Step 7
Carefully, rotate the Shelf Assembly (from Step 5),
upside down as shown.
Place the Base Tube Assembly (from Step 6) onto the
Vertical Legs of the Shelf Assembly.
Attach the Base Tube to each Leg using a total of four
Base Tube Screws.
Tighten all Support, Caster, and Base Tube Screws.
Base Tube Screw
325-5000-00
Step 8
Rotate your PrinterCart over onto the Casters.
Pop the 1.5" Small End Caps into the Vertical Legs and
the 1.75" Large End Caps into the Base Tube.
Congratulations! Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
*300-5386-00*
Questions?
1.5" Small End Cap
1.75" Large End Cap
300-5386-00
1-800-325-3841
Anthro PrinterCart
Assembly Instructions
Hello! Thank you for choosing Anthro.
Before beginning assembly of your Anthro
PrinterCart, please take a moment to
review the parts listed below to verify
that your shipment is complete.
✍
Does your Cart have 4" Casters?*
(Such as a 030xx4. Your Caster Part
Numbers are given here.)
4" Non-Locking Caster
150-5010-00
4" Locking Caster
150-5011-00
✍
Does your Cart have Glides?*
01
(Such as a 030xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
Glide Insert
Glide
525-1004-00
325-5042-00
03
Component list for part#'s
030xx, 035xx, 080xx, 085xx.
01 – Vertical Legs ..............................
Qty. 4 ............................. (see below)
15.10" Vertical Legs
(035xx, 085xx) ................................... 125-5050-xx
23.875" Vertical Legs
(030xx, 080xx) ................................ 125-5020-xx
02– Insert Screws ............................
Qty. 4 ......................... 325-5052-00
03– 1.75" Large End Caps ............
Qty. 2 ......................... 175-5021-xx
04– Caster Inserts ...........................
Qty. 4 ...................... 525-1000-00
05– 2
3
/
" Locking Casters ................
Qty. 2 ...................... 150-5003-00
8
06– Base Tube Screws .....................
Qty. 4 ......................... 325-5000-00
07– 2
3
/
" Non-Locking Casters ........
Qty. 2 ...................... 150-5002-00
8
08– PrinterCart Base Tube .............
Qty. 1 ............................. (see below)
24" Wide Base Tube .................................................
125-5031-xx
36" Wide Base Tube .................................................
125-5058-xx
09– Clamp Screws ...........................
Qty. 8 ......................... 325-5086-03
10– Shelf Supports ..........................
Qty. 8 ......................... 175-5060-xx
Anthro Corporation Technology Furniture
March 2006
SAVE THESE INSTRUCTIONS!
TECHNOLOGY FURNITURE
®
13
12
11
14
02
07
04
06
08
05
11– Shelf Clamps .............................
Qty. 8 ......................... 175-5059-xx
12– PrinterCart Shelf .......................
Qty. 2 ............................. (see below)
24" Wide PrinterCart Shelf .....................................
36" Wide PrinterCart Shelf .....................................
13– 1.5" Small End Caps ...............
Qty. 4 ......................... 175-5020-xx
*
14– Support Screws ........................
Qty. 8 ......................... 325-5010-00
*
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
*
Fasteners included, which are not counted in the Parts List.
To make the assembly of your Anthro PrinterCart even easier, we
have included all of the required tools (not shown above). The handy
Hex Driver Bit can be used in your electric drill in place of the Hex Driver.
Hex Driver
5
/
" ........................
Qty. 1 ....................... 375-5000-00
32
Hex Driver Bit
5
/
" ..................
Qty. 1 ....................... 375-5003-00
32
®
10450 SW Manhasset Drive Tualatin, Oregon 97062
10
09
100-6017-xx
100-6107-xx
anthro.com
Need help?
Do you have a question about the PrinterCart and is the answer not in the manual?
Questions and answers