Anthro TECHNOLOGY FURNITUR SEC24 Series Assembly Instructions

Step 8
Place the Metal Base Assembly onto the legs. Check the
orientation of the Base Assembly. Casters with the Green
Brake Pedals should face either the left or the right. Also,
the slots on the metal base
(used for installing the Back Panel)
should align with the Panel Hangers on the wood shelf.
Align Vertical Legs with corner holes in the Base Assembly.
Insert a Funnel Head Screw through the Base and carefully
thread into the Leg.
Repeat for other three corners and tighten all screws.
Funnel Head Screw
325-5245-00
Step 9
Rotate your Cart upright.
Facing the rear of the Cart, orient the Back Panel so the
tabs are towards the bottom.
Carefully insert the two small tabs at the bottom of the
Back Panel into the slots on the Metal base. Tilt the top of
the Back Panel towards the Cart to meet the Panel Hang-
ers. Secure using two Panel Screws.
Panel Screw
325-5196-00
Step 10
Orient the Door so that the Lock Assembly is at the top.
With the Door in the open position , align the
(as shown)
pins on the Door Hinges with the Hinges on the Cart
and slide down into place.
Step 11
Pop the 1.5" End Caps into the tops of the Legs.
Congratulations! Your assembly is complete.
Questions?
(Green.Brake.Pedal)
Base.Assembly
Funnel.Head.
Screw
Panel.Screw
Back.Panel
Tabs
Back.Panel
Mount.Detail
Hinge.Attachment.
Detail
Door
Lock.Assembly
1.5".End.Cap
1-800-325-3841
Security Cart 24" Wide
Assembly Instructions
These Assembly Instructions
01
are for the SEC24xx/xx.
Before.beginning.assembly.of.your.
Security.Cart, . please.take.a.moment.to.
review.the.parts.listed.below.to.verify.
that.your.shipment.is.complete.
It.may.also.be.helpful.to.review.
the.Assembly.Instructions.of.all.
Anthro.Products.you.purchased.
and.are.planning.to.include.in..
this.installation.....
To.make.the.assembly.of.your.Security.
Cart . even.easier, . we.have.included.all.of.
the.required.tools. . The.handy.Hex.Driver.
Bit.can.be.used.in.your.electric.drill.in.
place.of.the.Hex.Driver. . .
.......
Hex Driver 5/32"
375-5000-00
3-Way Wrench ...........
225-5196-00
Hex Key 3/16" ............
375-5028-00
NOTE: . .When.using.a.power.drill..
during.assembly, . ALWAYS.begin..
threading.fasteners.by.hand!
Enclosed Parts List
Detailed.views.of.all.Hardware.is.provided.with.each.Assembly.Step.
01– Shelf Clamp . . .................................. Qty. . 4..........................175-5059-00
02– Shelf Support ........................
Qty. . 4..........................175-5060-00
03– Clamp Screw ..............................
Qty. . 4................... 325-5086-00
04– Door ............................................ Qty. . 1................... 835-5040-00
05– 30" Vertical Legs ...................
Qty. . 4..........................125-5267-00
06– 1.5" End Cap ..............................
Qty. . 4..........................175-5020-00
07– Side Panel X .........................
Qty. . 1.. . .......................225-5948-00
08– 24" Wide Shelf .........................
Qty. . 1..........................100-6512-00.
09– Panel Hanger .......................
Qty. . 2..........................225-5950-00
10– Panel Screw ................................
Qty. . 4..........................325-5196-00
11– Back Panel ................................... Qty. . 1..........................225-5941-00
12– Cap Screw ..................................
Qty. . 32. . ......................325-5188-00
13– 5" Rhombus Casters . . ................
......................................... (see.below)
. Swivel Lock Caster ................... Qty. . 2..........................150-5080-00
Total Lock Caster .....................
. Qty. . 2..........................150-5081-00
Anthro Corporation Technology Furniture
®
June 2006 Rev C SAVE.THESE.INSTRUCTIONS!
TECHNOLOGY FURNITURE
®
02
06
03
07
09
05
04 08
20
19
21
18
14
17
16
15
14– Lock Nut ..................................... Qty. . 16. . ......................325-5263-00
15– Caster Mount Bracket ...........
Qty. . 4.. . ..........225-0585-04-02-00
16– 3/4" Wood Screw .....................
Qty. . 12. . ......................325-5106-00
17– Funnel Head Screw ................... Qty. . 4..........................325-5245-00
18– Corner Bumper .........................
Qty. . 4..........................175-5112-00
19– Support Screw ...........................
Qty. . 12. . ......................325-5010-00
20– Side Panel Y ..........................
Qty. . 1..........................225-5949-00
21– Metal Base ...........................
Qty. . 1..........................225-5943-00
All.Screw.quantities.listed.here.are.the.minimum.needed.
for.your.Cart.assembly...There.may.be.a.few.extra.Screws.
included,.which.are.not.counted.in.the.Parts.List.
10450 SW Manhasset Drive Tualatin, Oregon 97062
®
10
11
12
13
1-800-325-3841