGE À AIR CHAUD APPAREIL DE CHAUFFAGE À AIR CHAUD CARACTÉRISTIQUES hydro flame ATWOOD......8 DIMENSIONS À L’INSTALLATEUR : ........8 ’ CES INSRUCTIONS DOIVENT ETRE FOURNIES A L...
  • Page 9: Avertissements Importants Concer- Nant L'installation

    DÉGAGEMENT MINIMUM ENTRE L'APPAREIL ÉTATS UNIS ET CANADA RESPECTEZ TOUS LES CODES LOCAUX ET TOUS LES CODES D ÉTAT EN VIGUEUR ET LE PLANCHER, LES PAROIS ET LES MATÉRIAUX DE CONSTRUCTION COM- EN L ABSENCE DE CODES LOCAUX OU DE RÉGLEMENTATIONS LOCALES REPORTEZ VOUS AUX BUSTIBLES SIMILAIRES* NORMES EN VIGUEUR SUIVANTES...
  • Page 10: Dommages Matériels

    3. Fixez la plaque de répartition d'air (4-E) sur l'emplacement découpé dans le ATTENTION plancher. Si vous n'utilisez pas de joint d'étanchéité et de plaque de réparti- tion d'air, branchez les conduits rigides à l'appareil de chauffage en vous BLESSURES CORPORELLES assurant que le joint est hermétique.
  • Page 11 • Ajustez correctement le capuchon de refoulement pour empêcher l'oxyde de ALIMENTATION ÉLECTRIQUE carbone d'entrer dans le véhicule. Atwood Mobile Products highly recommande vivement l'utilisation d'un conver- Sans serrer l’écrou à ailettes 10-C sur le capuchon de refoulement, fermez la tisseur électronique à semi-conducteurs pour éviter toute variation de tension.
  • Page 12 TEST DE PRESSION DU PROPANE REMPLACEMENT DE LA LUMIÈRE 1. Retirez l'écran de protection contre les intempéries, L'appareil de chauffage et tout robinet individuel doivent être isolés de la tuyauterie 2. Retirez le brûleur du boîtier de commande. de l'alimentation en gaz pendant les tests de pression du système à des pressions 3.

This manual is also suitable for:

Hydro flame 8935 dclp-iiiHydro flame 8940 dclp-iiiHydro flame 8935 aclc-iiiHydro flame 8940 aclc-iii

Table of Contents