Advertisement
Quick Links
ENGLISH, FRANCAIS
THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE
TECHNICIAN TO INSTALL AN ATWOOD
:
TO THE INSTALLER
THESE INSTRUCTIONS MUST BE SUPPLIED WITH THE FUR
NACE TO THE CONSUMER
:
TO THE CONSUMER
PLEASE RETAIN THESE INSTRUCTIONS FOR FURTHER REFER
.
ENCE
This furnace design has been certified for installation in recre-
ation vehicles as a MSP Category III furnace. Follow this installa-
tion instruction to insure safe operation of the furnace. Failure to
install furnace according to this installation instruction nullifies
the furnace warranty.
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
WARNING
avoid possible
injury or death
FIRE OR EXPLOSION
• If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
FOR YOUR SAFETY
FIRE OR EXPLOSION
WHAT TO DO
IF YOU SMELL GAS
• Evacuate
persons from vehicle.
ALL
• Shut off gas supply at gas container or source.
•
touch any electrical switch, or use any phone or
DO NOT
radio in vehicle.
•
start vehicle's engine or electric generator.
DO NOT
• Contact nearest gas supplier or qualified Service Technician
for repairs.
• If you cannot reach a gas supplier or qualified Service
Technician, contact the nearest fire department.
•
turn on gas supply until gas leak(s) has been repaired.
DO NOT
Installation and service must be performed by a qualified
Service Technician, Service Center or gas supplier.
9
(et Canada)
- hydro flame
FURNACE
TM
.
CAUTION
avoid possible
injury and/or property damage
WARNING
WARNING
.
FURNACE SPECIFICATIONS
-
DIMENSIONS
........................................................................
WEIGHT
-
MINIMUM CLEARANCE TO FLOORBOARDS
&
SIMILAR COMBUSTIBLE BUILDING MATERIALS
SAFETY INFORMATION
FURNACE INSTALLATION
..........................................................................
WALL CUTOUTS
................................................................................
DUCTING
Required Minimum Discharge Chart
Flexible Ducting
........................................................................
Floor Ducting
OPTIONAL INSTALLATION
OPTIONAL INSTALLATION
OPTIONAL INSTALLATION
PROPANE GAS CONNECTION
ELECTRICAL CONNECTIONS
Conductor Sizing Table
Thermostat Installation
DOOR INSTALLATION
Horizontal and Vertical Door Option
Recess Bezel Door Option
DRAFT CAP ASSEMBLY
OPTIONAL FURNACE INSTALLATION
SYSTEM CHECK TESTS
PROPANE GAS PRESSURE
........................................................................
STATIC PRESSURE
DC WIRING DIAGRAM
............................................................................
ILLUSTRATIONS
REPLACEMENT PARTS LIST
SPECIFICATIONS
#
MODEL
BTU Input
Duct Static Pressure
12 Volt Amperage (AMPS)
Watts
Power Supply (
VOLT DC
Recommended Return Air
MINIMUM RETURN AIR
DIMENSIONS
ALL MODELS
Casing
Door
Recess Bezel
1
LITERATURE NUMBER
hydro flame
8500-IV Series Furnace
8516, 8520, 8525,
MODELS
Technical Installation Manual
•Installation •Maintenance
INDEX
..............................................................
..................................................................
,
,
WALLS
..................................
..................................................................
..................................................................
............................................
......................................................................
..................................
-
BOTTOM DISCHARGE KIT
......................................
-
EXTENSION BOX KIT
........................................
-
FLEX ADAPTER KIT
............................................................
..............................................................
............................................................
............................................................
....................................................................
............................................
........................................................
..................................................................
-
Recessed Furnace
....................................................................
..............................................................
......................................................................
..............................................
&
DRAWING
8516-IV
8520-IV
8525-IV
16,000
20,000
25,000
.20˝ W.C.* .10˝ W.C.* .10˝ W.C.* .10˝ W.C.* .10˝ W.C.*
4.6
4.6
7.6
55
55
91
)
12
12
12
80 in
2
80 in
2
80 in
65 in
2
65 in
2
65 in
WIDTH
HEIGHT
DEPTH
16-1/2˝
7-3/8˝
18˝
19-1/4˝
9-1/4˝
1/4˝
20-9/16˝
11-1/2˝
MPD 33179
TM
8531, 8535
Effective 1/08
1
1
1
2
1-2
2
2
2-3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
........................
4-5
5
5
5
5
6
7
(W.C. = Water Column)
8531-IV
8535-IV
30,000
34,000
7.6
9.8
91
118
12
12
2
80 in
2
80 in
2
2
65 in
2
65 in
2
WEIGHT
30 lbs
FURNACE
32 lbs
SHIPPING
Advertisement
Related Manuals for Atwood 8516
Summary of Contents for Atwood 8516
-
Page 1: For Your Safety
•Installation •Maintenance (et Canada) Effective 1/08 THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE INDEX - hydro flame TECHNICIAN TO INSTALL AN ATWOOD FURNACE .............. FURNACE SPECIFICATIONS TO THE INSTALLER THESE INSTRUCTIONS MUST BE SUPPLIED WITH THE FUR .............. -
Page 2: Carbon Monoxide Poisoning
MINIMUM CLEARANCE TO : The direct high voltage spark ignition generates a radio frequency NOTE FLOORBOARDS, WALLS & SIMILAR COMBUSTIBLE BUILDING MATERIALS* that could cause interference with other microprocessor based MUST BE PROVIDED THE FULL LENGTH AND WIDTH OF UNIT equipment. -
Page 3: Property Damage
STATIC PRESSURE TEST 5. Position gasket on plenum plate. MODELS REQUIRED DISCHARGE 8516-IV, 8520-IV ............24in 6. Set furnace on gasket, make sure gasket remains in position. 8525-IV & 8531-IV ............36in 7. Fasten extension box to floor with two 1/2˝ sheet metal screws. -
Page 4: Warning Carbon Monoxide Poisoning
POWER SUPPLY 5. Bend tabs over and secure with six screws. Fill tab slots with RTV Atwood Mobile Products highly recommends the use of an electronic type sealant after installing furnace. (solid state) converter with clean, clear power output. This will assure... -
Page 5: System Checks
The addendum is avail- CUTOUT able from your Atwood Field Service Representative or by calling 1-1/2˝ - 2-1/2˝ RECOMMENDED WALL THICKNESS Atwood Service Toll Free. - Page 6 Access to Static Port (Accès à l’orifice statique) Vertical Installation (Installation 1-1/4" Verticale) 1-1/4" AVANT DU VEHICULE ( E X R I E I D E H I C VERTICAL FOOT PRINT...
- Page 7 8500-IV Series Furnace Models 8516, 8520, 8525, 8531, 8535 Cut Out & Cover Plate on Full Side Discharge ONLY Adaptateurs de conduit DRAWING DESCRIPTION DRAWING DESCRIPTION Blower Wheel Venturi Couvercle d'ouverture de branchement Motor Clamp Blower Housing Back de conduit Gasket/Plenum Plate Kit- Top &...